Enter User Codes - NAPCO GEMINI GEM-P3200 Programming Instructions Manual

WI818B 5/99
User# User Code

number buttons
Press the ( ) button once to set the cursor to the User Code. Use the number buttons
enter a code of up to 6 digits. Enter up to 6 digits (4 digits is recommended) in the first six boxes from left to right for
each user code. Valid entries are: 0-9. Note: Press the
blank (•) any trailing boxes. If an "Ambush Code" (Address 0495) is entered, do not program the first two digits of ANY
User Code as the same digits entered for the "Ambush Code".

If the programmed code is less than 6 digits, press the
Refer to the tables below for the available User Option and User Level data entries. Enter the user options data in the
left digit. Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than 9,
press the
For Keypad Access Control, press the
below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–8 data in
the left digit. (Press the
Example: Enter a code of "123456" as
"123456".
USER OPTIONS
DATA BLOCKED USER BYPASS
ENTRIES VIEW PROGRAM
blank (•) DISABLED
1 Y
2 Y
3 Y Y
4 Y
5 Y Y
6 Y Y
7 Y Y Y
8
9 Y
0 Y
B Y Y
C Y
D Y Y
E Y Y
F Y Y Y
Note: "Y" indicates option is enabled.
Note: Users are assigned to areas in "Enable User Code by Area" (Address 2500-2531) in Direct Address Programming.
NAPCO Security Systems
Option Access
Enter User Codes (Press the (
/Level Control
For default program, enter up to 16 User Codes: up to 8 for Area 1 (Users
01–08) and up to 8 for Area 2 (Users 09–16), with an Authority Level and
Access Control Options (if necessary) for each code, as follows. Note: Up to
32 users are available using Direct Address Program Mode.
Press the (
through to enter the User Number.


buttons through the
button once again to program applicable keypads. Refer to the tables
buttons for blank.)
USER CODE
(UP TO 6 DIGITS)
1 2 3 4 5 6
DATA AUTHORITY
ENTRIES LEVEL
OVERVIEW
blank (•) NONE
1 LEVEL 1
2 LEVEL 2
3 LEVEL 3
4 NONE
5 LEVEL 1
6 LEVEL 2
7 LEVEL 3
8 NONE
Y 9 LEVEL 1
Y 0 LEVEL 2
Y B LEVEL 3
Y
Y
Y
Y
Y


) button to set the cursor to the User Number. Use the

button for a zero. No blank spaces in between; leave
button once to set the cursor to the OPTION/LEVEL.
buttons for B through F, respectively.
USER OPTIONS
USER USER ACCESS CONTROL
OPTION LEVEL KEYPADS
CODE ACCESS CONTROL KEYPADS
TYPE
DATA K.P. 5 K.P. 6
ENTRIES
ARM/DISARM
ARM/DISARM
blank (•) NONE
ARM/DISARM
1 Y
ARM/DISARM
2 Y
ARM ONLY
3 Y Y
ARM ONLY
4
ARM ONLY
5 Y
ARM ONLY
6 Y
SERVICE
7 Y Y
SERVICE Note: "Y" indicates option is
enabled.
SERVICE
SERVICE
GEM-P3200 Programming Instructions
) button to set cursor.)
through
ACCESS CONTROL KEYPADS
K.P. 7 DATA K.P. 1 K.P. 2 K.P. 3 K.P. 4
ENTRIES
blank (•) NONE
1 Y
2 Y
3 Y Y
Y 4 Y
Y 5 Y Y
Y 6 Y Y
Y 7 Y Y Y
8
9 Y
0 Y
B Y Y
C Y
D Y Y
E Y Y
F Y Y Y
Note: "Y" indicates option is enabled.
Page 7
to
Y
Y
Y
Y
Y
Y
Y
Y