Datamax M-Class Mark II Operator's Manual page 38

HF SETTI NGS *
TAG TYPE
AFI VALUE
AFI LOCK
DSFI D VALUE
DSFI D LOCK
EAS VALUE
AUDI O
I NDI CATOR
ERASE ON
FAULT
UHF SETTI NGS *
TAG TYPE
TAG DATA
SI ZE
POWER
ADJUST
KI LL CODE
ACCESS
CODE
GEN 2 LOCK
ACTI ON
LOCK AFTER
WRI TE *
ENABLED
DI SABLED
RETRY
ATTEMPTS *
( 0 - 9)
3
PERFORM
CALI BRATI ON *
YES
NO
Ch a pt e r 4 – M e n u Syst e m
Set s HF t ag param et ers, as follows:
Set s t he t ag t ype:
I SO 15693 ( I s t he default set t ing.)
TI
PHI LI PS
ST LRI 512
ST LRI 64
Applicat ion Fam ily I dent ifier value ( 00 - FF) , where 00 is t he default value.
Applicat ion Fam ily I dent ifier lock ( ENABLED / DI SABLED) , where DI SABLED is t he
default set t ing.
Dat a St orage Form at I dent ifier ( 00 - FF) , where 00 is t he default value.
Dat a St orage Form at I dent ifier lock ( ENABLED / DI SABLED) , where DI SABLED is
t he default set t ing.
Elect ronic Art icle Surveillance value ( 00 - FF) , where 00 is t he default value.
Cont rols t he buzzer ( ENABLED / DI SABLED) , where DI SABLED is t he default
set t ing.
Erases t he t ag when errors are det ect ed ( ENABLED / DI SABLED) , where DI SABLED
is t he default set t ing.
Set s UHF t ag param et ers, as follows:
Set s t he t ag t ype:
EPC 0
EPC 0+ MATRI CS
EPC 0+ I MPI NJ
EPC 1
UCODE EPC 1.19
EM 4022/ 1222
GEN 2 ( I s t he default set t ing.)
Set s t he t ag dat a size:
96- BI T ( I s t he default set t ing.)
64- BI T
Adj ust s t he applied power.
Code used t o perm anent ly deact ivat e t he device:
B3 B2 B1 B0
00 00 00 00 ( I s t he default set t ing.)
Code used t o prot ect t he m em ory cont ent s:
B3 B2 B1 B0
00 00 00 00 ( I s t he default set t ing.)
Set s t he lock level ( NONE, PERMALOCK, PWD- READ/ WRI TE, BOTH) , where NONE is
t he default set t ing.
Locks t he t ag aft er program m ing.
The t ag will be locked.
No locking occurs ( default set t ing) .
Set s t he num ber of ret ry at t em pt s, where:
Zero t o nine are t he num ber of ret ries; and,
I s t he default set t ing.
Allows t he print er t o est ablish t he t ag t o t ransducer dist ance set t ing and nom inal
RFI D power requirem ent s.
I nit iat es t he process. The CALI BRATI NG RFI D m essage will appear as t he print er
feeds m edia t o begin scanning for t he RFI D t ag locat ion. Once t he locat ion is
est ablished, power calibrat ion begins. Upon com plet ion, t he m edia will be ret ract ed
t o t he TOF posit ion; t he calibrat ed posit ion and power result s ( along wit h a brief
SUCCESS or FAI LURE m essage) will be displayed; and, t he print er's dat abase will
be updat ed wit h t he new calibrat ion param et ers.
Term inat es t he process.
3 2