Selecting Key Fill And Key Source - Sony XVS-9000 User Manual

Multi format switcher system
Hide thumbs Also See for XVS-9000:
Table of Contents

Advertisement

5
Make the following settings as required.
To invert the black and white of the key source:
Press [Key Invert], turning it on.
To adjust the horizontal position or key source
width for a luminance key, linear key, color
vector key, or chroma key: Press [Key Position],
turning it on, and set the following parameters.
No.
Parameter Adjustment
1
H Phase
Key horizontal position
2
Left
Key left edge position
3
Right
Key right edge position
To set the key priority: Press [Key Priority] to open
the M/E-1 >Misc >Key Priority menu (1173), and
set the priority (see page 86).

Selecting Key Fill and Key Source

Selecting the key fill and key source
1
Open the M/E-1 >Key1 >Type menu (1111).
2
In the <Key Fill> group, select the key fill.
Key Bus: Signal selected on the key 1 fill bus
Matte: Signal from a dedicated color matte generator
3
If [Key Bus] is selected in step 2, select a key fill
signal using one of the following methods.
• On the cross-point control block, press delegation
button [KEY1] on the cross-point pad and select a
signal using the cross-point buttons.
• On the cross-point control block in key/AUX bus
delegation mode, press the [KEY1] button in the 1st
row and select a signal using the cross-point buttons
in the 2nd row.
Note
You can assign a key fill bus delegation button to the
1st row or 2nd row of the AUX bus control block
(AUX bus operation mode) in the Setup menu (see
page 410).
4
If [Matte] is selected in step 2, press [Matte Adjust] to
open the Matte Adjust menu (1111.2), and select [Flat
Color] (single color) or [Mix Color] (2-color mix) in
the <Fill Matte> group.
If [Mix Color] is selected, set the color mixing (see
page 111).
If [Flat Color] is selected, adjust color 1 using the
following parameters.
No.
Parameter Adjustment
1
Luminance Luminance
2
Saturation
3
Hue
5
In the <Key Source> group, specify the key source
selection mode.
Self: Selects the key fill bus signal.
Auto Select: Automatically selects the key fill signal
on the cross-point buttons and the signal assigned
with it as a pair.
Split: Allows you to select a separate signal that the
signal that would be selected automatically.
Notes
• When chroma key is selected as the key type, select
[Self].
• When [Split] is selected, the key memory function is
disabled.
6
If [Split] is selected in step 5, select a key source signal
using one of the following methods.
• On the cross-point control block, press and hold
delegation button [KEY1] on the cross-point pad
and select a signal using the cross-point buttons in
the 2nd row.
• Press and hold the [SPLT] button in the key control
block, then select a signal using the cross-point
buttons in the 2nd row in the cross-point control
block.
• On the Flexi Pad control block in key operation
mode, press and hold the [KEY1] button in the
memory recall section and select a signal using the
cross-point buttons in the 2nd row in the cross-point
control block.
• On the cross-point control block in key/AUX bus
delegation mode, press and hold the [KEY1] button
in the 1st row and select a signal using the cross-
point buttons in the 2nd row.
When a cross-point button is pressed, a key signal is
selected.
To select a video signal, first set the [KEY] button
operation mode in the Setup menu (see page 111).
Notes
• On the cross-point control block in key bus mode or
free assign mode, you can select a key fill signal in
the 1st row and a key source signal in the 2nd row by
pressing and holding the following buttons.
- Key bus delegation buttons on the cross-point pad
- [SPLT] button on the key control block
110
Saturation
Hue

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents