Siemens SIMATIC S7-200 System Manual page 600

Index
Single-phase wiring guidelines, 2-13
Size of the modules
CPU 221, 2-4
CPU 222, 2-4
CPU 224, 2-4
CPU 226, 2-5
expansion I/O modules, 2-5
screw sizes for installation, 2-4–2-5
SM0.2 retentive data lost memory bit, 5-18
SMB0 status bits, C-1
SMB1 status bits, C-2
SMB166 – SMB194: PTO, PT1 Profile
Definition Table, C-16
SMB186–SMB194 receive message control,
C-12
SMB2 freeport receive character, C-2
character interrupt control, 9-192
SMB200 – SM299: Intelligent module status,
C-16
SMB28, SMB29 analog adjustment, 6-13, C-6
SMB3 freeport parity error, C-2
character interrupt control, 9-192
SMB30 – SMB165: HSC Register, C-14
SMB30, SMB130 freeport control registers,
9-188, C-6
SMB34/SMB35 time-interval registers, C-8
SMB36–SMB65 HSC register, C-9
SMB4 queue overflow, C-3
SMB5 I/O status, C-3
SMB6 CPU ID register, C-4
SMB66–SMB85 PTO/PWM registers, C-11
SMB7 reserved, C-4
SMB8–SMB21 I/O module ID and error
registers, C-5
SMB86–SMB94 receive message control,
C-12
SMB98 and SMB99, C-14
SMW22–SMW26 scan times, C-6
Index-20
Special memory bits, C-1–C-13
addressing, 5-5
SMB0 status bits, C-1
SMB1 status bits, C-2
SMB166 – 194: PTO, PT1 Profile Definition
Table, C-16
SMB186–SMB194 receive message
control, C-12
SMB2 freeport receive character, C-2
SMB200 – 299: Intelligent module status,
C-16
SMB28, SMB29 analog adjustment, C-6
SMB3 freeport parity error, C-2
SMB30 – 165: HSC Register, C-14
SMB30, SMB130 freeport control registers,
9-188, C-6
SMB31 permanent memory (EEPROM)
write control, C-7
SMB34/SMB35 time interval registers, C-8
SMB36–SMB65 HSC register, C-9
SMB4 queue overflow, C-3
SMB5 I/O status, C-3
SMB6 CPU ID register, C-4
SMB66–SMB85 PTO/PWM registers, C-11
SMB7 reserved, C-4
SMB8–SMB21 I/O module ID and error
registers, C-5
SMB86–SMB94 receive message control,
C-12
SMB98 and SMB99, C-14
SMW222–SMW26 scan times, C-6
SMW32 permanent memory (EEPROM)
write control, C-7
Specifications
creating functional, 4-3
Input simulator, A-93
S7-200 family, A-3
Square Root instruction, 9-85, 10-21
Standard contact instructions, 9-2, 10-2
Standard rail
clearance requirements, 2-2–2-4
dimensions, 2-3
high-vibration installations, 2-7
installation procedure, 2-7
removal procedure, 2-8
using DIN rail stops, 2-7
vertical installations, 2-7
Standards, national and international, A-2
Statement List, program status, 4-35
Statement list, 4-6
Statement List Editor, 4-6
Status bits (SMB0), C-1
S7-200 Programmable Controller System Manual
A5E00066097-02