Osc Tab; Pitch Tab; Filter Tab - Roland Integra-7 Parameter Manual

SuperNATURAL Synth Tone (SN-S) –
Parameter

OSC tab

Partial Switch
Wave
Wave Variation
Wave Number
Wave Gain
Pulse Width Mod Depth
Pulse Width
Pulse Width Shift
Super Saw Detune

PITCH tab

OSC Pitch
OSC Detune
Pitch Env Attack Time
Pitch Env Decay Time
Pitch Env Depth
Octave Shift
Pitch Bend Range Up
Pitch Bend Range Down

FILTER tab

FILTER Mode
34
OSC tab
Value
OFF, ON
SAW
SQR
PW-SQR
TRI
SINE
NOISE
SUPER SAW (SP-SAW)
PCM
A, B, C
1–450
-6, 0, +6, +12 [dB]
0–127
0–127
0–127
0–127
-24–+24
-50–+50
0–127
0–127
-63–+63
-3–+3
0–+24
0–-24
BYPASS, LPF1, LPF2, LPF3, LPF4, HPF,
BPF, PKG
Explanation
Use these buttons to turn on the partial that you want to be heard .
This waveform contains a sine wave fundamental plus a fixed proportion of sine wave harmonics at
all integer multiples of that fundamental .
This waveform contains a sine wave fundamental plus a fixed proportion of sine wave harmonics at
odd-numbered multiples of that fundamental .
The overtone structure of this waveform will vary significantly depending on the width of the
upper portion of the waveform (Pulse Width) .
This waveform contains a sine wave fundamental plus a fixed proportion of sine wave harmonics at
even-numbered multiples of that fundamental .
This is a sine wave . This is a waveform that produces just a single frequency; it is the basis of all
sound .
This waveform contains all frequencies . It is suitable for percussion instrument sounds or sound
effects .
This produces a tone similar to seven sawtooth waves heard simultaneously . Pitch-shifted sounds
are added to the center sound . It is suitable for strings sounds, and for creating thick sounds .
This is a PCM waveform .
You can select variations of the currently selected WAVE .
*
This has no effect for SP-SAW or PCM .
Selects the PCM waveform .
* This is valid only if PCM is selected for OSC Wave .
Specifies the gain (amplitude) of the waveform .
The value will change in 6 dB (decibel) steps . Each 6 dB increase doubles the gain .
*
This is valid only if PCM is selected for OSC Wave .
Specifies the amount (depth) of LFO applied to PW (Pulse Width) .
If the OSC Wave has selected (PW-SQR), you can use this slider to specify the amount of LFO
modulation applied to PW (pulse width) .
*
If the Ring Switch is on, this has no effect on partials 1 and 2 .
Specifies the pulse width .
If the OSC Wave has selected (PW-SQR), you can use this slider to specify the width of the upper
portion of the square wave (the pulse width) as a percentage of the entire cycle .
Decreasing the value will decrease the width, approaching a square wave (pulse width = 50%) .
Increasing the value will increase the width, producing a distinctive sound .
* If the Ring Switch is on, this has no effect on partials 1 and 2 .
Shifts the range of change . Normally, you can leave this at 127 .
* If the Ring Switch is on, this has no effect on partials 1 and 2 .
Specifies the amount of pitch difference between the seven sawtooth waves layered within a
single oscillator .
*
Higher values will increase the pitch difference . (OSC Detune applies an equal amount of pitch
difference between each of the seven sawtooth waves .)
*
If the Ring Switch is on, this has no effect on partials 1 and 2 .
*
This is valid only if SP-SAW is selected for OSC Wave .
Adjusts the pitch in semitone steps .
Adjusts the pitch in steps of one cent .
Specifies the attack time of the pitch envelope .
This specifies the time from the moment you press the key until the pitch reaches its highest (or
lowest) point .
Specifies the decay time of the pitch envelope .
This specifies the time from the moment the pitch reaches its highest (or lowest) point until it
returns to the pitch of the key you pressed .
This specifies how much the pitch envelope will affect the pitch .
Specifies the octave of the tone .
Specifies the amount of pitch change that occurs when the pitch bend/modulation lever is moved
all the way to the right .
Specifies the amount of pitch change that occurs when the pitch bend/modulation lever is moved
all the way to the left .
Selects the type of filter .