Enable Burg Output Chirp On Keyfob; Enable Sia Cp-01 Features; Number Of Keypads In Area 1; Central Station Receiver 1 Telephone Number - NAPCO Gemini GEM-P816 Programming Instructions Manual

!
Page 8
Enable Burg Out
Chirp? Y/N
(Press YES or NO)
Enable SIA CP-01?
Y/N
(Press YES or NO)
# Area 1 Keypads
Enter # KPs 01
(Direct Entry)
Central Phone #
(Direct Entry)
Central Station
Account # (____)
(Direct Entry)
S e e W I f o r I n f o
R c v r F o r m a t ( 0 )
(Direct Entry)
E n t e r u s e r c o d e
U 0 1 1 2 3 - 9 -
User# User Code Area 1 Area 2
tions. For Area 2 Options, press the
•
If "Enable Global Ambush Code" (Address 0720) is enabled and "Global Ambush Code" (Address 1054) is not left blank (•), do not program the
first two digits of ANY User Code the same as the "Global Ambush Code".
U
•
Press to save. Note: Duplicate User Codes are not allowed; therefore a duplicate Code entered in the LCD Window will erase when
pressed. To proceed to the next User Code, press
the NEXT/YES button to proceed.
USER OPTIONS
USER CODE AREA 1
OPTIONS
(UP TO 6 DIGITS)
X
GEM-P816 Programming Instructions

Enable Burg Output Chirp on KeyFob?

•
Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.
•
Press the PRIOR/NO button to continue.
NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.

Enable SIA CP-01 Features?

•
Press the NEXT/YES button to enable.
•
Press the PRIOR/NO button to continue.
The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not
enable unless reporting, otherwise system trouble Fail to Communicate may occur.

Number of Keypads in Area 1

•
Enter the total number of Keypads to be installed in Area 1.
•
Valid entries are from 01 to 07. Directly enter the number of keypads, including leading zeros.
U
Press to save. Press the NEXT/YES button to proceed.
NOTE: Area 2 keypads must be assigned in Direct Address Programming. See Keypad Options.

Central Station Receiver 1 Telephone Number

•
Enter telephone number of up to 16 digits.
•
Press through
1
•
Press through
G 1
•
Pre-Dial Delay = "D" (
•
U
Press to save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Ad-
dress Programming. See CS Receiver Options.

Central Station Receiver 1 Account Number

•
Enter an account number of up to four digits.
•
Press through
0
• U
Press to save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Account Numbers
must be entered in Direct Address Programming. See CS
Reporting Options.

Central Station Receiver 1 Format

•
From the table at the right enter the receiver format.
•
Press through
0 9
•
Press through
G1
• U
Press to save and press the NEXT/YES button to proceed.
Enter User Codes (Press
For default program, enter up to 32 User Codes, with Area 1 and Area 2 Options.
•
Press the ( ) button once to set the cursor to the User Code.
R
•
Press through
0 9
•
Press to set the cursor to the Area 1 Options Level. Refer to the table below for available op-
R
button once again.
R
to set the cursor to the User Number and change it using the number buttons. Press
R
USER AREA OPTIONS
DATA ENTRIES
AREA 2
L
OPTIONS
blank(•) blank
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•) Add 8
for digits 1–9;
9 G 0
for letters B–F, respectively.
G 5
); Dial-Tone Detection = "E" (
G 4
for digits 0–9, and
9 G 0
, and for blank (•).
G0
for letters B–E.
G4
to set cursor.)
R
to enter a code from 3 to 6 digits, leave blank (•) any trailing boxes.
OPTION
ENABLED
R
Disabled
1 Arm/Disarm
2 Arm Only
3 Service
4 Access
5 Ambush
* User Program
WI995C 2/04
for a zero and for a blank (•).
0
).
G 5
for a blank (•).
DATA CS RECEIVER 1 FORMAT
ENTRY
• Ademco Slow, Silent Knight
(blank) Slow
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
5 Universal High Speed
B SIA
C Ademco Point ID
E Pager
Example: Program a code of "2222" for user
02, with area 1 options of "Arm/Disarm" and
"User Program". Enter "2222" for a user code,
"• (blank) 9" for area 1 options and "• (blank) •
(blank)" for area 2 options.
L
NAPCO Security Systems
U
is