Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. PMW-EX3...
Page 3
Hävitä käytetty paristo valmistajan ohjeiden Remplacer uniquement avec une batterie du même mukaisesti. type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. 1 (P) PMW-EX3...
Related manuals The following manuals are available in this model. If this manual is required, please contact your local Sony Sales Office/Service Center..Operating Instructions (Supplied with the unit) This manual is necessary for application and operation (and installation) of this unit.
MIC/LINE (H) +4 dBu, selectable MIC/LINE (C) High impedance, Balanced 8 S-VIDEO OUT : S-video connector (4P) _ _ _ _ _ EXT VIEW _ _ _ _ _ No. Signal Specifications Y/C_GND Y/C_GND S OUT (Y) S OUT (C) PMW-EX3...
Page 10
CHASSIS GND CHASSIS GND TPB_ Strobe on receive, data on transmit B (_) TPB+ Strobe on receive, data on transmit B (+) TPA_ Data on receive, strobe on transmit A (_) TPA+ Data on receive, strobe on transmit A (+) PMW-EX3...
Page 11
GND: ON OPEN: OFF SW COMMON FRAME GND !; Battery : (5P) _ _ _ _ _ EXT VIEW _ _ _ _ _ No. Signal Specifications BATT (+) +11 to +17 V dc BAT_SCL BAT_SDA BATT_ID_DATA BATT (_) PMW-EX3...
IC (IC100). In the . S-Video (analog): To JK-84 board camera signal processor IC (IC100), average value, peak value of the RGB digital video signals that are required for . LCD signal (digital): To IF-1072 board PMW-EX3...
PCI- ing, as well as microphone +48 V power supply and serial Express signals. signal. IC1302 is controlled by PCI bus from IC900. (RTC is also built on this board, but the explanation has been omitted here.) PMW-EX3...
Page 16
IC314 of the camera block system, IC400 of the JK-84 board (Audio block) video signal system, and IC900 of the media recording/ This is the connector board. The audio output from the playback system. ASW-66 board is connected to RCA PIN connector. PMW-EX3...
Page 17
IC400 and by IC521 to control the VCXO IC1001 on the RE-261 board checks that the power switch (X500). on the PMW-EX3 is turned ON, and turns on the system controller of IC1600. After that, it controls the power for (3) TC IN/TC OUT each circuit block according to the system controller.
Page 18
This helps provide detailed information about detection, automatic recovery is not performed and the the battery, including whether the battery is damaged or power must be turned on again. how long the life is, in order to provide optimal operations. 1-10 PMW-EX3...
For preventing screw from being loosened !- 7-651-000-10 Sony (SGL-601) 50 g grease Lubricant * : This cable is supplied with PMW-EX3. 1, 3 1-4-2. Measuring Equipment Use the calibrated equipment or equivalent as listed below for the adjustments. Equipment...
7. Attach the pad sub assembly and pad center cover. When the PMW-EX3 is connected to the computer for the first time, the driver software will need to be installed into the computer. For more details, check the readme file that comes with the upgrade software.
1-6. Recommended Replacement Parts This section describes the recommended replacement parts and recommended replacement time. Part name Sony part No. Recommended replacement timing Lens hood 4-110-064-01 Check for deformation and deterioration from time to time. Replace it as necessary. Eye cup...
. The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-14 PMW-EX3...
KSW-54 board (A side) KSW-54 board (B side) Board The PMW-EX3 uses flexible card wires and coaxial cables with connector. The following diagrams indicate the location of each connector. The location of flexible card cables are indicated by the circle number 1 and 2, while the coaxial cables with connector are not indicated by the circle number.
Connector (Fine Pitch Coaxial Cable) The flat cables, flexible card wires and boards are used to The PMW-EX3 uses coaxial cables with connector. connect between the following boards. Life of flexible card wire will be significantly shortened if it is folded. Be very...
Page 25
When connecting the coaxial cable with connector, hold the connector matching the polarity marks and insert the coaxial cable straight into the corresponding connector. Polarity marks Yellow Terminal side Hold the connector to connect. Not to bend the cable. 1-17 PMW-EX3...
Abnormality in obtaining the lens switch Check the connection with the lens unit. If there is no condition defect, replace the lens unit. 17017 Internal error in the media block Repair the DPR-289A board or replace it. 4XXXX 1-18 PMW-EX3...
(tripod). Bottom panel 3. Remove the four screws (M2 x 4), and remove bottom panel. M2 x 4 (Black) M2 x 6 (Black) 4. Reinstall the removed parts by reversing the Bracket (tripod) steps of removal. PMW-EX3...
B. Pad stopper 4. Remove the four screws, and remove the pad M2 x 4 cover. (Black) Pad cover 5. Reinstall the removed parts by reversing the steps of removal. PMW-EX3...
. Check to see that the contacting surface is free from stain and dust. Insert the cable by holding Do not bend the connector. the cable. . Hold the connector with its contacting surface facing upward, and check that the polarity marks are aligned. PMW-EX3...
4. Remove the five screws (M2 x 4). While Spring M2 x 6 disengaging the two claws, remove the (Black) handle top cover assembly. Accessory Handle top shoe cover assembly 5. Reinstall the removed parts by reversing the steps of removal. PMW-EX3...
M2 x 4 (Silver) board. Control switch block 9. Disconnect the HN-328 board from the connector (CN1) on side-B of the KSW-54 M2 x 4 (Silver) board. Harness HN-328 board 10. Reinstall the removed parts by reversing the steps of removal. PMW-EX3...
10. Reinstall the removed parts by reversing steps 1 to 5. Check that the switch (S1) on the IF-1069 board engages with the knob. IF-1069 board Knob PMW-EX3...
7. Reinstall the removed parts by reversing the steps of removal. When installing the screws that were re- moved in step 5, tighten them with the specified tightening torque. Tapping P2.6 x 6 tightening torque: ± 0.15 N.m (8.0 ± 1.5 kgf.cm) 80 x 10 PMW-EX3...
B2.6 x 6 (Silver) DPR-289A board by the coaxial cable with connector. When disconnecting the coaxial cable with connector, be very careful not to apply HN-343 board physical load to the coaxial cable with CN800 connector. DPR-289A board connector PMW-EX3...
Page 36
HP-144 board, and route the harness between the rear shoe bracket and the HP jack. Then route the harness along the Rear shoe bracket underside of the HP jack. HP jack 14. Refer to Section 2-2-5 and reinstall the “Handle Top Cover Assembly”. 2-10 PMW-EX3...
Harness Arrange the extra length of the harness coming from the VF slide arm in the direc- tion shown by the arrow. Confirm that the harness does not run on top of the area shown in the illustration. 2-11 PMW-EX3...
Page 38
50 x 10 Turn the lock lever fully counterclockwise VF assembly and confirm that the VF assembly can move smoothly in the directions of A and B as shown by the arrow. 11. Reinstall each part by reversing step 1. 2-12 PMW-EX3...
Page 39
: P2 tapping 2 x 5 : P2 tapping 2 x 5 9. Reinstall the removed parts by reversing the steps of removal. When reinstalling the removed tapping screw again, refer to note of section “2-2. Replace- ment Procedures.” 2-13 PMW-EX3...
Top panel earth bracket Key top assembly (top panel) SWC-49 board Top panel cover 5. Reinstall the removed parts by reversing the steps of removal. When reinstalling the removed tapping screw again, refer to note of section “2-2. Replace- ment Procedures.” 2-14 PMW-EX3...
7. Disconnect the connector (CN2) of the HN- 337 board from the connector (CN101) of the ASW-66 board, and remove the inside panel HN-337 board assembly. ASW-66 board CN101 Inside panel assembly Reinstall the removed parts by reversing the steps of removal. 2-15 PMW-EX3...
(CN1) on the CN-3050 board, arrange the harness so that it is routed inside the notch of the frame and inside the hatched portion. . When reinstalling the removed tapping screw again, refer to note of section “2-2. Replacement Procedures.” 2-16 PMW-EX3...
. Check that the four knobs of the AU slide switch are normally engaged with the four corresponding switches (S100 through S103) on the ASW-66 board. . When reinstalling the removed tapping screw again, refer to note of section “2-2. Replacement Procedures.” 2-18 PMW-EX3...
. Check that the knob of the power switch is normally engaged with the switch (S301) on the SW-1410 board. . When reinstalling the removed tapping screw again, refer to note of section “2-2. Replacement Procedures.” 2-19 PMW-EX3...
SWC-48 board SWC-48 board CN100 CN holder HN-344 board CN101 Claws 6. Reinstall the removed parts by reversing the steps of removal. When reinstalling the removed tapping screw again, refer to note of section “2-2. Replace- ment Procedures.” 2-20 PMW-EX3...
Tape (LED) b and the three screws (M2 x 4) of c, and M2 x 4 (Silver) remove the SWC-48 board. Tapping 2 x 5 (Black) M2 x 4 (Silver) CN600 SWC-48 board Inside panel assembly Screws c 2-21 PMW-EX3...
Page 48
. Do not re-use the tape on which adhesive agent is coated. . When reinstalling the removed tapping screw again, refer to note of section “2-2. Replacement Procedures.” Hole of SWC-48 board Fold SWC-48 board 2-22 PMW-EX3...
(to be abbreviated as “O-assembly” hereafter), stand the unit and the O-assembly vertically. Then, move the O-assembly toward the unit in parallel with the unit, and install the O-assembly. Do not install the O-assembly at an angle. 2-23 PMW-EX3...
(Silver) HN-345 board SHUTTER ON/OFF knob Front panel assembly S502 6. Reinstall the removed parts by reversing the steps of removal. Check that the SHUTTER ON/OFF knob is normally engaged with the switch (S502) on the SW-1389 board. 2-24 PMW-EX3...
(20 x 30) to the location shown by the end surface. illustration. 20 mm Align the end surface. Do not re-use the tape on which adhesive agent is coated. Tape (20 x 30) 9. Reinstall each part by reversing step 1. Power supply harness 2-25 PMW-EX3...
5. Disconnect the harnesses from the connector RE-260 board (CN1) on the RE-260 board. 6. Disconnect the coaxial cable from the coaxial connector on the TX-129 board. Pull out from notch Coaxial cable EC-63 boards TX-129 board CN-3023 board Harness clamp (BTOB) 2-26 PMW-EX3...
Page 53
Coaxial cable Install the coaxial cable with connector in the with connectors way that the yellow wire faces to the bottom. EC-63 board Yellow wire Bottom side 12. Reinstall each part by reversing steps 1 to 3. 2-27 PMW-EX3...
EMC bracket Hooks engaging the hook portion of the EMC (EXDD bottom) M2 x 4 bracket (EXDD bottom) with the EX-DD (Silver) bracket, and fix it with two screws. 9. Reinstall each part by reversing step 1. EX-DD bracket 2-28 PMW-EX3...
CN-3022 board 4. Remove the RE-260 board from the EX-DD bracket in the direction of arrow C. M2 x 4 (Silver) CN200 CN-3022 board RE-260 board EX-DD bracket 5. Reinstall the removed parts by reversing the steps of removal. 2-29 PMW-EX3...
M2 x 4 (Silver) M2 x 4 (Silver) Heat sink (EX) rear Radiation sheet (EC) rear Radiation sheet M2 x 4 Heat sink (Silver) (EX) front EC-63 board EX bracket 8. Reinstall the removed parts by reversing the steps of removal. 2-30 PMW-EX3...
6. Remove the PS-747 board from the capacitor case. Capacitor case Outside connector assembly 7. Reinstall the removed parts by reversing the steps of removal. When installing the outside connector assembly, tighten finally the three screws securing the outside connector assembly at this step. 2-31 PMW-EX3...
7. Remove the four screws (BTP2.6 x 6), M2 x 4 (Silver) disengage protrusion of the pad rail and the two dowels from groove of the main frame, and remove the pad rail in the direction of arrow B. Cushion (BP) Harness 2-32 PMW-EX3...
Page 59
11. Remove the four screws, and remove the heat M2 x 4 sink. (Silver) 12. Remove the DPR-TX bracket assembly and the radiation sheet (TX) from the TX-129 board. Heat sink Radiation sheet (TX) TX-129 board DPR-TX bracket assembly 2-33 PMW-EX3...
Page 60
16. Reinstall each part by reversing steps 5 to 6. 17. Attach the ferrite core to the pad rail with the tape 50. Ferrite core Pad rail Tape 50 18. Reinstall each part by reversing steps 1 to 3. 2-34 PMW-EX3...
Connector HN-347 board Harness (DC146-RE260) 6. Reinstall the removed parts by reversing the steps of removal. When installing the outside connector assembly, tighten the three screws tentatively. Tighten them finally when installing the PS-747 board in section 2-2-28. 2-35 PMW-EX3...
. Check to see that the contacting surface is Contacting free from stain and dust. surface . Hold the connector with its contacting surface facing upward, and check that the Insert the cable by holding Do not bend the connector. polarity marks are aligned. the cable. 2-36 PMW-EX3...
28 to 2-2-32, and disassemble the unit up to “Lens Mount Block” removal. 2. Remove the four screws, and remove the prism block unit. Prism block unit Lens mount block 3. Reinstall the removed parts by reversing the steps of removal. 2-37 PMW-EX3...
Lens mount block IR-42 board CN102 Filter sheet Dowels 4. Reinstall the removed parts by reversing the steps of removal. When installing the SE-923 board, place the filter sheet underneath the SE-923 board, and install the SE-923 board. 2-38 PMW-EX3...
Groove of front frames Be careful not to drop the inside PC board guide. AU-318 board Groove of front frames Inside PC board guide Lens mount block 6. Reinstall the removed parts by reversing the steps of removal. 2-39 PMW-EX3...
7. Apply a dose of thread locking adhesive agent of about one third of the size of a rice grain in between the frame and the four screws that were fixed in step 6. 8. Reinstall each part by reversing steps 1 to 4. 2-40 PMW-EX3...
Page 67
T/W zoom switch, assemble it by Protrusion rotating it in the direction opposite to the (START/STOP) Notch arrow. (Fig. 2) 3. Install the three screws a, and the screw b. Fig.5 (Fig. 1) Grip cover Buckle Grip belt Fig.6 2-41 PMW-EX3...
4. Pass the HN-343 board through a ferrite core, and connect it to the connector on the SWC- 48 board. M2 x 4 (Silver) Tape (LED) SWC-48 board 5. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-13.) 2-42 PMW-EX3...
Gasket (rear center) 2. Attach the gasket (rear center) at the position shown in the illustration. Gasket (rear center) Align center. Push against rib. 3. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-21.) 2-43 PMW-EX3...
(Refer to Section 2-2-21.) 2. Attach the gasket (main top) at the position shown in the illustration. Gasket (main top) Should not protrude. Projection Gasket (main top) 3. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-21.) 2-44 PMW-EX3...
EMC sheet that was Coaxial cable with connectors attached in step 2 is covered by the tape. Bundle Spread Valley fold Binding tape 1 to 3 mm Tape (13 x 50) Align the ends. Align the ends. EMC sheet 2-45 PMW-EX3...
Page 72
5. Attach the gasket (VF) at the position shown in the illustration. Gasket (VF) Push against rib. Push against the side surface. 6. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-10 and 2-2-9.) 2-46 PMW-EX3...
DPR-289A board. DPR-289A board EMC sheet Wrap the tape. Align the 7 to 10 mm end surface. Wrap the tape. Tape (13 x 50) 6. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-21.) 2-47 PMW-EX3...
5. Connect the connector on which the EMC sheet is attached, to the HN-337 board. Harness (HN337-CN3050) Spread Bundle Valley fold 1 to 3 mm EMC sheet Tape (13 x 50) 6. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-24.) 2-48 PMW-EX3...
(20 x 30) to the location shown by the illustration. Tape (20 x 30) Align the end surface. 20 mm Align the end surface. 3. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-13.) 2-49 PMW-EX3...
(Refer to Section 2-2-21.) 2. Attach the gasket (rear center) at the position shown in the illustration. Gasket (rear center) Align center. Push against rib. 3. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-21.) 2-50 PMW-EX3...
(Refer to Section 2-2-21.) 2. Attach the gasket (main top) at the position shown in the illustration. Gasket (main top) Should not protrude. Projection Gasket (main top) 3. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-21.) 2-51 PMW-EX3...
DPR-289A board. DPR-289A board EMC sheet Wrap the tape. Align the 7 to 10 mm end surface. Wrap the tape. Tape (13 x 50) 6. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-21.) 2-52 PMW-EX3...
(20 x 30) to the location shown by the illustration. Tape (20 x 30) Align the end surface. 20 mm Align the end surface. 3. Assemble the removed parts by reversing steps of removal. (Refer to Section 2-2-13.) 2-53 PMW-EX3...
Compensation register or delete the manual registration. Channel Selects and displays the channel (R-ch or G-ch or B-ch) to execute manual registration or detection of RPN correction on. Cursor Turns On or Off the RPN correction point indicator cursor. PMW-EX3...
Exiting the Menu Mode device and setting parameters that must be set uniquely to Press the MENU button again. each PMW-EX3 for correction of non-uniformity between The system exits the menu mode to return to the normal the respective lens characteristics.
Page 84
. The Auto BLK Shad menu enables the auto black shading correction (automatic optimization of the respective correction values of the black shading correc- tion). . When Auto BLK Shad menu is selected, the Execute and Cancel choices appear. Selecting Execute starts Auto Black Shading. PMW-EX3...
Page 85
. The V Saw menu enables the vertical Saw black shading correction (linear increase and decrease) level. . The V Para menu enables the vertical Parabola white shading correction (sensitivity correction at the vertical center with respect to both ends) level. PMW-EX3...
Page 86
R Flare, G Flare and B Flare to ± 0. . Adjust lens iris until white level becomes approximately 100%. After that, open the lens iris by two stops. . Select waveform of the signal at the center of grayscale signal on a waveform monitor. PMW-EX3...
Cursor V Position, . When the Cursor menu is turned On, the crosshair cursor the RPN cursor moves in the descending order of the indicating the RPN correction position is displayed Cursor H Position.) superimposed on the video signal. PMW-EX3...
. The RPN data that is registered at the factory and the RPN data is manually registered cannot be deleted by the Reset. . When the Reset menu is selected, the Execute and Cancel choices appear. In addition, selecting Execute starts reset of RPN. PMW-EX3...
Page 89
IC to AVIT signal processing IC Item13 4bit I/F while playing back between Diagnosis of the 4bit Bus signal line (playback direction) from display and media block AVIT signal processing IC to base band processing IC PMW-EX3...
Page 90
Shows the number of trials of the self-diagnosis. Success Shows the number of internal successes of the self-diagnosis. Result Shows the result of the self-diagnosis. “0” means no problems. When a value other than “0” is displayed, check the details for each self-diagnostic item. 3-10 PMW-EX3...
Page 91
Display block diagnosis analyzes the following contents. Diagnosis description Error value Type 1/2 Note 0x01 Communication signal line -1: Connection error 1, 2 test of LCD 0x02 Communication signal line -1: Connection error 1, 2 test of COPRO (SAD) 3-11 PMW-EX3...
Page 92
Audio block diagnosis analyzes the following contents. Diagnosis description Error value Type 1/2 Note 0x02 Memory area check for -1: Memory read/write 1, 2 audio block comparison NG When an error is detected in the item, it indicates a possible error in the hardware. 3-12 PMW-EX3...
Page 93
When an error is detected in the IIC communication test, it indicates a possible failure in the communication line or device. *: When an error is detected in the version matching test, upgrade again to a compatible version. Contact your local Sony Sales Office/Service Center for information on versions. Item6: Power block diagnosis Power block diagnosis analyzes the following contents.
Page 94
Executing Log Dump acquires the error log information and saves it to the active, writable media. Select Log Dump under the INFORMATION menu, and execute it with Execute. The process is complete when “Log Dump Done” is displayed as a result. Do not remove the media until this message appears. 3-14 PMW-EX3...
Section 4 Alignment 4-1. Servicing software “ServiceNavi-EX” Servicing software “ServiceNavi-EX” is required for electrical adjustment and self diagnosis. For how to obtain the “ServiceNavi-EX”, contact your local Sony Sales Office/Service Center. PMW-EX3...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. 3. Stock of Parts Parts marked with “o”...
Page 99
3-452-468-01 s BELT, GRIP 3-875-399-01 s LID, REAR 3-875-400-01 s CAP 4-142-737-01 s CAP, MOUNT 4-143-402-01 s LEVER 4-143-410-01 s CAP, LENS 3-364-941-11 s SCREW (+B) (2.6X5), NYLOK 4-644-493-01 s ACE (M2.6), LOCK 7-685-792-09 s SCREW +PTT 2.6X6 (S) PMW-EX3...
Page 100
Pad Block BTP2.6 x 8 BTP2.6 x 8 BTP2.6 x 8 PMW-EX3...
Page 101
3-878-248-01 s SPRING PAD 3-364-941-11 s SCREW (+B) (2.6X5), NYLOK 3-654-058-12 s SPACER (3X2) 3-080-203-31 s SREW(M2),LOCK ACE,P2 3-701-444-21 s WASHER 6 3-878-278-01 s SIDEPAD L 3-878-281-05 s BOTTOM COVER, SIDEPAD L 7-685-534-19 s SCREW +BTP 2.6X8 TYPE2 N-S PMW-EX3...
Page 102
Handle Block 2 To KSW-54 board (CN1) VF FRONT To KSW-54 board (CN300) To KSW-54 To IF-1069 board (CN7) board (CN5) To KSW-54 board (CN2) To LED-469 To IF-1069 board (CN2) board (CN4) PMW-EX3...
Page 103
3-878-269-02 s LOCK,SCREW 4-641-726-13 s SCREW (M2), SPECIAL HEAD 1-887-248-11 s PRINTED WIRING BOARD, HN-348 3-694-181-03 s TYPE1, AROCK PRECISION +P2.6X5 4-644-493-01 s ACE (M2.6), LOCK 4-119-886-01 s TAPE (13X50) 4-121-111-01 s SHEET, EMC 4-115-173-01 s GASKET (MAIN TOP) PMW-EX3...
Page 104
VF Front and VF Rear +P2.6 x 4 +P2.6 x 4 PIN2 To KSW-54 board (CN300) +P2.6 x 4 To Main Frame 2 DPR-289A board +P2.6 x 4 PMW-EX3...
Page 105
3-878-271-02 s ARM 3-878-272-01 s GUIDE 3-878-269-02 s LOCK, SCREW 4-109-147-01 s LABEL, CAUTION 4-641-726-13 s SCREW (M2), SPECIAL HEAD 3-701-505-01 s SET SCREW, DOUBLE POINT 3X3 4-108-765-01 s TAPE 25 7-621-284-00 s SCREW +P 2.6X4 7-626-314-31 s SPRING PIN 2X16 PMW-EX3...
Page 106
Outside Panel and Battery To IF-1069 board (CN4) To LED-469 board (CN2) To HN-328 board (CN2) In Side Panel 5-10 PMW-EX3...
Page 107
3-876-773-01 s LID, BUTTON BATTERY 3-876-774-01 s CASE BATTERY 3-876-777-01 s LEVER EJECT 3-876-778-01 s COVER, LEVER EJECT 3-876-781-01 s SW EJECT 3-877-746-02 s COVER, CONNECTOR (1) 3-877-980-01 s COVER, CONNECTOR (2) 3-878-253-02 s PANEL, BOTTOM 3-878-538-01 s PANEL (1), OUT SIDE 5-11 PMW-EX3...
Page 108
Inside Panel 1 To LED-469 board (CN2) STOP RING 1.2 STOP RING 1.5 5-12 PMW-EX3...
Page 109
3-878-515-01 s SPRING , COMPRESSION COIL 3-878-516-01 s SHAFT (1) 3-878-517-02 s SHAFT (3) 3-878-530-01 s SPRING (LID), PLATE 3-878-627-01 s SPRING, LID 3-878-700-01 s CUSHION INSIDE 7-624-101-04 s STOP RING 1.2 (E TYPE) 7-624-102-04 s STOP RING 1.5, TYPE -E 5-13 PMW-EX3...
Page 110
Inside Panel 2 To HN-328 board (CN2) To SW-1410 board (CN300) To AU-318 board (CN4) 5-14 PMW-EX3...
Page 111
3-080-206-21 s SCREW, TAPPING, P2 3-877-677-01 s KEY TOP (ASSIGN) 3-877-689-01 s KEY TOP (FRAME) 3-877-759-01 s HOLDER, CN 3-878-018-01 s BRACKET (FRAME/FULL AUTO) 3-878-080-01 s SPACER, LIGHT INTERCEPTION 3-878-532-01 s PANEL(1) , IN SIDE 3-878-890-02 s TAPE (SWC48) 5-15 PMW-EX3...
3-080-206-21 s SCREW, TAPPING, P2 3-286-759-01 s CUSHION CN3007 3-694-181-03 s TYPE1,AROCK PRECISION +P 2.6X5 3-876-722-01 s BRACKET, EX 3-878-258-02 s BRACKET, EX-DD 3-878-890-02 s TAPE (SWC48) 3-878-657-01 s TAPE50 4-644-493-01 s ACE(M2.6), LOCK 4-115-173-01 s GASKET (MAIN TOP) 5-17 PMW-EX3...
Main Frame 1 To SDI Out To CN-3024 board (CN6) BTP2.6 x 6 BTP2.6 x 6 To ASW-66 board (CN101) To CN-3050 board (CN1) 5-18 PMW-EX3...
Page 115
1-966-168-11 s HARNESS, SUB (TX121-CN3024) 3-056-233-21 s SCREW (M2), LOCK ACE, P2 3-878-254-02 s RAIL, PAD TOP 3-878-656-01 s TAPE 60 3-878-657-01 s TAPE 50 3-878-255-01 s RAIL,PAD BOTTOM 1-500-944-11 s CORE, FERRITE 7-685-533-19 s SCREW +BTP 2.6X6 TYPE2 N-S 5-19 PMW-EX3...
Page 116
To EC-63 Harness (DPR-LCD) board (CN1) To EC-63 board (CN1) To RE-260 board (CN1) To TX-129 To PS-747 board (CN700) board (CN1) From prism block unit P3 x 8 To TX-129 board (CN800) From HN-326 baord P3 x 8 5-20 PMW-EX3...
3-876-718-02 s BRACKET, CN (OUT) 3-876-719-01 s S BRACKET 3-876-727-02 s BRACKET (OUT) REAR, CONNECTOR 3-876-885-01 s CLAMP, CN OUTSIDE 4-644-493-01 s ACE(M2.6), LOCK 4-121-111-01 s SHEET, EMC 4-119-886-01 s TAPE (13X50) 7-685-146-11 s SCREW +P 3X8 TYPE2 NON-SLIT 5-21 PMW-EX3...
Lens Mount To BP-42 board (CN1) To DPR-289A To DPR-289A board board To DPR-289A To DPR-289A board board PRECISION PRECISION K1.7 K1.7 5-22 PMW-EX3...
Page 119
3-876-883-01 s CUSHION (FRONT) 3-878-241-01 s HOLDER, LENS MOUNT 4-644-493-01 s ACE(M2.6), LOCK 1-788-851-11 s LENS MOUNT 1-877-242-11 s PRINTED WIRING BOARD, HN-346 1-877-241-11 s PRINTED WIRING BOARD, HN-345 3-878-657-01 s TAPE50 7-627-450-98 s SCREW, PRECISION +K 1.7X5 TYPE1 5-23 PMW-EX3...
1-208-863-81 s RES, CHIP 100 (1005) IC104 6-713-118-01 s IC PCA9554BS-T R153 1-208-863-81 s RES, CHIP 100 (1005) R156 1-208-911-81 s RES, CHIP 10K (1005) IC105 6-707-862-01 s IC TC74VHC05FT(EKJ) R157 1-208-927-81 s RES, CHIP 47K (1005) IC106 6-807-802-01 s IC UPD78F0533AGB(S)-402-UEU-A 5-24 PMW-EX3...
Page 121
C136 1-124-779-21 s CAP, ELECT 10MF (4.3X5.5) C137 1-124-779-21 s CAP, ELECT 10MF (4.3X5.5) C138 1-124-779-21 s CAP, ELECT 10MF (4.3X5.5) C203 1-164-935-81 s CAP, CHIP CERAMIC 470PF B 1005 C204 1-126-401-21 s CAP, CHIP ELECT 1MF (4X5.7) 5-25 PMW-EX3...
Page 122
D205 8-719-820-42 s DIODE 1SS302-TE85L 1-218-903-91 s RES, CHIP 220K (1608) D206 8-719-820-42 s DIODE 1SS302-TE85L 1-218-863-91 s RES, CHIP 4.7K (1608) 1-218-849-91 s RES, CHIP 1.2K (1608) 6-703-223-01 s IC MAX668EUB+TG069 1-211-969-91 s RES, CHIP 10 (1608) 5-26 PMW-EX3...
Page 123
1-208-891-81 s RES, CHIP 1.5K (1005) R239 1-208-935-81 s RES, CHIP 100K (1005) R144 1-218-990-81 s CONDUCTOR, CHIP (1005) R240 1-208-891-81 s RES, CHIP 1.5K (1005) R145 1-218-990-81 s CONDUCTOR, CHIP (1005) R241 1-208-927-81 s RES, CHIP 47K (1005) 5-27 PMW-EX3...
Page 124
1-208-863-81 s RES, CHIP 100 (1005) R406 1-208-863-81 s RES, CHIP 100 (1005) R409 1-208-927-81 s RES, CHIP 47K (1005) RB401 1-233-578-21 s RES, CHIP NETWORK 47K (3216) RB402 1-233-578-21 s RES, CHIP NETWORK 47K (3216) 1-781-696-31 s VIBRATOR, CRYSTAL (32.768 KHz) 5-28 PMW-EX3...
Page 125
1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-208-923-81 s RES, CHIP 33K (1005) 5-29 PMW-EX3...
Page 126
1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 5-30 PMW-EX3...
Page 127
1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-208-923-81 s RES, CHIP 33K (1005) 5-31 PMW-EX3...
1-218-990-81 s CONDUCTOR, CHIP (1005) 1-400-580-21 s FERRITE, EMI (SMD) 1-400-580-21 s FERRITE, EMI (SMD) THP1 1-805-726-11 s THERMISTOR, POSITIVE 1-400-580-21 s FERRITE, EMI (SMD) THP2 1-805-726-11 s THERMISTOR, POSITIVE THP3 1-805-726-11 s THERMISTOR, POSITIVE THP4 1-805-726-11 s THERMISTOR, POSITIVE 5-32 PMW-EX3...
Page 129
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C356 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C357 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C238 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C358 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-33 PMW-EX3...
Page 130
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C566 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C723 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C567 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C724 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-34 PMW-EX3...
Page 131
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C802 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) C966 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C803 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) C967 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-35 PMW-EX3...
Page 132
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1106 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1333 1-165-646-91 s CAP, CERAMIC 3.3MF B (2012) C1107 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1334 1-112-197-91 s CAP, CERAMIC 10PF CH (0603) 5-36 PMW-EX3...
Page 133
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1546 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1615 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1547 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1616 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-37 PMW-EX3...
Page 134
FB900 1-400-580-21 s FERRITE, EMI (SMD) FB901 1-400-580-21 s FERRITE, EMI (SMD) FB110 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB902 1-400-580-21 s FERRITE, EMI (SMD) FB111 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB903 1-400-580-21 s FERRITE, EMI (SMD) 5-38 PMW-EX3...
Page 135
IC510 8-759-561-46 s IC AD8014ARTZ-REEL7 L1501 1-414-400-41 s INDUCTOR (SMD) 22.0UH IC511 8-759-561-46 s IC AD8014ARTZ-REEL7 L1502 1-414-400-41 s INDUCTOR (SMD) 22.0UH IC512 8-759-561-46 s IC AD8014ARTZ-REEL7 IC513 8-759-561-46 s IC AD8014ARTZ-REEL7 L1503 1-414-400-41 s INDUCTOR (SMD) 22.0UH 5-39 PMW-EX3...
Page 136
1-240-676-91 s RES, CHIP 22 (0603) R357 1-240-683-91 s RES, CHIP 100 (0603) R108 1-240-676-91 s RES, CHIP 22 (0603) R358 1-240-695-91 s RES, CHIP 1K (0603) R109 1-240-676-91 s RES, CHIP 22 (0603) R360 1-240-676-91 s RES, CHIP 22 (0603) 5-40 PMW-EX3...
Page 137
1-240-676-91 s RES, CHIP 22 (0603) R508 1-246-191-91 s RES, CHIP 220K (0603) R437 1-240-676-91 s RES, CHIP 22 (0603) R509 1-240-800-91 s RES, CHIP 4.7K (0603) R438 1-240-676-91 s RES, CHIP 22 (0603) R510 1-245-581-91 s RES, CHIP 1M (0603) 5-41 PMW-EX3...
Page 138
1-240-830-91 s RES, CHIP 100K (0603) R809 1-240-679-91 s RES, CHIP 47 (0603) R600 1-240-707-91 s RES, CHIP 10K (0603) R810 1-240-703-91 s RES, CHIP 4.7K (0603) R601 1-240-714-91 s RES, CHIP 47K (0603) R811 1-240-714-91 s RES, CHIP 47K (0603) 5-42 PMW-EX3...
Page 139
1-240-676-91 s RES, CHIP 22 (0603) R1228 1-240-706-91 s RES, CHIP 8.2K (0603) R1022 1-240-676-91 s RES, CHIP 22 (0603) R1229 1-240-706-91 s RES, CHIP 8.2K (0603) R1023 1-240-676-91 s RES, CHIP 22 (0603) R1230 1-240-706-91 s RES, CHIP 8.2K (0603) 5-43 PMW-EX3...
Page 140
1-240-695-91 s RES, CHIP 1K (0603) R1546 1-240-722-91 s RES, CHIP 220K (0603) R1335 1-240-695-91 s RES, CHIP 1K (0603) R1547 1-240-711-91 s RES, CHIP 22K (0603) R1340 1-240-683-91 s RES, CHIP 100 (0603) R1549 1-240-707-91 s RES, CHIP 10K (0603) 5-44 PMW-EX3...
Page 141
1-240-676-91 s RES, CHIP 22 (0603) R1811 1-240-707-91 s RES, CHIP 10K (0603) R1812 1-240-676-91 s RES, CHIP 22 (0603) R1813 1-240-714-91 s RES, CHIP 47K (0603) R1814 1-240-714-91 s RES, CHIP 47K (0603) R1815 1-240-676-91 s RES, CHIP 22 (0603) 5-45 PMW-EX3...
Page 142
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C356 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C357 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C238 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C358 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-46 PMW-EX3...
Page 143
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C566 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C724 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C567 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C725 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-47 PMW-EX3...
Page 144
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C803 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) C967 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C804 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) C968 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) 5-48 PMW-EX3...
Page 145
1-165-646-91 s CAP, CERAMIC 3.3MF B (2012) C1107 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1334 1-112-197-91 s CAP, CERAMIC 10PF CH (0603) C1108 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1335 1-112-197-91 s CAP, CERAMIC 10PF CH (0603) 5-49 PMW-EX3...
Page 146
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1547 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1614 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1548 1-100-881-91 s CAP, CERAMIC 47MF C (3216) C1615 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-50 PMW-EX3...
Page 147
1-400-462-21 s FERRITE, EMI (SMD) (1005) FB710 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB100 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB711 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB101 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB712 1-400-462-21 s FERRITE, EMI (SMD) (1005) 5-51 PMW-EX3...
Page 148
6-700-599-01 s IC TC7SA08FU(TE85R) L601 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) IC307 6-706-481-01 s IC TC7SET32FU(T5RSOJF) L602 1-414-392-41 s INDUCTOR (SMD) 1.0UH IC308 6-706-481-01 s IC TC7SET32FU(T5RSOJF) L603 1-400-489-11 s COIL, CHOKE 10UH L604 1-456-622-21 s COIL, CHOKE 1UH 5-52 PMW-EX3...
Page 149
1-240-816-91 s RES, CHIP 22K (0603) Q1510 8-729-929-27 s TRANSISTOR DTC114TE-TL R342 1-240-718-91 s RES, CHIP 100K (0603) Q1511 8-729-929-27 s TRANSISTOR DTC114TE-TL R343 1-240-830-91 s RES, CHIP 100K (0603) Q1512 6-550-239-01 s TRANSISTOR DTA144EMFS6T2L R344 1-240-830-91 s RES, CHIP 100K (0603) 5-53 PMW-EX3...
Page 150
1-240-676-91 s RES, CHIP 22 (0603) R483 1-240-676-91 s RES, CHIP 22 (0603) R424 1-240-676-91 s RES, CHIP 22 (0603) R484 1-240-676-91 s RES, CHIP 22 (0603) R426 1-240-676-91 s RES, CHIP 22 (0603) R485 1-240-676-91 s RES, CHIP 22 (0603) 5-54 PMW-EX3...
Page 151
1-240-789-91 s RES, CHIP 1.6K (0603) R702 1-240-672-91 s RES, CHIP 10 (0603) R580 1-240-789-91 s RES, CHIP 1.6K (0603) R703 1-240-778-91 s RES, CHIP 560 (0603) R581 1-240-789-91 s RES, CHIP 1.6K (0603) R704 1-240-794-91 s RES, CHIP 2.7K (0603) 5-55 PMW-EX3...
Page 152
1-240-707-91 s RES, CHIP 10K (0603) R1210 1-240-706-91 s RES, CHIP 8.2K (0603) R1006 1-240-808-91 s RES, CHIP 10K (0603) R1211 1-240-706-91 s RES, CHIP 8.2K (0603) R1007 1-240-676-91 s RES, CHIP 22 (0603) R1214 1-240-706-91 s RES, CHIP 8.2K (0603) 5-56 PMW-EX3...
Page 153
1-240-748-91 s RES, CHIP 33 (0603) R1528 1-240-705-91 s RES, CHIP 6.8K (0603) R1304 1-240-748-91 s RES, CHIP 33 (0603) R1529 1-240-705-91 s RES, CHIP 6.8K (0603) R1305 1-240-748-91 s RES, CHIP 33 (0603) R1530 1-240-705-91 s RES, CHIP 6.8K (0603) 5-57 PMW-EX3...
Page 154
1-240-714-91 s RES, CHIP 47K (0603) RB906 1-234-380-21 s RES, NETWORK 47K (1005X4) R1756 1-240-714-91 s RES, CHIP 47K (0603) RB907 1-234-380-21 s RES, NETWORK 47K (1005X4) R1757 1-240-714-91 s RES, CHIP 47K (0603) RB1000 1-234-370-21 s RES, NETWORK 22 (1005X4) 5-58 PMW-EX3...
Page 155
Ref. No. or Q’ty Part No. SP Description A-1545-708-A s MOUNTED CIRCUIT BOARD, HN-328 ------------ HN-337 BOARD ------------ Ref. No. or Q’ty Part No. SP Description A-1545-797-A s MOUNTED CIRCUIT BOARD, HN-337 1-566-761-11 o PIN, CONNECTOR (PC BOARD) 6P 5-59 PMW-EX3...
1-208-895-81 s RES, CHIP 2.2K (1005) 1-877-248-11 s PWB, HN-348 FLEXIBLE 1-208-895-81 s RES, CHIP 2.2K (1005) 1-216-864-91 s CONDUCTOR, CHIP (1608) 1-771-487-21 s SWITCH, SLIDE ------------ HN-349 BOARD ------------ Ref. No. or Q’ty Part No. SP Description 1-877-244-11 s PWB, HN-349 FLEXIBLE 5-60 PMW-EX3...
Page 157
R103 1-216-864-91 s CONDUCTOR, CHIP (1608) R104 *2 1-208-887-81 s RES, CHIP 1.0K (1005) R105 *2 1-208-887-81 s RES, CHIP 1.0K (1005) R106 *2 1-208-887-81 s RES, CHIP 1.0K (1005) R107 *2 1-208-887-81 s RES, CHIP 1.0K (1005) 5-61 PMW-EX3...
Page 158
1-208-895-81 s RES, CHIP 2.2K (1005) R110 1-208-895-81 s RES, CHIP 2.2K (1005) R111 1-208-895-81 s RES, CHIP 2.2K (1005) R112 1-208-895-81 s RES, CHIP 2.2K (1005) R113 1-208-895-81 s RES, CHIP 2.2K (1005) R114 1-208-895-81 s RES, CHIP 2.2K (1005) 5-62 PMW-EX3...
Page 159
1-208-947-81 s RES, CHIP 330K (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-883-81 s RES, CHIP 680 (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-883-81 s RES, CHIP 680 (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 5-63 PMW-EX3...
Page 160
1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C206 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C207 1-165-989-91 s CAP, CERAMIC 10MF (2012) C208 1-165-989-91 s CAP, CERAMIC 10MF (2012) C209 1-165-989-91 s CAP, CERAMIC 10MF (2012) 5-64 PMW-EX3...
Page 161
6-712-939-01 s IC TPS715A01DRBR 8-719-938-77 s DIODE SB05-05C-TB-E IC308 8-759-588-01 s IC LTC1473CGN-E2 8-719-069-28 s DIODE 1SS400TE-61 IC309 6-706-482-01 s IC TC7SH00FU(T5RSOYJF) 8-719-069-28 s DIODE 1SS400TE-61 IC310 6-706-487-01 s IC TC7SH08FU(T5RSOYJF) 8-719-069-28 s DIODE 1SS400TE-61 IC311 8-759-338-95 s IC NJM2903V(TE2) 5-65 PMW-EX3...
Page 162
8-729-929-27 s TRANSISTOR DTC114TE-TL Q200 8-729-928-28 s TRANSISTOR DTA144EE-TL Q317 8-729-928-28 s TRANSISTOR DTA144EE-TL Q201 8-729-928-28 s TRANSISTOR DTA144EE-TL Q318 8-729-928-82 s TRANSISTOR DTC144EE-TL Q202 8-729-928-28 s TRANSISTOR DTA144EE-TL Q319 8-729-929-27 s TRANSISTOR DTC114TE-TL Q320 8-729-928-28 s TRANSISTOR DTA144EE-TL 5-66 PMW-EX3...
Page 163
1-208-959-81 s RES, CHIP 1M (1005) R224 1-208-959-81 s RES, CHIP 1M (1005) 1-218-990-81 s CONDUCTOR, CHIP (1005) R225 1-208-959-81 s RES, CHIP 1M (1005) 1-208-899-81 s RES, CHIP 3.3K (1005) R227 1-208-911-81 s RES, CHIP 10K (1005) 5-67 PMW-EX3...
Page 164
1-208-927-81 s RES, CHIP 47K (1005) R324 1-208-935-81 s RES, CHIP 100K (1005) R325 1-208-887-81 s RES, CHIP 1.0K (1005) R326 1-208-887-81 s RES, CHIP 1.0K (1005) R327 1-208-887-81 s RES, CHIP 1.0K (1005) R331 1-208-919-81 s RES, CHIP 22K (1005) 5-68 PMW-EX3...
Page 165
6-551-523-01 s TRANSISTOR SI7114DN-T1-E3 8-719-051-04 s DIODE EC10QS04-TE12L5 8-719-069-28 s DIODE 1SS400TE-61 Q113 6-551-523-01 s TRANSISTOR SI7114DN-T1-E3 8-719-069-28 s DIODE 1SS400TE-61 Q114 6-551-523-01 s TRANSISTOR SI7114DN-T1-E3 8-719-069-28 s DIODE 1SS400TE-61 Q115 6-551-523-01 s TRANSISTOR SI7114DN-T1-E3 Q116 8-729-928-28 s TRANSISTOR DTA144EE-TL 5-69 PMW-EX3...
Page 166
1-208-951-81 s RES, CHIP 470K (1005) R114 1-208-927-81 s RES, CHIP 47K (1005) R115 1-208-927-81 s RES, CHIP 47K (1005) R116 1-208-943-81 s RES, CHIP 220K (1005) R117 1-208-943-81 s RES, CHIP 220K (1005) R118 1-208-943-81 s RES, CHIP 220K (1005) 5-70 PMW-EX3...
6-502-153-01 o DI MAZT082HG8S0 R300 1-208-895-81 s RES, CHIP 2.2K (1005) R301 1-208-895-81 s RES, CHIP 2.2K (1005) R302 1-208-895-81 s RES, CHIP 2.2K (1005) R303 1-216-864-91 s CONDUCTOR, CHIP (1608) S300 1-786-157-51 s TACTILE SWITCH S301 1-771-487-21 s SWITCH, SLIDE 5-71 PMW-EX3...
Page 168
1-208-911-81 s RES, CHIP 10K (1005) R605 1-208-927-81 s RES, CHIP 47K (1005) R606 1-208-887-81 s RES, CHIP 1.0K (1005) R607 1-208-911-81 s RES, CHIP 10K (1005) R608 1-208-911-81 s RES, CHIP 10K (1005) R609 1-208-911-81 s RES, CHIP 10K (1005) 5-72 PMW-EX3...
Page 169
1-100-611-91 s CAP, CERAMIC 22MF C (2012) S103 1-786-157-51 s TACTILE SWITCH C504 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 C505 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 C506 1-100-611-91 s CAP, CERAMIC 22MF C (2012) C507 1-100-611-91 s CAP, CERAMIC 22MF C (2012) 5-73 PMW-EX3...
Page 170
C907 1-135-960-91 s CAP, CHIP CERAMIC 10MF B(3225) FB901 *2 1-400-832-21 s SMD EMI FERRITE C908 1-165-989-91 s CAP, CERAMIC 10MF (2012) FB902 *2 1-400-832-21 s SMD EMI FERRITE C909 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 5-74 PMW-EX3...
Page 171
L1008 1-414-398-41 s INDUCTOR (SMD) 10.0UH R348 1-220-878-81 s RES, CHIP 22 (1005) L1009 1-414-396-41 s INDUCTOR (SMD) 4.7UH R349 1-208-935-81 s RES, CHIP 100K (1005) PH800 8-749-014-35 s IC HCPL-0630-500 R401 1-208-911-81 s RES, CHIP 10K (1005) 5-75 PMW-EX3...
R909 1-208-899-81 s RES, CHIP 3.3K (1005) 3-879-020-01 s CLAMP,DC CABLE 3pcs 7-682-560-09 s SCREW +B 4X6 R911 1-208-927-81 s RES, CHIP 47K (1005) R912 1-208-927-81 s RES, CHIP 47K (1005) R913 1-208-891-81 s RES, CHIP 1.5K (1005) 5-76 PMW-EX3...
Page 173
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-06) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.