Zoom MRS-1266 Operation Manual page 169

Explanation of MODULATION/DELAY MODULE parameters
Parameter name Range
DEPTH
RATE
COLOR
CLIP
-12.0 – 24.0
SHIFT
BALANCE
FREQ
LowBoost
SIZE
TYPE = FLANGER : -10 – 10
FB
TYPE = DELAY : 0 – 10
TYPE = DELAY : 1 – 50
TYPE = DOUBLE : 1 – 100
TIME
1 – 100
TONE
MIX
■ LINE ALGORITHM
COMP/LIM MODULE
TYPE
COMP A stereo input/output compressor.
A stereo input/output limiter.
LIMITER
Explanation of COMP/LIM MODULE parameters
Parameter name Range
SENS
ATTACK
LEVEL
THRSHOLD
RELEASE
ISOLATOR MODULE
TYPE
ISOLATOR
An effect that divides the signal into three frequency bands, and lets you specify the mix amount.
Explanation of ISOLATOR MODULE parameters
Parameter name Range
XOVER_Lo 50 – 16000
XOVER_Hi 50 – 16000
MIX_HIGH OFF, -24 – 6
MIX_MID OFF, -24 – 6
MIX_LOW OFF, -24 – 6
EQ MODULE
TYPE
3BandEQ
Three-band equalizer.
*For an explanation of the parameters, refer to the GUITAR/BASS algorithm.
ZNR MODULE
TYPE
ZNR
Zoom's proprietary noise reduction that minimizes noise when you are not playing.
*For an explanation of the parameters, refer to the DUAL algorithm.
VOL PDL MODULE
TYPE
VOL PDL
You can use an expression pedal to control the volume.
*For an explanation of the parameters, refer to the DUAL algorithm.
ZOOM MRS-1266
0 – 10
Specifies the depth of the effect.
1 – 30
Specifies the speed of the effect.
1 – 4
Modifies the type of phase tone.
0 – 10 Emphasizes the effect.
Specifies the amount of pitch shift produced by the pitch shifter.
0 – 30
Adjusts the balance between the direct sound and effect sound.
1 – 5
Specifies the frequency.
Emphasizes the low range.
0 – 10
1 – 10 Specifies the spatial width.
Adjusts the amount of feedback.
Sets the delay time. ( x 10 mSec )
Sets the delay time. ( x 1 mSec )
Sets the delay time. ( x 1 mSec )
0 – 10
Adjusts the tone.
0 – 30
Adjusts the mix amount of the effect.
PARAMETER 1
SENS
THRSHOLD
0 – 15
Specifies the input sensitivity of compression.
0 – 15 Adjusts the speed at which compression is applied.
1 – 8 Specifies the output level of the module.
0 – 15 Specifies the sensitivity at which the limiter will begin to apply.
0 – 15 Specifies the time from when the input signal falls below the threshold until compression ends.
PARAMETER 1 PARAMETER 2
XOVER_Lo XOVER_Hi
Specifies the frequency at which the Lo/Mid bands will be divided.
Specifies the frequency at which the Mid/Hi bands will be divided.
Specifies the mix amount of the high range.
Specifies the mix amount of the mid range.
Specifies the mix amount of the low range.
PARAMETER 1
HIGH
Explanation of parameter
PARAMETER 2
ATTACK
RELEASE
Explanation of parameter
PARAMETER 3
MIX_HIGH
Explanation of parameter
PARAMETER 2
MID
PARAMETER 1
THRSHOLD
PARAMETER 1
MIN VOL
PARAMETER 3
LEVEL
LEVEL
PARAMETER 4
MIX_MID
PARAMETER 3
LOW
Appendix
PARAMETER 5
MIX_LOW
PARAMETER 4
LEVEL
169