Ring Modulator; Tremolo; Auto Pan; Slicer - Roland Integra-7 Parameter Manual

MFX Parameters

15: Ring Modulator

This is an effect that applies amplitude modulation (AM) to the
input signal, producing bell-like sounds . You can also change the
modulation frequency in response to changes in the volume of the
sound sent into the effect .
L in
Ring Mod
R in
Ring Mod
Parameter Value
Frequency # 0–127
Sens # 0–127
Polarity UP, DOWN
Low Gain -15–+15 dB
High Gain
-15–+15 dB
D100:0W
Balance #
–D0:100W
Level 0–127

16: Tremolo

Cyclically modulates the volume to add tremolo effect to the sound .
L in
Tremolo
R in
Tremolo
Parameter Value
TRI, SQR, SIN,
SAW1, SAW2
Mod Wave
SAW1
0 .05–10 .00 Hz,
Rate #
note
Depth #
0–127
Low Gain -15–+15 dB
High Gain
-15–+15 dB
Level 0–127
78
L out
2-Band EQ
R out
2-Band EQ
Explanation
Adjusts the frequency at which
modulation is applied .
Adjusts the amount of frequency
modulation applied .
Determines whether the frequency
modulation moves towards
higher frequencies (UP) or lower
frequencies (DOWN) .
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the effect sound (W)
Output level
L out
2-Band EQ
R out
2-Band EQ
Explanation
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
SAW2
Frequency of the change
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level

17: Auto Pan

Cyclically modulates the stereo location of the sound .
L in
Auto Pan
R in
Auto Pan
Parameter Value
TRI, SQR, SIN,
SAW1, SAW2
Mod Wave
SAW1
R
L
0 .05–10 .00 Hz,
Rate #
note
Depth # 0–127
Low Gain -15–+15 dB
High Gain -15–+15 dB
Level 0–127

18: Slicer

By applying successive cuts to the sound, this effect turns a
conventional sound into a sound that appears to be played as a
backing phrase . This is especially effective when applied to sustain-
type sounds .
You can use MFX CONTROL to restart the step sequence from the
beginning (p . 97) .
L in Slicer
R in
Slicer
Parameter Value
Step 01–16
L64 –63R
0 .05 –10 .00 Hz,
Rate #
note
Attack # 0–127
Input Sync Sw OFF, ON
Input Sync
0–127
Threshold
Mode LEGATO, SLASH
L out
2-Band EQ
R out
2-Band EQ
Explanation
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
SAW2
R
L
Frequency of the change
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
L out
R out
Explanation
Level at each step
Rate at which the 16-step sequence
will cycle
Speed at which the level changes
between steps
Specifies whether an input note will
cause the sequence to resume from
the first step of the sequence (ON)
or not (OFF)
Volume at which an input note will
be detected
Sets the manner in which the
volume changes as one step
progresses to the next .
LEGATO: The change in volume
from one step's level to the next
remains unaltered . If the level of a
following step is the same as the one
preceding it, there is no change in
volume .
SLASH: The level is momentarily
set to 0 before progressing to the
level of the next step . This change
in volume occurs even if the level of
the following step is the same as the
preceding step .