Ftp Access Via Ms-Dos - ABB SM3000 User Manual

SM3000
Multipoint Videographic Recorder
E.3.1 FTP Access via MS-DOS
To use FTP access:
1. If the DOS window is not open, click the 'Start' button on
the task bar and select 'Run'.
2. Type 'ftp' and press Enter. The 'ftp>' prompt is displayed.
3. In the 'Open:' field, type 'cmd' and click the 'OK' button.
A DOS window is displayed with the cursor at the default
drive prompt.
4. Type 'open' followed by the IP address assigned to the
recorder and press Enter. If connection is successful, a
confirmation message is displayed, for example, the
following is displayed for a device with IP address
192.168.1.1:
Connected to 192.168.1.1
220 WinCE GkWare FTP Service (Version 1.3 May 6
2003)
User (192.168.1.1: (none)):
5. Enter the FTP User name for the recorder (see Section
6.4.5, page 69) and press Enter. The following is
displayed:
331 OK, password required
Password:
6. Type the device password and press Enter. If the user has
full access, the following is displayed:
230 OK
ftp>
If the user has read-only access, the following is
displayed:
230 OK, Read-only access granted
ftp>
Note.
n When typing the password, the cursor does not
move and nothing appears in the DOS window.
n An audit log entry is created for each FTP logon
giving details of the logon user name and type of
access (full or read-only), e.g:
The link is now open.
178
The following FTP commands are used to communicate with
the recorder:
Cd Change directory on the server
Close Terminate the data connection
Del Delete a file on the server
Dir Display the server directory
Get Get a file from the server
Help Display help
Ls Lists contents of the remote directory
Mget Get several files from the server
Mput Send several files to the server
Open Connect to the server
Put Send a file to the server
Pwd Display the current server directory
Quote Supply an internal FTP command directly
Quit Terminate the FTP session
For example, to view the contents of the root directory, type 'dir'
at the ftp prompt and press Enter. A list of folders is displayed:
ftp> dir
200 PORT command successful.
150 Opening ASCII mode data connection for /bin/ls.
01-01-1998 12:00PM
01-01-1998 12:00PM
10-03-2003 12:59PM
10-03-2003 12:59PM
10-03-2003 12:59PM
10-03-2003 12:59PM
10-03-2003 12:59PM
226 Transfer complete.
ftp: 348 bytes received in 1.03Seconds 0.34Kbytes/sec.
To view the contents of a folder, type 'cd [Folder Name]' and
press Enter, then type 'dir' and press Enter. A similar list is
displayed showing the contents of the folder.
Note. The contents of the Storage_Card folder are
accessible only if archiving is set to 'On-line' in the
recorder's Setup menu – see Section 5.4, page 43.
To copy a file from the recorder to the PC's local or network
drive, type:
get '[File name]'
...at the ftp prompt and press Enter. A confirmation such as the
following is displayed:
ftp> get'14083218Sep03Ch1_4AnlgSM3000.B00'
200 PORT command successful.
150 Opening ASCII mode data connection for
14083218Sep03Ch1_4AnlgSM3000.B00
226 RETR command successful.
ftp: 75912 bytes received in 1.38 Seconds 55.21
Kbytes/sec.
ftp>
Appendix E – Ethernet
<DIR> Flash_Disk
<DIR> Storage_Card
<DIR> www
<DIR> My Documents
<DIR> Program Files
<DIR> Temp
<DIR> Windows
IM/SM3000–EN Rev. L