AMT Datasouth ACCEL-6300 User Manual page 208

Table D-6. Epson and IBM Escape Sequences––continued
Function
Set character spacing ..............
to 10 or 17.1 CPI
Set character spacing ..............
to 12 CPI
Set character spacing ..............
to 15 CPI
Start condensed printing ..........
Set character cell size ..............
5 characters/inch ........
6 characters/inch ........
6.6 characters/inch ........
7.5 characters/inch ........
8.5 characters/inch ........
10 characters/inch ........
12 characters/inch ........
13.3 characters/inch ........
15 characters/inch ........
17.1 characters/inch ........
20 characters/inch ........
Set intercharacter space .........
ASCII Hexadecimal
Horizontal Spacing
ESC P 1B 50
ESC M 1B 4D
ESC : 1B 3A
ESC g 1B 67
ESC SI 1B 0F
ESC ESC Z n 1B 1B 5A n
ESC ESC Z 8 1B 1B 5A 38
ESC ESC Z 4 1B 1B 5A 34
ESC ESC Z 2 1B 1B 5A 32
ESC ESC Z 0 1B 1B 5A 30
ESC ESC Z . 1B 1B 5A 2E
ESC ESC Z , 1B 1B 5A 2C
ESC ESC Z * 1B 1B 5A 2A
ESC ESC Z ) 1B 1B 5A 29
ESC ESC Z ( 1B 1B 5A 28
ESC ESC Z ' 1B 1B 5A 27
ESC ESC Z & 1B 1B 5A 26
ESC SP n 1B 20 n
Decimal
27 80 This sequence sets character spacing and character cell size
to 10 characters per inch. If condensed printing is on, this
sequence sets character spacing and character cell size to 17.1
chracters per inch.
Note: This sequence is not supported when the IBM XL24
emulation is active.
27 77 These sequences set character spacing and character cell
27 58 size to 12 characters per inch.
27 103 This sequence sets character spacing and character cell size
to 15 characters per inch. Condensed printing does not affect the
function of this sequence.
27 15 This sequence starts condensed printing, wherein character
spacing and character cell size are 17.1 characters per inch. A
DC2 code ends condensed printing.
27 27 90 n This sequence sets the character cell size so that characters
27 27 90 56 are the correct size for the spacing. The value of variable n
27 27 90 52 minus 32 defines a number of 1/120-inch increments to
27 27 90 50 move:
27 27 90 48
27 27 90 46 Character spacing = (n - 32) x 1/120-inch
27 27 90 44
27 27 90 42
27 27 90 41
27 27 90 40
27 27 90 39
27 27 90 38
27 32 n This sequence sets the amount of space for the printer to add to
the right of each character in addition to the space already
allowed in the design of the character. The value of variable n
defines the number of units to add. The unit size depends on the
current emulation and print quality. If the emulation is Epson JX,
the unit size is always 1/120 inch, regardless of the print quality.
In all other emulations, the unit size is 1/180 inch in letter- and
memo-quality and 1/120 inch in draft-quality.
For example, to add 1/4 inch to the right of each character
while in Epson LQ-2550 emulation and letter-quality, variable n
would be 45 decimal (1/4 inch = 45 x 1/180 inch).
User's Guide
Description
Code Sets D-29