Roland VersaEXPRESS RF-640 Service Notes page 183

FRHDPULWwC
SERVICE MENU
SENSOR CHECK L
This menu displays the real-time status of each sensor.
The first page shows the status of each sensor. Each alphabet stands for as follows.
F : Front Paper Sensor
R : Rear Paper Sensor
H : Head Lock Sensor
D : Maintenance Cover R Sensor
P : Maintenance Cover L Sensor
U : Head UP/Down Sensor
L : Sheet Load Sensor
W : Paper Side Sensor
w : Wiper Sensor
C : Front Cover Sensor
SERVICE MENU THERMISTOR CHK
THERMISTOR CHK HEAD:25 C/ 77 F
SERVICE MENU
SUB MENU
SUB MENU
SERIAL NO.
SUB MENU
CHANGE INKTYPE
[In the case of MAX2 4C]
SUB MENU
FILL INK
CARTRIDGE
SLOT 8
RF-640A has until SLOT4.
12345678
EC
＊ ＊ *
It shows [ ＊ ] when there is a media.
It shows [ ＊ ] when there is a media.
It shows [ ＊ ] when the head is at lock position.
It shows [ ＊ ] when the cover is open.
It shows [ ＊ ] when the cover is open.
It shows [ H ] when the Head is HIGH,
it shows [ L ] when the Head is LOW.
It shows [ ＊ ] when the pich lever is down.
It shows [ ＊ ] when the wiper is on a media.
It shows [ ＊ ] when the wiper is at origin positon.
It shows [ ＊ ] when the cover is open.
This is for checking Thermistor. It displays the temperature read from the thermistor placed on the each board.
The temperature on the left is in Celsius and the right is in Fahrenheit.
Since the temperature of the device possibly rises, it normally shows higher temperature than the room temperature.
SERIAL NO.
ZA0000
CHANGE INKTYPE
UNKNOWN
This is for changing the Ink Type. Different from the process
in the User Menu, operations such as Head Wash and Fill
Ink are not included.
This menu is used as a correction purpose when a wrong-type
ink is selected.
EMPTY
DRAIN BOTTLE
※When the cartridge is inserted.
REMOVE CARTRIDGE
12345678
FILLING
>
FILLING
>>
REMOVE SOL CL
12345678
FILLING
>>
If it does not need cleaning.
SET SOL CRT.
2 4 6 8
FILLING
>>>>>>>>>>
It reads the information written on the IC of each carriage.
Following messages are displayed when some error is found.
Ink cartridge is not inserted
SLOT1
NO CARTRIDGE
A cartridge with no IC is inserted
SLOT1
NO IC CHIP
System error due to the trouble such as a damage of driver IC placed on Ink Tank Board
SLOT1
SYSTEM ERROR
Data error
SLOT1
DATA ERROR
This menu is for entering the Serial No. of the machine in seven digits. The cursor moves
between digits with [ ] and [
To Setup View
Ink Type PIGMENT 4COLOR
PIGMENT 6 COLOR
※It is selectable if the System Switch is16-1 with RF-640.
PIGMENT 8 COLOR
UNKNOWN : No Ink installed.
SELECT INK TYPE
E-SOL MAX2 4C
If it needs cleaning,
go to the next sequence,
if it doesn't ,
go to the sequence which
has [＊] mark.
EMPTY
INK...
DRAIN BOTTLE
SET SOLCL-LIQUID
INK...
12345678
FILLING INK...
>>
INK... EMPTY
DRAIN BOTTLE
FILLING INK...
>>>>>>>>>>
INK... EMPTY
DRAIN BOTTLE
4-4
The second page shows the status of each
Cartridge Sensor and Ink Empty Sensor.
Blank: Cartridge not inserted, Ink remains
C: Cartridge inserted, Ink remains
E: Cartridge not inserted, Ink empty
＊ : Cartridge inserted, Ink empty
Setup will be canceled when it out of the sensor check menu.
] keys. The parameter can be changed with [
※It is selectable if the System Switch is16-1 with RF-640.
INSTALL
DRAIN BOTTLE
When it needs cleaning.
SET SOLCL-LIQUID
12345678
REMOVE SOL CL
12345678
FILLING INK...
>>>
SET SOLCL-LIQUID
12345678
REMOVE SOL CL
12345678
SET SOL CRT.
1 3 5 7
FILLING INK...
>>>>>>>>>>
] and [ ] keys.