Program Change; Pitch Bend Change; System Exclusive Messages - Roland V-440HD Owner's Manual

MIDI implementation
❍Hold 1 (controller number 64)
Status 2nd byte
BnH 40H
❍Portamento (controller number 65)
Status 2nd byte
BnH 41H
❍Sostenuto (controller number 66)
Status 2nd byte
BnH 42H
❍Soft (controller number 67)
Status 2nd byte
BnH 43H
❍Legato (controller number 68)
Status 2nd byte
BnH 44H
❍Hold 2 (controller number 69)
Status 2nd byte
BnH 45H
❍Sound Controllers 1–10 (controller numbers 70–79)
Status 2nd byte
BnH 46 - 4FH
❍General Purpose Controllers 5–8 (controller numbers 80–83)
Status 2nd byte
BnH 50 - 53FH
❍Portamento Control (controller number 84)
Status 2nd byte
BnH 54H
❍Effect Depth 2-5 (controller number 92–95)
Status 2nd byte
BnH 5C - 5FH
●Program Change
Status 2nd byte
CnH ppH
pp= program number: 00H - 7FH (prog.1 - Prog.128)
* This selects the input for Channel A and Channel B. For more detailed information refer
to the Bank Select parameters.
* If a non-selectable Program Change is received, it will be ignored.
●Channel Pressure
Status 2nd byte
DnH vvH
* Just as for Control Change messages, you can make settings in MIDI Setup to use
Channel Pressure messages to control a wide variety of things. For details on the factory
settings, refer to "Settings Transmitted/Received Using MIDI" (p. 75).
●Pitch Bend Change
Status 2nd byte
EnH llH
mm, ll= pitch bend value:00 00H - 40 00H - 7F 7FH (-8192 - 0 -+8191)
* Just as for Control Change messages, you can make settings in MIDI Setup to use Pitch
Bend Change messages to control a wide variety of things. For details on the factory
settings, refer to "Settings Transmitted/Received Using MIDI" (p. 75).

■System exclusive messages

Status Data bytes
F0H iiH, ddH,...,eeH
F0H: System Exclusive Message status
ii= ID number: An ID number (manufacturer ID) that indicates the manufacturer to which
the exclusive message belongs. Roland's manufacturer ID is 41H. ID numbers 7EH and 7FH
are used for Universal Non-realtime Messages (7EH) and Universal Realtime Messages
(7FH) to extend the MIDI specification.
dd, .. ee= data: 00H–7FH (0–127)
F7H: EOX (End Of Exclusive)
70
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
3rd byte
xxH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
Status
F7H
●Data Set 1 (DT1)
This is the message that transfers actual data, and is used to specify data for a device.
Status Data bytes
F0H 41H, dev, 00H, 00H, 10H, 12H,
aaH, bbH, ccH, ddH, ..., eeH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H–1FH, factory setting is 10H)
00H 1st byte of model ID (V-440HD)
00H 2nd byte of model ID (V-440HD)
10H 3rd byte of model ID (V-440HD)
12H Command ID (DT1)
aaH Upper byte of address
bbH Address
ccH Address
ddH Data: the actual data to be transmitted. Multi-byte data is transmitted
in the order of the address.
: :
eeH Data
sum Checksum
F7H EOX (End Of Exclusive)
Status Data bytes
F0H 41H, dev, 00H, 51H,
12H, aaH, bbH, ccH,
ddH, ..., eeH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H–1FH, factory setting is 01H)
00H Upper byte of model ID (V-Link message)
51H Lower byte of model ID (V-Link message)
12H Command ID (DT1)
aaH Upper byte of address
bbH Address
ccH Address
ddH Data: the actual data to be transmitted. Multi-byte data is transmitted
in the order of the address.
eeH Data
sum Checksum
F7H EOX (End Of Exclusive)
* For details on setting the address, size, and checksum, refer to "Calculating the
checksum ('H' is appended to hexadecimal numbers)" (p. 75).
* Data that exceeds 256 bytes must be divided into packets of 256 bytes or less for
transmission. If a subsequent "Data Set 1" message is transmitted, an interval of at least
20 ms must be left between packets.
2. MIDI messages transmitted from MIDI OUT
* If MIDI Thru is ON, MIDI messages received at MIDI IN are re-transmitted without
change from MIDI OUT.
* If MIDI Thru is ON, messages from the V-440HD itself will not be transmitted.
■Channel voice messages
● Control Change
* The messages assigned in MIDI Setup will be transmitted when you operate the panel.
The control changes that can be used are CC#1–5, 7–31, and 64–95. For the factory
settings, refer to "Settings Transmitted/Received Using MIDI" (p. 75).
❍Bank Select (controller numbers 0, 32)
Status 2nd byte
BnH 00H
BnH 20H
mm, ll= bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* When you select channel A or channel B inputs, make memory settings, or specify how
sub-channels are mixed in Presentation mode, these messages will be transmitted in
conjunction with Program Changes.
Status
F7H
Status
F7H
3rd byte
mmH
llH