Step Lfo Tab - Roland Integra-7 Parameter Manual

Parameter
Offset
Delay Time
Delay Time KF
Fade Mode
Fade Time
Key Trigger
Pitch Depth
TVF Depth
TVA Depth
Pan Depth

STEP LFO tab

Step Type
LFO Step1-16
Value
-100, -50, 0, +50, +100
0–127
-100–+100
ON<, ON>, OFF<, OFF>
0–127
OFF, ON
-63–+63
-63–+63
-63–+63
-63–+63
TYP1, TYP2
-36–+36
Explanation
Raises or lowers the LFO waveform relative to the central value (pitch or cutoff frequency) . Positive
settings will move the waveform so that modulation will occur from the central value upward . Negative
"-"
settings will move the waveform so that modulation will occur from the central value downward .
Delay Time (LFO Delay Time) specifies the time elapsed before the LFO effect is applied (the effect
continues) after the key is pressed (or released) .
* "How to Apply the LFO"
After referring to
achieved .
MEMO
When using violin, wind, or certain other instrument sounds in a performance, rather than
having vibrato added immediately after the sounds are played, it can be effective to add the
vibrato after the note is drawn out somewhat . If you set the Delay Time in conjunction with the
Pitch Depth parameter and Rate parameter, the vibrato will be applied automatically following
a certain interval after the key is pressed . This effect is called
Adjusts the value for the Delay Time parameter depending on the key position, relative to the
C4 key (center C) . To decrease the time that elapses before the LFO effect is applied (the effect is
continuous) with each higher key that is pressed in the upper registers, select a positive value; to
increase the elapsed time, select a negative value . Larger settings will produce greater change .
If you do not want the elapsed time before the LFO effect is applied (the effect is continuous) to
change according to the key pressed, set this to
Time
C1 C2 C3 C4
Specifies how the LFO will be applied .
* "How to Apply the LFO"
After referring to
achieved .
Specifies the time over which the LFO amplitude will reach the maximum (minimum) .
* After referring to "How to Apply the LFO"
achieved .
Specifies whether the LFO cycle will be synchronized to begin when the key is pressed (ON) or not
(OFF) .
Specifies how deeply the LFO will affect pitch .
* You can control this parameter using the Matrix Control .
Specifies how deeply the LFO will affect the cutoff frequency .
* You can control this parameter using the Matrix Control .
Specifies how deeply the LFO will affect the volume .
*
You can control this parameter using the Matrix Control .
Specifies how deeply the LFO will affect the pan .
* You can control this parameter using the Matrix Control .
MEMO
Positive "+" and negative "-" settings for the Depth parameter result in differing kinds of
change in pitch and volume . For example, if you set the Depth parameter to a positive
value for one partial, and set another partial to the same numerical value, but make it negative
"-", the modulation phase for the two partials will be the reverse of each other . This allows you
to shift back and forth between two different partials, or combine it with the Pan setting to
cyclically change the location of the sound image .
NOTE
In the Pan Depth parameter settings, if the Structure Type parameter is set to any value from
"2" through "10," the output of partial 1 and 2 will be combined into partial 2, and the output
of partial 3 and 4 will be combined into partial 4 . For this reason, partial 1 will follow the
settings of partial 2, and partial 3 will follow the settings of partial 4 (p . 52) .
When generating an LFO waveform from the data specified in LFO Step1–16, specify whether the
level will change abruptly at each step (TYP1) or will be connected linearly (TYP2) .
Specifies the data for the Step LFO .
If the LFO Pitch Depth is +63, each +1 unit of the step data corresponds to a pitch of +50 cents .
PCM Synth Tone (PCMS) –
(p . 62), change the setting until the desired effect is
"Delay Vibrato."
"0."
-100
-50
0
+50
+100
Key
C5 C6 C7
(p . 62), change the setting until the desired effect is
(p . 62), change the setting until the desired effect is
STEP LFO tab
"+"
"+"
61