Icom ID-31A PLUS Advanced Manual page 183

11
MENU SCREEN
Function items
VOX
MENU > Function > VOX > VOX
Turn the VOX function ON or OFF�
The Voice Operated Transmission (VOX) function
starts transmission without pushing [PTT] when you
speak into the microphone, and then, automatically
returns to receive when you stop speaking�
• OFF: Turns OFF the function�
• ON: Starts transmission without pushing [PTT]
when you speak into the microphone� Then
automatically returns to receive when you
stop speaking�
VOX Level
MENU > Function > VOX > VOX Level
Set the VOX gain level to between 1 and 10, or OFF�
Higher values make the VOX function more sensitive
to your voice� To turn the VOX function OFF, set to
"OFF�"
• OFF: Turns the VOX function OFF�
• 1 ~ 10: 1 (The minimum sensitivity)
10 (The maximum sensitivity)
VOX Delay
MENU > Function > VOX > VOX Delay
Set the VOX Delay to 0�5, 1�0, 1�5, 2�0, 2�5, or 3�0
seconds� The VOX Delay is the amount of time the
transmitter stays ON after you stop speaking before
the VOX switches to receive�
VOX Time-Out Timer
MENU > Function > VOX > VOX Time-Out Timer
Set the VOX Time-Out Timer to prevent an accidental
prolonged transmission� To disable the function, set to
"OFF�"
• OFF:
• 1, 2, 3, 4, 5, 10, or 15min: If a continuous
Headset Select
MENU > Function > VOX > Headset Select
Select the headset type to be connected�
• HS-95: Select when using the HS-95�
• Other: Select when using the HS-94 or HS-97�
(Default: OFF)
(Default: 5)
(Default: 0.5sec)
(Default: 3min)
Turns the function OFF�
transmission exceeds the
set period of time, the
transmission is cut off�
(Default: Other)
CI-V (DATA Jack)
MENU > Function > CI-V > CI-V (DATA Jack)
Selects whether or not to use the [DATA] jack to
remotely control the transceiver�
L When you use the optional RS-MS1A, set to
"ON (Echo Back OFF)�"
• OFF:
• ON (Echo Back OFF): Use the [DATA] jack
• ON (Echo Back ON): Use the [DATA] jack
CI-V Address
MENU > Function > CI-V > CI-V Address
To distinguish devices, each CI-V transceiver has its
own Icom standard address in hexadecimal code�
The ID-31A/ID-31E PLUS's default address is A0�
When 2 or more ID-31A/ID-31E PLUSs are
simultaneously controlled by a PC, set a different
address for each transceiver between 02h and DFh
(hexadecimal)�
CI-V Baud Rate
MENU > Function > CI-V > CI-V Baud Rate
Set the CI-V data transfer speed to 300, 1200, 4800,
9600, 19200 bps, or Auto� When "Auto" is selected,
the baud rate is automatically set according to the
data rate of the controller�
L You can select "300," "1200," or "Auto" only when CI-V
(DATA Jack) is set to "OFF�"
CI-V Transceive
MENU > Function > CI-V > CI-V Transceive
Turn the CI-V Transceive function ON or OFF�
L When you use the optional RS-MS1A, set to "ON�"
• OFF: Turns OFF the function�
• ON: When you change a setting on one
transceiver, the same settings is
automatically changed on the other
connected transceivers or receivers�
11-40
(Default: OFF)
Does not use the [DATA]
jack to remotely control the
transceiver�
to remotely control the
transceiver�
L Does not send back the CI-V
command input from the
[DATA] jack�
to remotely control the
transceiver�
L Sends back the CI-V
command input from the
[DATA] jack�
(Default: A0)
(Default: Auto)
(Default: OFF)