Recording Level Adjustment - JVC GY-DV500U Instructions Manual

6. SETTING AND ADJUSTMENTS BEFORE SHOOTING

6-8 Recording Level Adjustment

VF
ZEBRA
OFF
SKIN AUTO
ON
AREA WHITE
ACCU
FOCUS
VTR
AUDIO
TAKE
LEVEL CH-1
CH-1 recording level control
For each audio channel, use the AUDIO SELECT switches to
select whether the recording level adjustment should be set to
AUTO mode or MANUAL mode.
• When set to AUTO: Recording level is fixed. In this mode,
the recording level control does not
function.
• When set to MANUAL: Recording level can be adjusted
using the recording level controls for
each audio input.
Adjusting the recording level control of the front section
The recording level control on the front section only affects
the CH-1 channel sound.
To use the recording level control on the front section, make
the following settings.
• Set the CH-1 AUDIO SELECT switch to MANUAL.
• Set the VCR Setup Menu item No. 246 FRONT VOLUME
ENABLE to "ENABLE".
CAUTION:
The recording level controls on the side section work
regardless of the setting of the VCR Setup Menu item No.
246 FRONT VOLUME ENABLE.
Manual Adjustment of Recording Level
The recording level can be adjusted manually when the GY-
DV500 is in the record, record-pause or stop mode.
1.
Set the AUDIO SELECT switch of the channel whose
recording level that you want to adjust manually to MANUAL.
2.
Rotate the recording level control corresponding to the audio
input to be adjusted.
• Adjust so that the peak level does not exceed the -3dB
point when a loud sound is input.
• With microphone input, since the limiter circuit is activated,
the recording level will not exceed 0 dB even if the
recording level control is turned up.
48
FILTER
1 3200k ALARM
2 5600k
3 5600k+ND
SHUTTER STATUS
MONITOR
MENU
AUTO IRIS FULL AUTO BLACK LOLUX
BACK L STRETCH
NORMAL NORMAL
SPOT L COMPRESS
NG POWER
ON OFF
CH-1 recording level control
CH-1 Audio
select switch
OPERATE/WARNING
LIGHT
RESET ON
OFF
MONITOR
SELECT COUNTER
CTL
TC
UB
AUDIO
CH-1 CH-2
LEVEL
CH-2 recording level control
How to use the recording level control on
the front section
1 Set the recording level control on the front section to
maximum (10) position.
2 Initially, adjust the recording level using the CH1 recording
level control on the side.
3 When a loud sound is input during recording, use the
recording level control on the front section to lower the
recording level.
Level meter
CH 1
40 30
CH 2
32k 48k
SP
AUD LOCK
MENU
REMAIN
Viewfinder Status 1 Mode
F 5 . 6
STBY
Indicator level (reference)
–38 –32
CAUTION:
When the AUDIO INPUT LINE/MIC switch on the rear
section is set to MIC, be sure to check that the microphone
is connected to the AUDIO INPUT connector. If the
microphone is not connected, increasing the recording level
could cause noise from the input connector to be recorded
on the tape. When the microphone is not connected to the
AUDIO INPUT connector on the rear panel, set the LINE/
MIC switch to LINE or turn down the recording level control.
CH-2 Audio
select switch
AUTO
MANUAL
AUDIO SELECT
AUDIO INPUT
CH-1 CH-2
CH-1 AUDIO CH-2
FRONT
REAR
LEVEL
AUTO OFF DEW
OVER
20 10 0 dB
SERVO RF L i
OVER
PB NDF HOLD
H M S F
E BATT F
REV FWD
H M
ACCU - FOCUS
G
F
I
SD
B
CH1 - - - - + - -
CH2 - - - - + - - M 0 9 9
< 6 0 1 . 2 4V
Audio leve
–26 –20 –14 –8 –2dB