PCM Synth Tone (PCMS) –
Parameter
Control1–4 Dest1–4
Control1–4 Sens1–4
Control1–4 Switch1–4
64
MTRX CTRL1–4 tab
Value
OFF, PITCH, CUTOFF, RESONANCE,
LEVEL, PAN, OUTPUT LEVEL, CHORUS
SEND, REVERB SEND, LFO1/LFO2
PITCH DEPTH, LFO1/LFO2 TVF
DEPTH, LFO1/LFO2 TVA DEPTH,
LFO1/LFO2 PAN DEPTH, LFO1/
LFO2 RATE, PIT ENV A-TIME, PIT ENV
D-TIME, PIT ENV R-TIME, TVF ENV
A-TIME, TVF ENV D-TIME, TVF ENV
R-TIME, TVA ENV A-TIME, TVA ENV
D-TIME, TVA ENV R-TIME, PMT, FXM
DEPTH
-63–+63
OFF, ON, REVS
Explanation
Selects the partial parameter that is to be controlled when using the Matrix Control .
The following parameters can be controlled .
When not controlling parameters with the Matrix Control, set this to
can be specified for each Matrix Control, and controlled simultaneously .
MEMO
In this manual, Parameters that can be controlled using the Matrix Control (p . 63) are marked with a
."
If you're not using Matrix Control
OFF: Matrix Control will not be used .
Changing the Pitch
PITCH: Changes the pitch .
Opening and Closing the Filter
CUTOFF: Changes the cutoff frequency .
RESONANCE: Emphasizes the overtones in the region of the cutoff frequency, adding
character to the sound .
Changing the Volume and Pan
LEVEL: Changes the volume level .
PAN: Changes the pan .
Changing How the Effects Are Applied
OUTPUT LEVEL: Changes the volume of the original sound .
CHORUS SEND: Changes the amount of chorus .
REVERB SEND: Changes the amount of reverb .
Applying LFO to Modulate Sounds
LFO1/LFO2 PCH DEPTH: Changes the vibrato depth .
LFO1/LFO2 TVF DEPTH: Changes the wah depth .
LFO1/LFO2 TVA DEPTH: Changes the tremolo depth .
LFO1/LFO2 PAN DEPTH: Changes the effect that the LFO will have on pan .
LFO1/LFO2 RATE: Changes the speed of the LFO cycles . The speed will not change if LFO Rate
is set to
"note."
Changing the Pitch Envelope
PIT ENV A-TIME: Changes the Env Time 1 of the pitch envelope .
PIT ENV D-TIME: Changes the Env Time 2 and Env Time 3 of the pitch envelope .
PIT ENV R-TIME: Changes the Env Time 4 of the pitch envelope .
Changing the TVF Envelope
TVF ENV A-TIME: Changes the Env Time 1 of the TVF envelope .
TVF ENV D-TIME: Changes the Env Time 2 and Env Time 3 of the TVF envelope .
TVF ENV R-TIME: Changes the Env Time 4 of the TVF envelope .
Changing the TVA Envelope
TVA ENV A-TIME: Changes the Env Time 1 of the TVA envelope .
TVA ENV D-TIME: Changes the Env Time 2 and Env Time 3 of the TVA envelope .
TVA ENV R-TIME: Changes the Env Time 4 of the TVA envelope .
Splitting Partials That Are Played
PMT
If the Matrix Control is used to split partials, set the PMT Velocity Control (p . 53) to
PMT Control Switch (p . 54) to
"ON."
•
If the Matrix Control is used to split partials, we recommend setting the Sens (p . 64) to
Selecting a lower value may prevent switching of the partials . Furthermore, if you want to
reverse the effect, set the value to
•
If you want to use matrix control to switch smoothly between partials, use the Velo Fade Lower and
Velo Fade Upper (p . 54) . The higher the values set, the smoother the switch is between the partials .
Changing the Depth of Frequency Modulation Produced by FXM
FXM DEPTH
Sets the amount of the Matrix Control's effect that is applied .
If you wish to modify the selected parameter in a positive
toward the right, or faster etc . – from its current setting, select a positive
If you wish to modify the selected parameter in a negative
the left, or slower etc . – from its current setting, select a negative
negative settings, greater absolute values will allow greater amounts of change .
Set this to
"0"
if you don't want to apply the effect .
Selects the partial to which the effect is applied when using the Matrix Control .
OFF: The effect will not be applied .
ON: The effect will be applied .
REVS: The effect will be applied in reverse .
"OFF."
"-63."
"+"
direction – i .e ., a higher value,
"+"
"-"
direction – i .e ., a lower value, toward
"-"
value . For either positive or
Up to four parameters
"
"OFF,"
and the
"+63."
value .