Checking After The Installation; Execute The Itb Equilibrium Position Detection; Auto Adjust Gradation; When "Plain" Paper Is Used - Canon imageRUNNER ADVANCE C5045 Series Service Manual

CheckingaftertheInstallation
1)InServiceMode,checktheresultofDrumUnitinitialization.
Makesurethatthevalueoftheinstalledcoloris[0to2].
•
Service Mode > COPIER > DISPLAY > HV-STS > THCK-Y
•
Service Mode > COPIER > DISPLAY > HV-STS > THCK-M
•
Service Mode > COPIER > DISPLAY > HV-STS > THCK-C
MEMO:
Ifanerrorcode[E061-xxxx]isdisplayedonthescreenorthevalueisnotappropriate,
1. Turn OFF the power, refit the Drum Unit and turn On the power again.
2.Iftheaboveworkdoesnotsolvetheproblem,executeinitializationoftheDrumUnit
foreachcolorinServiceMode.
•
Service Mode > COPIER > FUNCTION > DPC > DRMRSETY
•
ServiceMode>COPIER>FUNCTION>DPC>DRMRSETM
•
ServiceMode>COPIER>FUNCTION>DPC>DRMRSETC
2)ChecktheresultofinitializationofdevelopingtonerratioinServiceMode.
Checkthateachvalueiswithintherangeof32to68,andthenwritedownthevalueonthe
servicelabelattherearsideoftheFrontCover.
•
Service Mode > COPIER > ADJUST > DENS > CONT-Y
•
ServiceMode>COPIER>ADJUST>DENS>CONT-M
•
Service Mode > COPIER > ADJYST > DENS > CONT-C
•
Service Mode > COPIER > ADJYST > DENS > CONT-K
3)ChecktheDevelopingPatchinitialization.
Checkthateachvalueiswithintherangeof340to640,andthenwritedownthevalueon
theservicelabelattherearsideoftheFrontCover.
•
Service Mode > COPIER > ADJUST > DENS > SGNL-Y
•
ServiceMode>COPIER>ADJUST>DENS>SGNL-M
•
ServiceMode>COPIER>ADJUST>DENS>SGNL-C
•
ServiceMode>COPIER>ADJUST>DENS>SGNL-K
MEMO:
IfanErrorCode[E020-xxxx]isdisplayedonthescreenorthevalueisnotappropriate
instep2)orstep3),turnOFFandthenONthemainpoweroftheHostMachine;and
then execute initialization of YMCK Developing Assembly.
•
ServiceMode>COPIER>FUNCTION>INSTALL>INISET-4
9

MEMO:
SettingtheADFbeforeexecutingAutoAdjustGradation.
Refertothe"Afterinstallationsetting"inthe"theDuplexColorImageReaderUnit-B1,
ColorImageReaderUnit-B1/B2installationprocedure".
ExecutetheITBEquilibriumPositionDetection
In the case that the floor surface is either warped or uneven, execute the following work.
1)Checkthatthemainbodyisinstandbystate.
2)ExecutetheITBEquilibriumPositionDetectionServiceMode(COPIER>FUNCTION>MISC-
P>ITB-INIT)(Level1).Thisservicemodewilltakeapprox.2to3minutes.
AutoAdjustGradation
AutoAdjustGradationisexecutedwith"Plain","Heavy1/Heavy2"or"Heavy3".
When"Plain"paperisused
1)Cleanthesurfaceofcopyboardglass.
2)SetA3,A4,11×17orLTRpaperinthecassette.
3)Select[Settings/Registration]>[Adjustment/Maintenance]>[AdjustImageQuality]>[Auto
AdjustGradation]>[Plain]>[FullAdjust].
4)Selectthecassetteforthetestprintandpress"OK".
5)Then,followthedirectiondisplayedonUI.
When"Heavy1/Heavy2"paperisused
1)Cleanthesurfaceofcopyboardglass.
2)Settheheavypaperinthecassette.
3)Select[Settings/Registration]>[Adjustment/Maintenance]>[AdjustImageQuality]>[Auto
AdjustGradation]>[Heavy1/Heavy2]>[FullAdjust].
4)Selectthecassetteforthetestprintandpress"OK".
5)Then,followthedirectiondisplayedonUI.
When"Heavy3"paperisused
1)SettheheavypaperontheMulti-purposeTray.
2)Select[Settings/Registration]>[Adjustment/Maintenance]>[AdjustImageQuality]>[Auto
AdjustGradation]>[Heavy3]>[FullAdjust].
3)Selectthecassetteforthetestprintandpress"OK".
4)Then,followthedirectiondisplayedonUI.
9 
9-26
9-26