Roland SP-606 Owner's Manual page 40

Chapter 2. Using Effects
*1: For effect types 43–45, you can hold down [FUNC] and press [F2] (SUB) to access a sub-parameter screen. The tables shown
below list the parameters that appear in these screens. Press [F3] (EXIT) to return to the previous screen.
43 SUBSONIC Value
E.LEVEL 0–127
PITCH 0–127
ATTACK 0–127
44 OSCILLATOR(PAD)
EFFECT LEVEL
PAD1 KEY
LFO RATE
LFO WAVE
OSC TUNE
OSC VIB DEPTH
OSC XMOD
OSC LEVEL
SUB OSC WAVE
SUB OSC TUNE
SUB OSC VIB DEPT
SUB OSC LEVEL
RING SRC1
RING SRC2
RING LEVEL
NOISE LEVEL
PORTA TIME
45 ENVELOPER(PAD)
ATTACK
FILTER TYPE
*2: Available note values for synchronization (In the case of delay time, the result cannot exceed approximately three seconds.)
32nd note( ), 16th note(
8th note( ), quarter note(
note( )
40
Explanation
Adjusts the volume of the effect sound.
Adjusts the frequency of the sine wave.
Adjusts the time from when the source exceeds the threshold until the sine wave is heard.
Value Explanation
0–127 Adjusts the volume of the effect sound.
C- –G9 Adjusts the key sounded by the oscillator when you press PAD 1.
0–127 An LFO is an oscillator used to apply modulation; by increasing the vibrato or PWM you
can modulate the pitch or tone in a variety of ways.
SAW,
TRI
TRI, (Triangle wave)
SQR,
SQR
(Square wave)
S-H
SAW
(Sawtooth wave)
S-H
(Sample & Hold wave)
-24–+24 Specifies the coarse tuning (semitone steps) of the oscillator pitch.
0–127 Adjusts the depth of vibrato (using the LFO to cyclically modulate the pitch) for the oscil-
lator.
0–127 Adjusts the depth of cross modulation (using the SUB OSC to modulate the pitch of the
oscillator).
0–127 Adjusts the volume of OSC.
SAW, Selects the SUB OSC waveform. (The choices are the same as for OSC WAVE on p. 39)
TRI,
PLS1–9
-24–+24 Adjusts the coarse tuning (semitone steps) of the SUB OSC pitch.
0–127 Adjusts the depth of vibrato (using the LFO to cyclically modulate the pitch) for the SUB
OSC.
0–127 Adjusts the SUB OSC volume.
OSC, Selects the two inputs for the ring modulator.
SUB (MFX IN: MFX input source)
OSC,
NOISE,
MFX IN
0–127 Adjusts the volume of the ring modulator.
0–127 Adjusts the volume of the noise generator.
0–100 Adjusts the time over which pitch change will occur for the portamento effect (which cre-
ates smooth transitions between pitches).
Value Explanation
0–127 Adjusts the time from when you release the pad until the volume falls to the minimum.
LP (-12), Low pass filter with a -12 dB slope
BP (-12), Band pass filter with a -12 dB slope
HP (-12), High pass filter with a -12 dB slope
LP (-24), Low pass filter with a -24 dB slope
BP (-24), Band pass filter with a -24 dB slope
HP (-24) High pass filter with a -24dB slope
), 8th note triplet( ), dotted 16th note(
), half note triplet( ), dotted quarter note(
), 8th note( ), quarter note triplet(
), half note( ), dotted half note(
), dotted
), whole