Hellenbrand ProMate Series Owner's Manual page 38

TWin AlTernATinG uPflOW SYSTeM SPeCifiCATiOnS
PROMATE 7.1 TA SPECIFICATIONS
UPFLOW-HIGH EFFICIENCY TWIN ALTERNATING
MODEL
FACTORY PRESET MINUTES
PRE-RINSE: **
GALLONS
Fill MINUTES
GALLONS
BRINE/RINSE
GALLONS
BACKWASH: MINUTES
GALLONS
RINSE: MINUTES
GALLONS
TOTAL REGENERATION IN GALLONS @35
PSI, INCLUDES BRINE MAIKE UP.
REFILL-POUNDS OF SALT
HIGH EFFICIENCY
LOW SALT
MEDIUM SALT
Capacity-
HIGH EFFICIENCY SALT
LOW SALT
MEDIUM SALT
GRAINS OF HARDNESS REDDUCED PER
POUND OF SALT AT FACTORY SETTING
Service Flow Rate***
FLOW RATE AT 10 PSI
FLOW RATE AT 15 PSI
Other Data
RESIN, CUBIC FOOT
HAC (CU FT)
MINERAL TANK DIMENSION*
BRINE TANK DIMENSION
DRAIN LINE FLOW CONTROL
BRINE LINE FLOW CONTROL
INJECTOR, SIZE-COLOR
INJECTOR DRAW RATE AT 35 PSI
INJECTOR SLOW RINSE AT 35 PSI
* Vortech Tanks do not require gravel
Factory Settings are Bold. Actual programed capacity has been adjusted for non-metered regeneration water.
System conforms to ANSI/NSF 44 for specific performance claims as verified and substantiated by test data. Efficiency is measured by
a laboratory test as described in ANSI/NSF 44, testing represents maximum efficiency system can achieve. The operational efficiency
achieved after the system is installed may be less than tested efficiency due to application parameters such as water hardness, TDS and
other contaminants that reduce the softeners capacity. These high efficiency-rated softeners are Demand-Initiated Regenerating (DIR)
Softeners which comply with specific performance specifications intended to minimize the amount of brine and water used in operation.
If installation hardness is not 20 gr adjust accordingly.
If application demands 1 gpg or less in service flow at peak flows, please contact technical service for assistance.
** This cycle currently not used.
***Maximum service flow rate is 8 gpm per cubic foot at efficiency salting.
38
MINUTES
MINUTES
PM7.1-032 PM7.1-042
off off
off off
2.2 3
1.1 1
60.0 75.0
9.0 12.0
12.0 12.0
8.4 12.0
8.0 8.0
5.60 8.00
24.1 33.5
3.3 4.4
4.5 6
8 10.6
16,344 21,951
20,688 27,785
27,944 37,530
4952 4988
7.2 7.1
10.25 9.85
1 1.33
- -
8x44VT 9x48VT
18x40 18x40
0.7 1
0.5 0.5
A-Black B-Brown
0.063 0.09
0.15 0.16
PM7.1-059 PM7.1 DMT-059
off
off
4.1
2.1
75.0
18.0
12.0
15.6
8.0
10.40
46.1
6.2
8.3
14.8
29,267
37,045
50,038
4720
8.2
11.53
1.85
-
10x54VT
18x40
1.3
0.5
C-Violet
0.135
0.24
off
off
4.1
2.1
75.0
18.0
12.0
15.6
8.0
10.40
46.1
6.2
8.3
14.8
29,267
37,045
50,038
4720
7.8
10.65
1.85
0.33
10x60VT
18x40
1.3
0.5
C-Violet
0.135
0.24
80502