Table of Contents
Advertisement
WI1502A 9/06
Central Phone #
(Direct Entry)
Central Station
Account # (____)
(Direct Entry)
S e e W I f o r I n f o
R c v r F o r m a t
( 0 )
(Direct Entry)
E n t e r u s e r c o d e - >
U 0 1 1 2 3
- 9 -
User#
User Code
Area 1 Area 2
USER OPTIONS
USER CODE
AREA 1
AREA 2
OPTIONS
OPTIONS
(UP TO 6 DIGITS)
L
NAPCO Security Systems
Central Station Receiver 1 Telephone Number
•
Enter telephone number of up to 16 digits.
•
Press
through
1
•
Press
G 1
•
Pre-Dial Delay = "D" (
•
U
Press
to save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Ad-
dress Programming. See CS Receiver Options.
Central Station Receiver 1 Account Number
•
Enter an account number of up to four digits.
•
Press
through
0
•
U
Press
to save and press the NEXT/YES button to proceed.
NOTE: Central Station Receiver 2 and 3 Account Numbers must be entered in Direct Ad-
dress Programming. See CS Reporting Options.
Central Station Receiver 1 Format
•
From the table at the right enter the receiver format.
•
Press
through
0
•
Press
G1
•
U
Press
to save and press the NEXT/YES button to proceed.
Enter User Codes (Press
For default program, enter up to 64 User Codes, with Area 1, 2, 3 & 4 Options.
•
Press the (
) button once to set the cursor to the User Code.
R
•
Press
through
0
•
Press
to set the cursor to the Area 1 Options Level. Refer to the table below for available
R
options. For Area 2 Options, press
and fourth time.
•
If "Enable Global Ambush Code" (Address 1422) is enabled and "Global Ambush Code" (Address
2045) is not left blank (•), do not program the first two digits of ANY User Code the same as the
"Global Ambush Code". See Address 2045 further in this manual for more information.
U
•
Press
to save. Note: Duplicate User Codes are not allowed; therefore a duplicate Code en-
tered in the LCD Window will erase when
to set the cursor to the User Number and change it using the number buttons. Press the
R
NEXT/YES button to proceed.
DATA ENTRIES
L
AREA 3
AREA 4
blank(•)
OPTIONS
OPTIONS
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
4
Example: Program a code of "2222" for user 02, with area 1 options of "Arm/
Disarm" and "User Program". Enter "2222" for a user code,
"• (blank) 9" for area 1 options and "• (blank) •(blank)" for area 2 options.
for digits 1–9;
9
G 0
through
for letters B–F, respectively.
G 5
); Dial-Tone Detection = "E" (
G 4
for digits 0–9, and
9
, and
for blank (•).
9
G0
through
for letters B–E.
G4
to set cursor.)
R
to enter a code from 3 to 6 digits, leave blank (•) any trailing boxes.
9
once again. For Area 3 & 4 Options, press
R
U
is pressed. To proceed to the next User Code, press
USER AREA OPTIONS
OPTION
ENABLED
R
blank(•)
Disabled
1
Arm/Disarm
2
Arm Only
3
Service
4
Access
5
Ambush
Add 8
* User Program
blank(•)
Bypass Enable
Freedom F-64 Programming Instructions
for a zero and
0
G 5
for a blank (•).
G 0
DATA
CS RECEIVER 1 FORMAT
ENTRY
•
Ademco Slow, Silent Knight
(blank)
Slow
2
Radionics Fast
3
Silent Knight Fast
4
Radionics, DCI, Franklin Slow
5
Universal High Speed
B
SIA
C
Ademco Point ID
E
Pager
Page 9
for a blank (•).
).
a third
R
Advertisement
Table of Contents
