Sony XVS-9000 User Manual page 66

h OUTPUT 49 to 52 connectors (BNC type: XKS-
S8165/XKS-S8167, RJ-45 type: XKS-T8165,
QSFP+ type: XKS-Q8166)
If an XKS-S8165 is installed in the XVS-8000, these can
be used as output connectors to connect to dedicated
inputs.
i FC (format converter) OUTPUT 1 to 16 connectors
(BNC type: XKS-S8165/XKS-S8167, RJ-45 type:
XKS-T8165, QSFP+ type: XKS-Q8166)
Outputs signals generated using the internal format
converter function. Up to 16 output systems are supported.
The output setting is controlled from the control panel of
the XVS system.
j SPARE 1 to 4 connectors (BNC type: XKS-S8165/
XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type:
XKS-Q8166)
On the XVS-8000, the same signals on the FC OUTPUT 1,
5, 9, and 13 connectors are output, from left to right, on the
SPARE 1, 2, 3, and 4 connectors.
On the XVS-7000, the same signals on the FC OUTPUT 1
and 5 connectors are output on the SPARE 1 and 2
connectors. Signals are not assigned to the SPARE 3 and 4
connectors.
k MV (multi viewer) OUTPUT 1 to 8 connectors
(BNC type: XKS-S8165/XKS-S8167, RJ-45 type:
XKS-T8165, QSFP+ type: XKS-Q8166)
Multiple output signals can be combined and output as
serial digital video signals arranged in a grid. Up to two
output systems are supported.
The output setting is controlled from the control panel of
the XVS system.
l SPARE 5 to 8 connectors (BNC type: XKS-S8165/
XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type:
XKS-Q8166)
Reserved for future use.
m OUTPUT 25 to 32 connectors (BNC type: XKS-
S8165/XKS-S8167, RJ-45 type: XKS-T8165,
QSFP+ type: XKS-Q8166)
Used as multi viewer output 1 to 8 connectors on the
XVS-6000.
Multiple output signals can be combined and output as
serial digital video signals arranged in a grid. Up to two
output systems are supported.
The output setting is controlled from the control panel of
the XVS system.
n -AC IN (AC power input) connectors (3-pin)
XVS-9000: A, B, C, D, E, and F connectors
XVS-8000/7000: A, B, C, and D connectors
XVS-6000: A and B connectors
Connect to 100 V to 240 V AC power supply with AC
power cords (sold separately).
o U (signal ground) terminal
Connect to the system ground.
p MVS LAN (multi format video switcher LAN)
connector (RJ-45 compliant)
Connect to an Ethernet switch.
Used to communicate between switcher control stations
connected to an Ethernet switch.
1) For details about supported Ethernet switches, contact your Sony service
or sales representative.
For details about Ethernet switch connection, refer to the XVS-9000/8000/
7000/6000 Installation Manual.
q UTL LAN (utility LAN) connector (RJ-45
compliant)
Reserved for future use.
Do not connect any signal to this connector.
r GPI connector (D-sub 25-pin)
Outputs an alarm when a switcher error occurs.
s RESET CIRCUIT BREAKER buttons
If an overcurrent condition is detected, due to a short
circuit or other cause, the button will pop out,
disconnecting the circuit. The button pops out approximate
5
3.5 mm ( / inches).
32
t REF IN (reference video signal input) connectors
(BNC type)
Connect to an HD tri-level sync signal, black burst signal,
or analog sync signal when using the unit synchronized to
an external sync signal.
The two connectors are loop-through, so that the signal
input on either connector is also output on the other
connector. Connect the supplied 75 Ω terminator to the
remaining connector if not using the loop-through output.
About 4K signal input/output connector
assignment
In 4K format, a subdivided-by-4 image (sub images) are
transferred as four separate signals, where the 4K signal is
assigned to four input/output connectors.
On connector boards that support 12G-SDI,
can be transferred using a single cable.
1) 12G-SDI is an interface for digital transfer of 4K signals using a co-axial
cable that supports 12 Gbps transfer speeds.
When assigning to four connectors
On the following connector boards, a 4K signal is assigned
to a group of four connectors.
• Input connector boards: XKS-S8110/XKS-S8111/
XKS-T8110/XKS-Q8111
• Output connector boards: XKS-S8165/XKS-T8165/
XKS-Q8166
66
1)
1)
a 4K signal