Henny Penny EVOLUTION ELITE Series Operator's Manual page 74

Press the right arrow button until "ASSIGN BTN" shows in the display, along
6 6 ) )
with the product (ex: NUGGETS). If this product already has a product button
assigned to it, that LED will be lit. To assign other product buttons to that
product, press and hold the product button for 3 seconds and that LED stays lit.
To remove a product from a button, press and hold the product button with a lit
LED and the LED goes out.
C C h h a a n n g g e e T T i i m m e e s s & & T T e e m m p p e e r r a a t t u u r r e e
Press the right arrow button until "COOK TIME" shows in the display, and then
7 7 ) )
use the product buttons, or the up arrow and down arrow buttons, to change the
time in minutes and seconds, to a maximum of 59:59.
Press the right arrow button and "TEMP" shows in the display, along with the
8 8 ) )
preset temperature on the right side of the display. Press the product buttons, or
the up arrow and down arrow buttons, to change the temperature. The
temperature range is 190°F (88°C) to 375°F (191°C).
C C o o o o k k I I D D C C h h a a n n g g e e
Press the right arrow button until "COOK ID" shows in the display along with the
9 9 ) )
product ID. For example, NUG would be the ID for nuggets. Use the product
buttons, or the up arrow and down arrow buttons, to change the ID.
A A l l a a r r m m s s ( ( 1 1 & & 2 2 ) )
Press the right arrow button until "ALRM 1" shows in the left display, and an
1 1 0 0 ) )
alarm time in the right display. Press the product buttons, or the up and down
arrow buttons, to set an alarm. Ex., If a Cook Cycle was set at 3 minutes, and an
alarm was to go off after 30 seconds into the Cook Cycle, "2:30" would be set in
the display at this time. When the timer counts down to 2:30 the alarm sounds.
After alarm time is set, press the right arrow button and "ALRM 2" shows in
display, and a second alarm can be programmed.
Q Q u u a a l l i i t t y y T T i i m m e e r r ( ( H H o o l l d d T T i i m m e e ) )
Press the right arrow button until "QUAL TMR" shows in the display along with
1 1 1 1 ) )
the preset holding time. Press the product buttons or the up and down arrow
buttons to adjust holding time, up to 2 hours: 59 minutes.
A A . . G G l l o o b b a a l l F F i i l l t t e e r r T T r r a a c c k k i i n n g g - - I I n n c c l l u u d d e e I I n n F F i i l l t t e e r r C C o o u u n n t t
1 1 2 2 ) )
Press the right arrow button until "INCL IN FLTR CNT" flashes in display along
with "YES" or "NO". Using the up or down arrow buttons, change the display to
"YES" if that product's Cook Cycles are to be counted as part of the
recommended filter process. Set to "NO" if it is not to be included.
B B . . M M i i x x e e d d F F i i l l t t e e r r T T r r a a c c k k i i n n g g - - F F i i l l t t e e r r A A f f t t e e r r " " X X " " N N u u m m b b e e r r O O f f L L o o a a d d s s
Press the right arrow button until "FILTER AFTER ..." flashes in the left display,
and the number of cook cycles between filters shows in the right display. Press
the product buttons or the up and down arrow buttons to change this value of 0
to 99 loads. This needs set for each product.
64