Pitch Tab - Roland Integra-7 Parameter Manual

Studio Set –

PITCH tab

Parameter
Velo Fade Upper
Velo Range Upper
Velo Range Lower
Velo Fade Lower
Velo Sens Offset
PITCH tab
Octave Shift
Coarse Tune
Fine Tune
Bend Range
Porta Switch
8
Value
Level
Fade Lower
Range Lower
0–127
LOWER–127
1–UPPER
0–127
-63–+63
-3–+3
-48–+48
-50–+50
0–24, TONE
OFF, ON, TONE
Explanation
Fade Upper
Range Upper
Determines what will happen to the tone's level when the tone is played at a velocity greater than
Velo Range Upper . If you don't want the tone to sound at all, set this parameter to
*
This is not shown in PART VIEW -ALL- .
SN-A SN-A SN-A
(Ac .Piano) (Organ) (Other)
ü –
Specifies the highest velocity at which the part will sound .
* This is not shown in PART VIEW -ALL- .
Specifies the lowest velocity at which the part will sound .
* This is not shown in PART VIEW -ALL- .
Determines what will happen to the tone's level when the tone is played at a velocity lower than
Velo Range Lower . If you don't want the tone to sound at all, set this parameter to
* This is not shown in PART VIEW -ALL- .
SN-A SN-A SN-A
(Ac .Piano) (Organ) (Other)
ü –
Adjusts the velocity sensitivity . The higher the value, the greater the sensitivity .
* This is not shown in PART VIEW -ALL- .
SN-A SN-A SN-A
(Ac .Piano) (Organ) (Other)
–
ü
Adjusts the pitch of the part's sound up or down in units of an octave (+/-3 octaves) .
SN-A SN-A SN-A
(Ac .Piano) (Organ) (Other)
ü ü
Adjusts the pitch of the part's sound up or down in semitone steps (+/-4 octaves) .
Adjusts the pitch of the part's sound up or down in 1-cent steps (+/- 50 cents) .
MEMO
One cent is 1/100th of a semitone .
Specifies the amount of pitch change in semitones (2 octaves) that will occur when the Pitch Bend
Lever is moved . The amount of change when the lever is tilted is set to the same value for both left
and right sides . If you want to use the Pitch Bend Range setting of the tone assigned to the part,
"TONE."
set this to
SN-A SN-A SN-A
(Ac .Piano) (Organ) (Other)
ü ü
Specify whether portamento will be applied . Turn this parameter
Portamento and "OFF" when you don't . If you want to use the Portamento Switch setting of the
tone assigned to the part, set this to
*
This is not shown in PART VIEW -ALL- .
SN-A SN-A SN-A
(Ac .Piano) (Organ) (Other)
–
ü
Velocity
SN-S SN-D
ü ü ü
SN-S SN-D
ü ü ü
SN-S SN-D
–
ü ü
SN-S SN-D
–
ü ü
SN-S SN-D
–
ü ü
"ON"
when you want to apply
"TONE."
SN-S SN-D
–
ü ü
"0."
PCMS PCMD
ü ü
"0."
PCMS PCMD
ü ü
PCMS PCMD
ü ü
PCMS PCMD
–
ü
PCMS PCMD
ü ü
PCMS PCMD
–
ü