How To Use The S.s.f. Function - JVC GY-DV500U Instructions Manual

10-2 How to Use the S.S.F. Function

CUE Mode
1.
Set the S.S.F. mode as CUE mode.
Set the VCR Setup Menu item No. 398 S.S.F. MODE to
"CUE".
See page 69.
• The CUE mode is indicated in the lower part of the Status
1 screen in the viewfinder.
CH1 - - - - + - -
F 5 . 6 CH2 - - - - + - -
STBY < 6 0
2.
Press the VTR trigger button to start the recording.
3.
When you reach the point that you want to memorize as
the CUE point, press the TAKE button.
• The time code data of the point where the TAKE button is
pressed is stored in the unit's memory as CUE data.
The LOG button's LED lights during memorization of the
CUE point and the " " mark is shown in the viewfinder.
Press the TAKE button each time you reach a point that
you want to memorize as CUE data.
4.
Stop the recording.
Press the VTR trigger button.
Note:
• Once the S.S.F. data has been written to a videocassette, it is not possible to record S.S.F. data to the tape again.
• Once a tape with recorded S.S.F. data is rewound but not ejected before playback or recording is performed on it again, the
previous S.S.F. data cannot be automatically erased when S.S.F. data are recorded (when you overwrite the previous image).
Therefore, the S.S.F. data of the overlapped sections will not correspond to the video image.
Furthermore, please note that the time code data may differ from the actual data if recording is started in the CUE mode in
this situation.
10. S.S.F. (Super Scene Finder) FUNCTION
VF
ZEBRA
OFF
SKIN AUTO
ON
AREA WHITE
ACCU
FOCUS
VTR
AUDIO
TAKE
LEVEL CH-1
VTR trigger button
ACCU - FOCUS
G
F
I
SD
B
CUE mode
Number of
C 0 9 9
memorized
1 . 2 4V
scenes
* This indicator
is not indicat-
ing the number
of the CUE
point.
TAKE button
MARK Mode
1.
Set the S.S.F. mode as MARK mode.
Set the VCR Setup Menu item No. 398 S.S.F. MODE to
"MARK".
See page 69.
• The MARK mode is indicated in the lower part of the
Status 1 screen in the viewfinder.
CH1 - - - - + - -
F 5 . 6 CH2 - - - - + - -
STBY
2.
Press the VTR trigger button to start the recording.
3.
When you reach the scene that you want to memorize, press
the TAKE button.
• The time code data of the point where the TAKE button is
pressed is stored in the unit's memory as the start point
of the scene.
4.
When you reach the scene that you want to memorize as
the ending point, press the TAKE button again.
• The time code data of the point where the TAKE button is
pressed is stored in the unit's memory as the ending point
of the scene.
• The LOG button's LED lights during memorization of the
IN point and the " " mark is shown in the viewfinder.
The LOG button's LED remains off during memorization
of the OUT point and the " " mark is not shown in the
viewfinder.
For each scene that you want to memorize, repeat steps
3. and 4 .
5.
Stop the recording.
Press the VTR trigger button.
ACCU - FOCUS
G
F
I
SD
B
MARK mode
Number of
M 0 9 9
memorized
< 6 0 1 . 2 4V
scenes
61