Sony XVS-9000 User Manual page 441

Switcher signal Input signal format
format
3840×2160P • 3840×2160P (Level A, 2SI) 3G
(Level A, 2SI)
• 3840×2160P (Level A, 2SI) 12G
• 3840×2160P (Level B, 2SI) 3G
• 3840×2160P (Level A, SQD)
• 3840×2160P (Level B, SQD)
• 1080P (Level A)
• 1080P (Level B)
• 1080i
3840×2160P • 3840×2160P (Level A, 2SI) 3G
(Level A, SQD)
• 3840×2160P (Level A, 2SI) 12G
• 3840×2160P (Level B, 2SI) 3G
• 3840×2160P (Level A, SQD)
• 3840×2160P (Level B, SQD)
• 1080P (Level A)
• 1080P (Level B)
• 1080i
1080P • 1080P (Level A)
(Level A)
• 1080P (Level B)
• 1080i
• 720P
1080i • 1080i
• 720P
• 576i
• 480i
720P • 1080i
• 720P
• 576i
• 480i
a) Input signal without format conversion
b) Not selectable on the XKS-S8111
c) Selectable on the XKS-S8111 when the 720P converter is disabled and on
the XKS-S8112/XKS-S9112
d) Selectable on the XKS-S8111 when the 720P converter is enabled and on
the XKS-S8112/XKS-S9112
e) Selectable on the XKS-S8111 only
f) When the switcher signal format frequency is 59.94, only 480i is
selectable. When the frequency is 50, only 576i is selectable.
1
In the Engineering Setup >Switcher >Input >Input FC/
CCR menu (7332.1), press [FC Format].
The FC Format menu (7332.7) appears.
The status area shows the input list on the left and the
supported conversion signal format list on the right.
2
Select the target input connector board to set.
No. Parameter Adjustment
1 Group No Input group number
a) Inputs on an input connector board form a group.
3
In the list on the left, select the target input to set.
Select an input from among the input grouping to set.
a)
a)
a)
c)
c)
d)
a)
e) f)
e) f)
a)
e) f)
e) f)
a)
Note
When the switcher signal format is 3840×2160P, only
the input with the lowest number in the input grouping
a) b)
can be selected.
4
In the list on the right, select the signal format.
5
Press [Set].
To clear the signal format setting
Press [Clear].
b)
6
Press [Execute].
Setting the format converter conversion
method
You can set the format converter conversion method for
each input.
For details about the conversion method items and the
target conversion formats, see "Setting the format
converter conversion method" (page 437).
1
In the Engineering Setup >Switcher >Input >Input FC/
CCR menu (7332.1), press [FC Adjust].
The FC Adjust menu (7332.8) appears.
2
Display the target input to set in the status area.
Press [Prev] or [Next] to switch the display in the
status area.
Pressing [Prev] displays the previous four inputs, and
pressing [Next] displays the next four inputs.
Pressing [Prev Group] or [Next Group] displays the
four inputs of the input connector board installed in the
previous slot or next slot, respectively.
3
In the status area, select an input.
4
Set the conversion method.
The operation is similar to setting an internal format
converter.
For details, see "Setting the format converter
conversion method" (page 437).
Setting the frame delay
To set the frame delay level
You can set the frame delay level for each input.
1
In the Engineering Setup >Switcher >Input >Input FC/
CCR menu (7332.1), select the target input to set.
2
Set the following parameter.
441