Recording Level Adjustment - JVC GY-DV5001 Instructions Manual

6. SETTING AND ADJUSTMENTS BEFORE SHOOTING

6-8 Recording Level Adjustment

VF
OFF ZEBRA
SKIN AUTO
ON
AREA WHITE
ACCU
FOCUS
VTR AUDIO
LEVELE CH-1
5
CH-1 audio input level control
For each audio channel, use the AUDIO SELECT switches to
select whether the audio level adjustment should be set to
AUTO mode or MANUAL mode.
● When set to AUTO
● When set to MANUAL: Audio input level can be adjusted
MEMO:
The reference level for audio recorded on the tape can be
set with the AUDIO REF. LEVEL item on the AUDIO menu
screen. (–20 dB or –12 dB). The level will change for both
CH1 and CH2.
Adjusting the audio input level control on the front
section
The audio input level control on the front section only affects
the CH-1 channel sound.
To use the audio input level control on the front section, make
the following settings.
● Set the CH-1 AUDIO SELECT switch to MANUAL.
● Set the CH-1 FRONT VR. item on the AUDIO menu screen
to ENABLE.
MEMO:
The audio input level controls on the side section work
regardless of the setting of CH-1 FRONT VR. item on the
AUDIO menu screen.
The audio input level can be adjusted manually when the GY-
DV5000 is in the record, record-standby or stop mode.
1.
Set the AUDIO SELECT switch of the channel whose audio
level that you want to adjust manually to MANUAL.
2.
Rotate the audio input level control corresponding to the
audio input level to be adjusted.
● Adjust so that the peak level does not exceed the –3dB
point when a loud sound is input.
E-50
EDITSEARCH
MONITOR
FILTER
1 3200K
2 5600K 1 8 / ND
.3 5600K
.4 5600K 1 64 / ND
STATUS
SHUTTER
MENU
AUTO IRIS FULL AUTO BLACK LOLUX
MODE
BACK L STRETCH
VTR
NORMAL NORMAL
SPOT L COMPRESS
CAM
POWER VTR
ON OFF
CH-1 audio input level
control
: Audio input level is fixed. In this
mode, the audio input level
control does not function.
using the audio input level
controls for each audio input.
(The AUTO mode is selected in
the Full Auto shooting mode.)
OPEN
LCD BRIGHT DISPLAY
AUDIO
LEVEL PULL
OPEN
FRONT
REAR
CH-1 CH-2
CH-1 CH-2
AUDIO INPUT
AUDIO SELECT
CH-1 CH-2
AUTO
MANUAL
CH-1 AUDIO SELECT switch
CH-2 audio input level
control
Using the audio input level control on the front section
1
Set the audio input level control on the front section to
maximum (10) position.
2
Initially, adjust the audio input level using the CH-1 audio
input level control on the side.
3
If a loud sound is input during recording, use the audio
input level control on the front section to lower the audio
input level.
Viewfinder Status 1 Mode
FIL1
F5.6
STBY 01/02/03 AM01:23:45
Indicator level (reference)
–26 –20
CAUTION:
● When the AUDIO INPUT LINE/MIC switch is set to MIC,
be sure to check that the microphone is connected to
the AUDIO INPUT connector. If the microphone is not
connected, increasing the audio level could cause noise
from the input connector to be recorded on the tape.
When the microphone is not connected to the AUDIO
INPUT connector, set the AUDIO INPUT LINE/MIC
switch to LINE or turn down the audio level control.
● In the Full Auto shooting mode, the audio level volume
cannot be adjusted with the audio level controls on the
front and side sections.
LCD BRIGHT DISPLAY
AUDIO
PULL
LEVEL
OPEN
FRONT
REAR
CH-1 CH-2
CH-1 CH-2
AUDIO INPUT
AUDIO SELECT
CH-1 CH-2
AUTO
MANUAL
CH-2 AUDIO
SELECT switch
00:00:00:00
20min
FAS
–3dB
FAW
I
SD
B
48k 12.2V
Audio level
–15 –11 –7 –3 0dB OVER