Extron electronics System 8 Plus User Manual page 53

im Vertrieb von
Command and Response
Command/Response Table
Command Response String
String Hex Switcher to Host
↵Cx↵ (x is the channel #, 1 - 154)
x! * 21
↵Ax↵ (x is the audio channel #, 1 - 154)
x$ * 24
↵Vx↵ (x is the video channel #, 1 - 154)
x& * 26
↵Cx↵ (x is the channel #, 1 - 154
x@ * 40
* a channel number of up to 3 digits
↵Blk·1↵
B 42
↵Blk·Ø↵
b 62
c 63 (Same command as C below)
↵CONFIGURED·FOR·AMPRO··(POWER·UP····↵
C 43
This is an example response and may vary depending on the internal setting for the projector type.
(Same command as I below)
i 69
↵Vx
I 49
V - Video (x
A - Audio (x
T - Video Type. (x
P - Display Power status. (x
S - Display Mute status. (x
Z - Switcher Mute (x
R - Switcher RGB Mute status. (x
QSC - Switcher Comm software version # (3 digits x
QPC - Projector Comm software version # (3 digits x
M - Maximum channel available (x
An example of a response to the I/i command: ↵V3·A3·T2·P0·S0·Z1·R1·QSC1.10·QPC1.09·M8↵
n 6E (Same command as N below)
↵N60-107-01↵
N 4E
o 6F (Same command as O below)
↵PR·1↵
O 4F
↵PW·1↵
↵PW·E↵
↵PR·Ø↵
q 71 (Same command as Q below)
↵QSCx.xx↵
Q 51
↵QPCy.yy↵
r 72 (Same command as R below)
↵BLK·1↵
R 52
↵BLK·Ø↵
s 73 (Same command as S below)
↵MUT·1↵
S 53
↵MUT·Ø↵
x 78 (Same command as X below)
↵UNLOCKED·FRONT·PANEL↵
X 58
↵LOCKED·OUT·FRONT·PANEL↵
z 7A (Same command as Z below)
↵AMUT·1↵
Z 5A
↵AMUT·Ø↵
↵PR·1↵
[ 5B
↵PW·1↵
↵PW·E↵
↵PR·0↵
] 5D
↵MUT·1↵
( 28
↵MUT·Ø↵
) 29
↵AMUT·1↵
+ 2B
↵AMUT·Ø↵
- 2D
Error Response Codes
↵EØ1↵
↵EØ2↵
↵EØ3↵
↵EØ4↵
www.camboard.de
Extron • System 8/10 P
LUS
CAMBOARD Electronics
·Ax ·Tx ·Px ·Sx ·Zx ·Rx ·QSCx
1 2 3 4 5 6 7
= channel # 1 to 154; if Ø = Sys power is off)
1
= channel # 1 to 154; if Ø = Sys power is off)
2
= 1 if RGBS, 2 if RGsB, 3 if Composite video, 4 if S-Video)
3
4
= Ø mute is off; 1 = on.)
5
= Ø, mute is off; 1 = on.)
6
(this is just an example response and may vary)
As an example: ↵QSC1.10↵
As an example: ↵QPC1.09↵
Tel. 07131 911201
• User's Manual
Fax 07131 911203
Command
Description; etc.
Select Channel (See page A-2)
Character following Command channel
number is a delimiter. It defines end of
Command string and further defines
the Select Channel command.
Turn Switcher RGB Mute ON
Turn Switcher RGB Mute OFF
Request Projector Configuration
Information Request
.x x ·QPCx .x x ·Mx
8 9 10 11 12 13
= Ø power is off; 1 = on.)
= Ø, mute is off; 1 = on.)
7
.x x
8 9
.x
11
= 8 - 154)
14
Request Part Number
Toggle Display Power
Display power is ON, was off
Please wait, Initializing
Please wait, End
Display power is OFF, was on
Query (See QSC & QPC above.)
x.xx = Switcher Comm software version
y.yy = Projector Comm software version
Toggle Switcher RGB Mute
Switcher RGB Mute ON, was off
Switcher RGB Mute OFF, was on
Toggle Display Mute
Display Mute is ON, was OFF
Display Mute is OFF, was ON
Toggle Executive Mode
If currently in Executive Mode
If not in Executive Mode
Toggle Switcher Audio Mute
Switcher Audio Mute is ON, was off
Switcher Audio Mute is OFF, was on
Turn Display Power ON
Please wait, initializing
Please wait, END
Turn Display Power OFF
Turn display mute ON
Turn display mute OFF
Turn Switcher Audio Mute ON
Turn Switcher Audio Mute OFF
Invalid Channel Number
Slave Communication Error
Projector is Powered OFF
Projector Communication Error
ce-info@camboard.de
RS-232 Programming Guide
↵
14
)
10
x )
12 13
A-4