Table of Contents
Advertisement
EQ MODULE
TYPE
3BandEQ
Three-band equalizer.
Explanation of EQ MODULE parameters
Parameter name
Range
HIGH
-12 – 12
MID
-12 – 12
LOW
-12 – 12
LEVEL
ZNR MODULE
TYPE
ZNR
Zoom's proprietary noise reduction that minimizes noise when you are not playing.
*For an explanation of the parameters, refer to the DUAL algorithm.
VOL PDL MODULE
TYPE
VOL PDL
You can use an expression pedal to control the volume.
MODULATION/DELAY MODULE
TYPE
CHORUS
Stereo chorus with clear sound and great spaciousness.
FLANGER
An effect that adds a pronounced character and modulation to the sound.
PHASER
An effect that adds a swooshing modulation to the sound.
TREMOLO
An effect that cyclically varies the volume.
PDL-WAH
An effect that lets you use an expression pedal to control wah manually.
AutoWah
An effect in which wah is applied according to your playing dynamics.
PITCH
An effect that modifies the pitch of the original sound.
RingMod
An effect that produces a metallic resonance.
EXCITER
An effect that gives the sound more focus and spatial definition.
AIR
Simulates the effect of air on the room resonance, giving the sound spatial depth.
WIDE
An effect that produces the sound of a stereo recording made with two mics.
DELAY
A delay effect with a maximum of 500 mSec.
Explanation of MODULATION/DELAY MODULE parameters
Parameter name
DEPTH
RATE
MIX
TYPE = FLANGER : -10 – 10
FB
TYPE = DELAY : 0 – 10
POSITION
COLOR
CLIP
TYPE = PDL-WAH : 1 – 50
FREQ
TYPE = EXCITER : 1 – 5
LEVEL
RTM
FLT TYPE
RESO
SENS
SHIFT
TONE
BALANCE
LowBoost
SIZE
TYPE = WIDE : 1 – 64
TIME
TYPE = DELAY : 1 – 50
WET LVL
DRY LVL
ZOOM MRS-1266
PARAMETER 1
HIGH
Boosts/cuts the high-frequency range.
Boosts/cuts the mid-frequency range.
Boosts/cuts the low-frequency range.
1 – 8
Sets the output level of the module.
PARAMETER 1
DEPTH
DEPTH
POSITION
DEPTH
POSITION
FLT TYPE
SHIFT
POSITION
FREQ
SIZE
TIME
TIME
Range
0 – 10
Adjusts the depth of the effect.
1 – 30
Adjusts the speed of the effect.
0 – 30
Adjusts the mix amount of the effect.
Adjusts the amount of feedback.
AF / bF
Exchanges the effect locations of the DRIVE module and MOD module.
1 – 4
Changes the type of the phase tone.
0 – 10
Emphasizes the effect.
Specifies the center frequency of the wah.
Specifies the frequency.
1 – 8
Sets the output level of the module.
OFF / On
Specifies whether the expression pedal will be used as a wah pedal.
bPF / LPF
Specifies the type of filter.
1 – 10
Adds character to the sound.
-10 – 10
Adjusts the sensitivity with which the effect is applied.
-12.0 – 24.0
Sets the amount of shift produced by the pitch shifter.
0 – 10
Adjust the tone.
0 – 30
Adjusts the balance between the direct sound and effect sound.
0 – 10
Emphasizes the low-frequency range.
1 – 10
Specifies the spatial width.
Sets the delay time.
0 – 30
Adjusts the mix amount of the effect sound.
0 – 30
Adjusts the mix amount of the direct sound.
PARAMETER 2
MID
Explanation of parameter
PARAMETER 1
THRSHOLD
PARAMETER 1
MIN VOL
PARAMETER 2
RATE
RATE
RATE
RATE
FREQ
POSITION
TONE
RATE
DEPTH
TONE
WET LVL
FB
Explanation of parameter
PARAMETER 3
LOW
PARAMETER 3
MIX
FB
COLOR
CLIP
LEVEL
RESO
BALANCE
BALANCE
LowBoost
MIX
DRY LVL
MIX
Appendix
PARAMETER 4
LEVEL
PARAMETER 4
--
--
--
--
RTM
SENS
--
--
--
--
--
--
167
Advertisement
Table of Contents
