Weld Output Terminals And Selecting Cable Sizes - Miller Auto Continuum 500 Owner's Manual

5-2. Weld Output Terminals And Selecting Cable Sizes*

NOTICE − The Total Cable Length in Weld Circuit (see table below) is the combined length of both weld cables. For example, if the power source is
100 ft (30 m) from the workpiece, the total cable length in the weld circuit is 200 ft (2 cables x 100 ft). Use the 200 ft (60 m) column to determine cable
size.
100 ft (30 m) or Less
10 − 60%
Duty
Welding
Cycle
Amperes
2
AWG (mm )
100 4 (20)
150 3 (30)
200 3 (30)
250 2 (35)
300 1 (50)
350 1/0 (60)
400 1/0 (60)
500 2/0 (70)
600 3/0 (95)
This chart is a general guideline and may not suit all applications. If cable overheats, use next size larger cable.
*
**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.
2
( ) = mm for metric use
***For distances longer than those shown in this guide, see AWS Fact Sheet No 39, Welding Cables, available from the American Welding
Society at http://www.aws.org.
Notes
Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit
150 ft
(45 m)
60 − 100%
Duty Cycle
2
AWG (mm )
4 (20) 4 (20)
3 (30) 2 (35)
2 (35) 1 (50)
1 (50) 1/0 (60)
1/0 (60) 2/0 (70)
2/0 (70) 3/0 (95)
2/0 (70) 3/0 (95)
3/0 (95) 4/0 (120)
4/0 (120) 2x2/0 (2x70)
Not Exceeding***
200 ft 250 ft
(60 m) (70 m)
10 − 100% Duty Cycle
AWG (mm
3 (30) 2 (35)
1 (50) 1/0 (60)
1/0 (60) 2/0 (70)
2/0 (70) 3/0 (95)
3/0 (95) 4/0 (120)
4/0 (120) 2x2/0 (2x70)
4/0 (120) 2x2/0 (2x70)
2x2/0 (2x70) 2x3/0 (2x95)
2x3/0 (2x95) 2x4/0 (2x120)
300 ft 350 ft
(90 m) (105 m)
2
)
1 (50) 1/0 (60)
2/0 (70) 3/0 (95)
3/0 (95) 4/0 (120)
4/0 (120) 2x2/0 (2x70)
2x2/0 (2x70) 2x3/0 (2x95)
2x3/0 (2x95) 2x3/0 (2x95)
2x3/0 (2x95) 2x4/0 (2x120) 2x4/0 (2x120)
2x4/0 (2x120) 3x3/0 (3x95)
3x3/0 (3x95) 3x4/0 (3x120) 3x4/0 (3x120)
Ref. S-0007-L 2017−08
OM-277115 Page 17
400 ft
(120 m)
1/0 (60)
3/0 (95)
4/0 (120)
2x2/0 (2x70)
2x3/0 (2x95)
2x4/0 (2x120)
3x3/0 (3x95)