Sony XVS-9000 User Manual page 444

When 3840×2160P 2SI 3G or 3840×2160P SQD signals
are output, 3G×4 output signals are assigned as a single
group to a 4K signal. The output setting is specified for
the first number output in each group of four outputs in
the same way as for the XVS-8000/7000/6000.
• XVS-8000/7000/6000 output setting: Four outputs are
assigned as a single group to a 4K signal.
A single group comprises four outputs in numeric order
starting from the first output, and settings are applied to
the first number in each group.
Output connector number Setting number
1, 2, 3, 4
5, 6, 7, 8
9, 10, 11, 12
13, 14, 15, 16
(and so on)
When XKS-S8167 12G-SDI Output Board output
connectors are set to 12G mode, 3840×2160P 2SI
signals are output as a 12G×1 signal, but the output
setting is available only for the first number output in
each group of four outputs.
M/E dedicated outputs
On the XVS-8000, M/E dedicated output connectors 1 to
16 can be used by installing an XKS-S8165 SDI Output
Connector Board in slot 2.
Two outputs (Ext Out1, Ext Out2) configured on each
switcher bank can be assigned to M/E dedicated outputs as
output signals. The switcher bank Out1 to Out4 signals can
be configured as an Ext Out output signal.
For details about M/E dedicated output settings, see
"Setting M/E Dedicated Outputs" (page 447).
Notes
• M/E dedicated outputs are not supported on the
XVS-9000/7000/6000.
• M/E dedicated outputs are enabled only when the
switcher signal format is 3840×2160P. Four M/E
dedicated outputs can be used.
• The following functions are not available on an M/E
dedicated output.
Video clips, vertical blanking, through mode, safe titles,
4:3 crop
Multi viewer output connectors settings
On the XVS-9000, multi viewer output connectors can
function as output connectors 81 to 96.
You can assign output signals to output connectors 81 to
96 in the same way as other output connectors. To use the
connectors as multi viewer output connectors, multi
viewer outputs must be assigned to output connectors 81 to
96.
For details, see "Assigning Output Signals" (page 445).
1
5
9
13
(and so on)
444
Output signal format conversion
The following format converters can be used.
Internal format converter: Configurable when an XKS-
8460 Format Converter Board is installed (see
page 448).
Output format converter: Configurable when an XKS-
S9167 12G-SDI Output Board is installed (see
page 450).
P/I converter: Converts a 1080P format signal to 1080i
for output (see page 451).
Notes
• On the XVS-9000, internal format converters and P/I
converters are not available.
• On the XVS-8000/7000/6000, output format converters
are not available.
Format converter outputs
You can enable the internal format converter function if an
XKS-8460 Format Converter Board is installed. Format
converter outputs 1 to 16 correspond to format converter
channels (FC1 to FC16).
You can assign format converter outputs for output to
format converter output connectors 1 to 16 or spare
connectors 1 to 4 on an output connector board.
On the XVS-8000, the number of format converter output
connectors will vary depending on the number of output
connector boards installed. Spare connectors 1 to 4 can be
used if an output connector board for the multi viewer is
installed.
On the XVS-7000, output connectors 1 to 16 of the output
connector boards installed for format converters are used.
Spare connectors 1 to 4 can be used if an output connector
board for the multi viewer is installed.
On the XVS-6000, output connectors 1 to 16 of the output
connector boards installed for format converters are used.
Spare connectors cannot be used.
For details about format converter output connectors and
spare connectors, see "XVS-9000/8000/7000/6000 Multi
Format Switcher" (page 62).
Notes
• When using a network connector board (XKS-T8165/
XKS-Q8166), signals cannot be converted to other than
the following signal formats by the format converter.
- NMI: 3840×2160P 2SI, 1080P, 1080i
- ST2110: 1080i
• In 4K format, only FC1, FC5, FC9, and FC13 can be
configured.
• The following functions are not supported on format
converter outputs.
Video clips, vertical blanking, through mode, safe titles,
4:3 crop, AUX bus color corrector, AUX mix transitions