Installing Optional Mini-Gbics - Enterasys Matrix 7GR4202-30 Hardware Installation Manual

Installing Optional Mini-GBICs

This section describes how to install a Mini‐GBIC in any of the 7GR4270‐12 front panel ports (1‐12)
or the 7GR4280‐19 front panel ports (1‐18) or in an optional NEM. For a list of supported
Mini‐GBICs and their specifications, refer to "Mini‐GBIC Input/Output Specifications" on
page A‐3.
Preparation
Before installing the Mini‐GBIC, proceed as follows:
1. Attach the antistatic wrist strap (refer to the instructions in the antistatic wrist strap package)
before removing the Mini‐GBIC from the antistatic packaging.
2. Remove the Mini‐GBIC from the packaging.
3. If there is a protective dust cover (see in Figure 3‐1 or Figure
not remove it at this time.
Installation
To install a Mini‐GBIC with an MT‐RJ connection, refer to Figure
Figure 3‐2, or for an RJ45 connection, refer to Figure
1. Hold the Mini‐GBIC with its top side facing up and its 7‐pin edge connector facing the port
slot.
2. Carefully align the Mini‐GBIC with the port slot.
3. Push the Mini‐GBIC into the port slot until the Mini‐GBIC "clicks" and locks into place.
Warning: Fiber-optic Mini-GBICs use Class 1 lasers. Do not use optical instruments to view the
laser output. The use of optical instruments to view laser output increases eye hazard. When
viewing the output optical port, power must be removed from the network adapter.
Advertencia: Los Mini-GBICS de fibra optica usan lasers de clase 1. No se debe usar
instrumentos opticos para ver la potencia laser El uso de los instrumentos opticos para ver la
potencia laser incrementa el riesgo a los ojos. Cuando vean el puerto de la potencia optica, la
corriente debe ser removida del adaptador de la red.
Warnhinweis: Mini-GBICs mit Fiber-Optik Technologie benutzen Laser der Klasse 1. Benutzen sie
keinesfalls optische Hilfsmittel, um die Funktion des Lasers zu überprüfen. Solche Hilfsmittel
erhöhen die Gefahr von Sehschäden. Wenn sie den optischen Port überprüfen möchten stellen Sie
sicher, dass die Komponente von der Spannungsversorgung getrennt ist.
Caution: Carefully follow the instructions in this manual to avoid damaging the Mini-GBIC, NEM,
and DFE module.
The Mini-GBIC, NEM, and DFE module are sensitive to static discharges. Use an antistatic wrist
strap and observe all static precautions during this procedure. Failure to do so could result in
damage to the Mini-GBIC, NEM, and DFE module. Always leave the Mini-GBIC in the antistatic bag
or an equivalent antistatic container when not installed.
Precaución: Siga las instrucciones del manual para no dañar el Mini- GBIC, NEM ni el módulo
DFE, puesto que son muy sensible a las descargas de electricidad estática.
Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este
procedimiento. Si no lo hace, podría dañar el Mini- GBIC, NEM o el módulo DFE. Mientras no esté
instalado, mantenga el Mini- GBIC en su bolsa antiestática o en cualquier otro recipiente
antiestático.

Installing Optional Mini-GBICs

3‐2) on the Mini‐GBIC port, do
3‐1, for an LC connection, refer to
3‐3, and proceed as follows:
Matrix DFE-Diamond Series Installation Guide 3-3