Playing The Input Source - Denon AVR-3801 Operating Instructions Manual

Playing the input source

1 Select the input source to be played.
Example: CD
FUNCTION
(Main unit)
To select the input source when REC
MULTI OUT or TUNING PRESET is
selected, press the SOURCE button
then operate the input function
selector.
2 Select the input mode.
• Selecting the analog mode
Press the ANALOG button to switch to the analog input.
ANALOG
(Main unit)
• Selecting the external input (EXT. IN) mode
Press the EXT. IN (on the EXT. IN button on the remote
control unit) to switch the external input.
EXT.IN
(Main unit)
• Selecting the AUTO, PCM and DTS modes
The mode switches as shown below each time the INPUT
MODE button is pressed.
AUTO
• Selecting the AUTO mode
Press the AUTO button to switch to the auto mode.
42
CD
3
(Remote control unit)
SOURCE
(Main unit)
ANALOG
(Remote control unit)
EXT.IN
(Remote control unit)
PCM DTS
MODE
(Remote control unit)
AUTO
(Main unit)
TV CD
VCR DBS/CABLE
DISPLAY
SURR.
PARA.
SETUP
BAND
CHANNEL
+
SKIP
-
SKIP
TUNER
1
CDR/ TAPE
4
VCR-1 VCR-2 /V.AUX
7
TV/
VCR
TEST
TONE
SURROUND
DOLBY/DTS
SURROUND
6.1 / 7.1
SURROUND
MODE
SYSTEM CALL
CALL 1
Input mode selection function
Different input modes can be selected for the different input sources.
The selected input modes for the separate input sources are stored in
the memory.
q AUTO (auto mode)
In this mode, the types of signals being input to the digital and
analog input jacks for the selected input source are detected and
the program in the AVR-3801's surround decoder is selected
automatically upon playback. This mode can be selected for all
input sources other than PHONO and TUNER.
The presence or absence of digital signals is detected, the signals
input to the digital input jacks are identified and decoding and
playback are performed automatically in DTS, Dolby Digital or PCM
(2 channel stereo) format. If no digital signal is being input, the
analog input jacks are selected.
Use this mode to play Dolby Digital signals.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM signals are
being input.
Note that noise may be generated when using this mode to play
signals other than PCM signals.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS signals are
being input.
r ANALOG (exclusive analog audio signal playback mode)
The signals input to the analog input jacks are decoded and played.
t EXT. IN (external decoder input jack selection mode)
The signals being input to the external decoder input jacks are
played without passing through the surround circuitry.
NOTE:
• Note that noise will be output when CDs or LDs recorded in DTS
format are played in the "PCM" (exclusive PCM signal playback) or
"ANALOG" (exclusive PCM signal playback) mode. Select the
AUTO or DTS mode when playing signals recorded in DTS from a
laser disc player or CD player.
Note on playing a source encorded with DTS
• Noise may be generated at the beginning of playback and
while searching during DTS playback in the AUTO mode. If
so, play in the DTS mode.
CDR/MD/ TAPE RECEIVER
1
VDP DVD
MENU
OSD
RETURN
TUNING
A/B
MEMORY
MODE
VOLUME
TUNING
+
ENTER
4
-
SHIFT
MUTING
PHONO CD
2 3
VDP DVD
5 6
TV/DBS
8 9
0 +10
SPEAKER OUTPUT
DSP 5CH / 7CH
SIMU. STEREO
3
DIRECT STEREO
INPUT
2
ANALOG EXT.IN
CALL 2 BACKLIGHT