Frymaster H55 Series Technical Reference Manual page 120

Error Log Codes
To access the error log, press the home button. Press the service button. Press the manager button. Enter 1656 and
press the check button. Press the E-log button. The ten most recent errors are listed from top to bottom, with the top
error being the most recent error. A "G" indicates a global error such as a filtration error. Side-specific errors in split
vats are indicated by L for left or R for right. Pressing the left down arrow allows scrolling through the errors. If no
errors are present the screen will be blank
Code ERROR MESSAGE
E13 TEMPERATURE PROBE FAILURE
E16 HIGH LIMIT 1 EXCEEDED
E17 HIGH LIMIT 2 EXCEEDED
E18 HIGH LIMIT PROBLEM
DISCONNECT POWER
E19 HEATING FAILURE – XXX F or XXX C
E25 HEATING FAILURE - BLOWER
E27 HEATING FAILURE - PRESSURE SWITCH - CALL SERVICE
E28 HEATING FAILURE – XXX F or XXX C
E29 TOP OFF PROBE FAILURE - CALL SERVICE
E32 DRAIN VALVE NOT OPEN - FILTRATION AND TOP OFF
DISABLED - CALL SERVICE
E33 DRAIN VALVE NOT CLOSED - FILTRATION AND TOP OFF
DISABLED - CALL SERVICE
E34 RETURN VALVE NOT OPEN - FILTRATION AND TOP OFF
DISABLED - CALL SERVICE
E35 RETURN VALVE NOT CLOSED - FILTRATION AND TOP OFF
DISABLED - CALL SERVICE
E36 VALVE INTERFACE BOARD FAILURE - FILTRATION AND
TOP OFF DISABLED - CALL SERVICE
E37 AUTOMATIC INTERMITTENT FILTRATION PROBE FAILURE
- FILTRATION DISABLED - CALL SERVICE
E39 CHANGE FILTER PAD
E41 OIL IN PAN ERROR
E42 CLOGGED DRAIN (Gas)
E43 OIL SENSOR FAILURE - CALL SERVICE
E44 RECOVERY FAULT
E45 RECOVERY FAULT – CALL SERVICE
E46 SYSTEM INTERFACE BOARD 1 MISSING - CALL SERVICE
E51 DUPLICATE BOARD ID - CALL SERVICE
E52 USER INTERFACE CONTROLLER ERROR - CALL SERVICE
E53 CAN BUS ERROR - CALL SERVICE
E55 SYSTEM INTERFACE BOARD 2 MISSING - CALL SERVICE
E62 SLOW HEATING FAILURE XXXF OR XXXC - CHECK ENERGY
SOURCE - CALL SERVICE
E63 RATE OF RISE
E64 FILTRATION INTERFACE BOARD FAILURE - FILTRATION
AND TOP OFF DISABLED - CALL SERVICE
E65 CLEAN OIB SENSOR – XXX F OR XXX C - CALL SERVICE
E66 DRAIN VALVE OPEN – XXXF OR XXXC
E67 SYSTEM INTERFACE BOARD NOT CONFIGURED - CALL
SERVICE
Touchscreen-Equipped Fryers
.
TEMP Probe reading out of range
High limit temperature is past more than 410°F (210°C), or in
CE countries, 395°F (202°C)
High limit switch has opened.
Vat temperature exceeds 460°F (238°C) and the high limit has
failed to open. Immediately disconnect power to the fryer
and call service.
Heating Control latch circuit failed.
Heat Contactor failed to latch.
The air pressure switch(s) failed to close.
The air pressure switch has failed closed.
The fryer has failed to ignite and has locked out the ignition
module.
ATO RTD reading out of range
Drain valve was trying to open and confirmation is missing
Drain valve was trying to close and confirmation is missing
Return valve was trying to open and confirmation is missing
Return valve was trying to close and confirmation is missing
Valve Interface Board connections lost or board failure.
AIF (VIB Probe) RTD reading out of range.
25-hour timer has expired or dirty filter logic has activated.
The system detects that oil may be present in the filter pan.
Vat did not empty during filtration
Oil level sensor may have failed.
Recovery time exceeded maximum time limit.
Recovery time exceeded maximum time limit for two or more
cycles.
-> SERVICE ->3000-> TECH MODE -> RESETS -> RECOVERY
FAULT CALL SERVICE -> YES.
SIB board 1 connection lost or board failure.
Two or more controllers have the same location ID.
The controller has an unknown error.
Communications are lost between boards.
SIB board 2 connection lost or board failure.
The vat is not heating properly.
Rate of rise error occurred during a recovery test.
Filtration Interface Board connections lost or board failure.
Gas -The oil is back sensor does not detect oil. Clean optional
oil sensor.
Drain valve is opened during cooking.
Controller is turned on when the SIB board is not configured.
5-17
EXPLANATION
Reset the error code by going to: HOME -> SERVICE