Siemens SIMATIC S7-200 System Manual page 588

Index
Errors
compile rule violations, B-4
fatal, B-2
Network Read/Network Write, 9-180
non-fatal, B-3, B-4
PID loop, 9-97
run-time programming, B-3
SMB1, execution errors, C-2
USS Protocol instructions, 11-16
European Community (EC) certification, A-2
Examples
Add to Table, 9-108
analog adjustment, 6-13
And, Or, Exclusive Or, 9-117–9-119,
10-26–10-28
ASCII to HEX, 9-139
block move, 9-104–9-106
calculating power requirements, 2-18
call to subroutine, 9-153–9-155
comparison contact instructions, 9-14
contact instructions, 9-5, 10-4
Convert and Truncate, 9-134, 10-33
counter, 9-25, 10-17
Decode/Encode, 9-136
decrement, 9-81, 10-20
First-In-First-Out, 9-111
For/Next, 9-156–9-158
High-Speed Counter, 9-47
operation of HSC0 Mode 0 and HSC1 or
HSC2 Modes 0, 1, or 2, 9-29
operation of HSC1 or HSC2 Modes 3, 4,
or 5, 9-30
operation of HSC1 or HSC2, Modes 6, 7
or 8, 9-30
operation of HSC1 or HSC2, Modes 9,
10, or 11, 9-31
operation with Reset and Start, 9-29
operation with Reset and without Start,
9-28
I/O numbering, 6-2, 6-3
increment, 9-81, 10-20
Interrupt Routine instructions, 9-178
Invert, 9-119–9-121
Jump to Label, 9-148–9-150
Last-In-First-Out, 9-112
logic stack, 9-200–9-202
loop control (PID), 9-98–9-100
math, 9-78, 9-84, 10-19
memory fill, 9-113–9-115
move and swap, 9-105–9-107, 10-24–10-26
MPI card with master/slave, 7-4
Network Read/Network Write, 9-182–9-184
Index-8
on-delay timer, 9-20, 9-21, 10-13, 10-14
output instructions, 9-9, 10-6
Pulse Train Output, 9-65, 9-68
Pulse width modulation, 9-63
Real number conversion instruction, 9-134,
10-33
retentive on-delay timer, 9-22
Segment, 9-138
Sequence Control Relay, 9-159–9-164
conditional transitions, 9-166
convergence control, 9-163–9-166
divergence control, 9-161
set up timed interrupt, 4-18
shift and rotate, 9-126–9-128, 10-29–10-31
shift register bit, 9-129–9-131
Stop, End, and Watchdog Reset,
9-147–9-149
Table Find, 9-110
TD 200s added to network, 7-12
transmit instructions, 9-193
Truncate, 9-134, 10-33
USS Protocol program, 11-20
Exclusive Or Byte instruction, 9-114
Exclusive Or Double Word instruction, 9-116
Exclusive Or instruction, 10-25
Exclusive Or Word instruction, 9-115
Execution times, STL instructions, F-1
Expansion cable, specifications and
installation, A-89
Expansion modules, 1-5, 1-6
addressing I/O points, 6-2
dimensions
8- and 16-point I/O modules, 2-5
screw sizes for installation, 2-4–2-5
ID and error register (SMB8 to SMB21),
C-5
installation procedure
panel, 2-6
rail, 2-7
order numbers, E-1
power requirements, 2-18
removal procedure, 2-8
screw sizes for installation, 2-4–2-5
terminal block connector, 2-12
S7-200 Programmable Controller System Manual
A5E00066097-02