Enable Burg Output Chirp On Keyfob; Enable Sia Cp-01 Features; Number Of Keypads In Area 1; Central Station Receiver 1 Telephone Number - NAPCO Gemini GEM-P816 Programming Instructions Manual

Page 8
Enable Burg Out
Chirp?
(Press YES or NO)
Enable SIA CP-01?
(Press YES or NO)
# Area 1 Keypads
Enter # KPs
(Direct Entry)
Central Phone #
(Direct Entry)
Central Station
Account # (____)
(Direct Entry)
S e e W I f o r I n f o
R c v r F o r m a t
(Direct Entry)
E n t e r u s e r c o d e - >
U 0 1 1 2 3 - 9 -
User# User Code Area 1
•
If "Enable Global Ambush Code" (Address 1422) is enabled and "Global Ambush Code" (Address 2045) is not left blank (•), do not program the
first two digits of ANY User Code the same as the "Global Ambush Code". See Address 2045 further in this manual for more information.
• U
Press to save. Note: Duplicate User Codes are not allowed; therefore a duplicate Code entered in the LCD Window will erase when
pressed. To proceed to the next User Code, press
the NEXT/YES button to proceed.
USER OPTIONS
USER CODE
(UP TO 6 DIGITS)
GEM-P816 Programming Instructions

Enable Burg Output Chirp on Keyfob?

•
Press the NEXT/YES button to enable Burg Output Chirp on Keyfob Arm / Disarm.
Y/N
•
Press the PRIOR/NO button to continue.
NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.

Enable SIA CP-01 Features?

•
Press the NEXT/YES button to enable.
Y/N
•
Press the PRIOR/NO button to continue.
The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not
enable unless reporting, otherwise system trouble Fail to Communicate may occur.

Number of Keypads in Area 1

•
Enter the total number of Keypads to be installed in Area 1.
01
•
Valid entries are from 01 to 07. Directly enter the number of keypads, including leading zeros.
U
Press to save. Press the NEXT/YES button to proceed.

Central Station Receiver 1 Telephone Number

•
Enter telephone number of up to 16 digits.
•
Press through
1
•
Press
G 1
•
Pre-Dial Delay = "D" (
• U
Press to save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Ad-
dress Programming. See CS Receiver Options.

Central Station Receiver 1 Account Number

•
Enter an account number of up to four digits.
•
Press through
0
• U
Press to save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Account Numbers
must be entered in Direct Address Programming. See CS
Reporting Options.

Central Station Receiver 1 Format

•
From the table at the right enter the receiver format.
( 0 )
•
Press through
0
•
Press
G1
• U
Press to save; press the NEXT/YES button to proceed.
Enter User Codes (Press
For default program, enter up to 16 User Codes, with Area 1 Options.
•
Press the (
R
•
Press through
0
•
Press to set the cursor to the Area 1 Options Level. Refer to the table below for available
R
options.
R
AREA 1
OPTIONS
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
for digits 1–9;
9
through
G 5
); Dial-Tone Detection = "E" (
G 4
for digits 0–9, and
9
, and
9 G0
through for letters B–E.
G4
to set cursor.)
R
) button once to set the cursor to the User Code.
to enter a code from 3 to 6 digits, leave blank (•) any trailing boxes.
9
to set the cursor to the User Number and change it using the number buttons. Press
USER AREA OPTIONS
DATA ENTRIES
OPTION
ENABLED
L R
blank(•) Disabled
1 Arm/Disarm
2 Arm Only
3 Service
4 Access
5 Ambush
Add 8 * User Program
4 blank(•) Bypass Enable
for a zero and
G 0
for letters B–F, respectively.
G 5
for a blank (•).
G 0
DATA CS RECEIVER 1 FORMAT
ENTRY
• Ademco Slow, Silent Knight
(blank)
2
3
for blank (•).
4 Radionics, DCI, Franklin Slow
5
B
C
E
Example: Program a code of "2222" for user
02, with area 1 options of "Arm/Disarm" and
"User Program". Enter "2222" for a user code,
"• (blank) 9" for area 1 options.
NAPCO Security Systems
R
for a blank (•).
0
).
Slow
Radionics Fast
Silent Knight Fast
Universal High Speed
SIA
Ademco Point ID
Pager
U
is