Controls, Indicators And Connectors; Front Section - JVC GY-DV500U Instructions Manual

2. CONTROLS, INDICATORS AND CONNECTORS

2-1 Front Section

q
w
e
OFF
ON
r
t
y
1
Viewfinder mount base, sliding securing ring
Mount the viewfinder on the base and secure it using the
sliding securing ring.
See "Attaching the Viewfinder" on page 31.
2
[VF] Viewfinder connector (6-pin)
Connect the cable from the viewfinder here.
3
[MIC IN] Microphone input connector (XLR 3-pin)
Balanced 3-pin connector for camera microphone.
• When the camera microphone to be connected is a
phantom microphone or other type of microphone, set
the CAM MIC 48V item on the Camera Setup menu. See
page 77.
• When using a microphone with this connector, set the
AUDIO INPUT switches
accordance with the audio channel (CH1 or CH2) to be
recorded.
See page 14.
1
3
2
CAUTION:
The provided microphone is a phantom microphone.
Please confirm that the CAM MIC 48 V item on the
Camera SETUP Menu is set to "ON".
When using a microphone other than a phantom
microphone, first set the CAM MIC 48 V item to "OFF"
before connecting the microphone. Otherwise the
microphone may be damaged.
10
!1
VF
!0
ZEBRA
SKIN AUTO
AREA WHITE
o
ACCU
FOCUS
VTR
AUDIO
TAKE
i
LEVEL CH-1
u
7 8
on page 14 to FRONT in
Pin No. Function
1 GND
2 HOT
3 COLD
4
[LENS] Lens control connector
Connect 12-pin lens control cable from lens.
Pin No. Function
1 RET switch
2 VCR trigger
3 GND
4 Lens AUTO/MANU control
5 IRIS control
6 +12V DC
5
[ZEBRA] Switch
When this switch is ON, a zebra pattern is superimposed
on the viewfinder areas having video levels with a luminance
level of 70% to 80%. This pattern can be used as a reference
for manual adjustment of the lens iris.
* The zebra patterns are only displayed on the viewfinder
screen. The zebra patterns are not generated for the
MONITOR OUT or Y/C OUT output.
See "Zebra Pattern during Manual Adjustment" on page
80.
• The default value is 70% - 80%. The luminance level can
be changed with the ZEBRA setting in the VF DISPLAY
Menu screen.
See "ZEBRA" item on page 72.
While this switch is pressed to the SKIN AREA side, the
color tone areas specified with the SKIN DTL ADJUST item
on the ADVANCED PROCESS MENU are indicated in the
viewfinder. The switch returns to the OFF position when
released.
See "How to Use Skin Detail" on page 84.
• The Skin Detail color tone areas are not indicated while
the VTR playback picture is shown in the viewfinder.
6
[VTR] VTR trigger button (record start/stop button)
Record start/stop can be effected with this button.
(It is interlocked with the VTR trigger button on the lens
section.)
7
[AUDIO LEVEL CH-1] CH-1 recording level control
Adjusts the recording level of the CH1 audio signal input.
Normally, the camera is used with the control set to the
maximum (10) position.
• To use this control, set the VCR Setup Menu item No.
246 FRONT VOLUME ENABLE to "ENABLE".
Note:
Even when the VCR Setup Menu item No. 246 is set to
DISABLE, the recording level changes slightly when this
control is turned.
8
[AUTOWHITE./ACCU FOCUS] switch
AUTO WHITE:
• First, position a white object to occupy 80% of the centre
of the image.
• Setting this switch to the upper position ("AUTO WHT")
will provide automatic adjustment for white balance.
* It is not activated in preset, full auto shooting, full-time
auto white balance and color bar modes.
See "White Balance Adjustment" on page 45.
Pin No. Function
7 IRIS position
8 IRIS A/R INPUT
9 EXTENDER position
10 ZOOM position
11 —
12 —