Hellenbrand H-100 series Owner's Manual
Hide thumbs Also See for H-100 series:

Advertisement

12 Volt Electronics
Owner's Manual
Manufactured by:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H-100 series and is the answer not in the manual?

Questions and answers

Lois Jean Phelps
April 24, 2025

why is softener flashing "softening"

1 comments:
Mr. Anderson
May 12, 2025

The Hellenbrand H-100 series softener flashes "softening" to indicate that the system is currently in the softening mode and actively treating the water.

This answer is automatically generated

Cindy Smith
March 2, 2025

How do I reset the regeneration time to 2AM on my H-100 Series? It has been regenerating during day hours. Thank you!

1 comments:
Mr. Anderson
March 2, 2025

To reset the regeneration time to 2 AM on your Hellenbrand H-100 Series:

1. Enter the settings menu.
2. Navigate to Step 4 - Next Regeneration Time (hour).
3. Use the up (▲) or down (▼) buttons to set the hour to 2.
4. Ensure AM/PM toggles correctly after 12.
5. Press NEXT to go to Step 5 - Next Regeneration Time (minutes).
6. Use the up (▲) or down (▼) buttons to set the minutes to 00.
7. Press NEXT to exit the Installer Displays/Settings.

Your system will now regenerate at 2:00 AM.

This answer is automatically generated

Summary of Contents for Hellenbrand H-100 series

  • Page 1 12 Volt Electronics Owner’s Manual Manufactured by:...
  • Page 2 TABLE OF CONTENTS JOB SPECIFICATION SHEET OPERATING CONDITIONS...
  • Page 3: Soft Water Basics

    SOFT WATER BASICS Hardness Regeneration Maintenance of Your Softener Salt: Cleaning Salt Keeper: FREQUENTLY ASKED QUESTIONS...
  • Page 4: Bypass Valve Operation

    To prevent these unnecessary, and expensive repairs that are not covered under warranty, Hellenbrand recommends installing an in-line filter system ahead of softeners. Make certain the current supply is uninterrupted and cannot be turned off with another switch.
  • Page 5 INSTALLATION INSTRUCTIONS...
  • Page 6 PROGRAMMING General Information Initial Start Up...
  • Page 7: Set Time Of Day

    SET TIME OF DAY STEP 1 STEP 2 STEP 3 INSTALLER DISPLAYS/SETTINGS STEP 1 Hardness: STEP 2 Day Override: STEP 3 STEP 4 STEP 5...
  • Page 8: User Displays/Settings

    USER DISPLAYS/SETTINGS General Operation Regeneration Mode Manual Regeneration WATER SOFTENER DISINFECTION...
  • Page 9: Water Softener Draining Procedure

    WATER SOFTENER DRAINING PROCEDURE MISCELLANEOUS...
  • Page 10: Troubleshooting

    TROUBLE SHOOTING...
  • Page 11 TROUBLE SHOOTING...
  • Page 12 HELLENBRAND H-100 SERIES CONDITIONER & BRINE TANK ASSEMBLIES...
  • Page 13 FRONT COVER AND DRIVE ASSEMBLY DRIVE CAP ASSEMBLY, DOWNFLOW PISTON, REGENERANT PISTON AND SPACER STACK ASSEMBLY...
  • Page 14 INJECTOR CAP, INJECTOR SCREEN, INJECTOR, PLUG AND O-RING REFILL AND REFILL PORT PLUG...
  • Page 15 DRAIN LINE - 3/4” DRAIN LINE - 1”...
  • Page 16 WATER METER AND METER PLUG BYPASS VALVE...
  • Page 17 INSTALLATION FITTING ASSEMBLIES...
  • Page 18 HELLENBRAND H-100 SERIES SYSTEM SPECIFICATIONS ED -“ELECTRONIC DEMAND” TC -“TIME CLOCK”...
  • Page 19 TABLE 4 - BACKWASH NORMAL LENGTH SOFTENER TABLE 5 - BACKWASH LONGER LENGTH SOFTENER TABLE 6 - PROGRAMMING OPTIONS...
  • Page 20 GENERAL SPECIFICATIONS ± HELLENBRAND H-100 SERIES WARRANTY...

Table of Contents

Save PDF