LG 43LX770M Commercial Mode Setup Manual page 42

Installer Menu (Cont.)
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on "bed
number" in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Note: Item 027 HOSPITAL MODE must be set to 0 to enable
Legacy Zenith Bed 1 or Bed 2 IR codes and Speaker selections.
Values IR Mode
0 – 1 Legacy Zenith (Hospital)
16 – 24 Multi-code Remote
64 – 65 Legacy Zenith (Hospital)
Note: For further information, see Reference section, "Pro:Centric
Patient and Pillow Speaker Remotes." Also, see documentation for
the accessory package that includes the multi-code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to fi lter and control or otherwise restrict program-
ming content that can appear. Set to 0 to turn the V-Chip feature
Off (not available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
Note: This item is not available in the Installer Menu when item 021
V-CHIP is set to 0 or when item 084 PERMANENT BLK is set to 1.
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1
to use the caption setting confi gured before the TV was turned
OFF when the TV is turned ON.
025 - FUNCTION PRE (Function Preview)
Set to 1 to allow access to the Channel Preview/Banks Setup
Menu via the CH PREVIEW key on Installer Remote. Set to 0 to
disable access to the Channel Preview/Banks Setup Menu.
Note: This item is only applicable when the TV is in PTC-CTV
Mode.
027 - HOSPITAL MODE
Set according to the speaker selection, the pillow speaker code/
supply voltage and the hospital IR code. If using a Pro:Centric
pillow speaker, select one of the Zenith codes in accordance with
the desired speaker selection. See table below.
When Hospital Mode is enabled, channel banks are also avail-
able. Refer to "Channel Banks Overview" on page 30 for further
information.
Channel banks are not supported if Hospital Mode is set to 0 or on
TVs that are confi gured for FTG Mode via EBL operation.
42
Bed # Speaker
1 – 2 TV
1 – 9 TV
1 – 2 Pillow
When Hospital Mode is set to 0 (disabled), both the IR code
that will control the TV and the speaker selection depend on the
Installer Menu item 020 FEATURE LEVEL setting.
Note: The default setting (254) is not selectable in the Installer
Menu. If you ever need to restore the default setting, you must set
item 117 FACT DEFAULT to 1 to reload the factory default settings.
See item 117 description for further information.
Note: In the Installer Menu, an informational code is displayed
at the right of each Hospital Mode value. Each code consists of
three characters. The fi rst character—T, P, or B—identifi es the
speaker: TV, Pillow, or Both. The second character—Z, P, R,
or D—identifi es the pillow speaker code: Zenith, Philips, RCA, or
Disabled. The third character—1 or 2—identifi es the bed number.
In the table on the previous page, each bolded character represents
an element of the Hospital Mode code.
028 - CH. OVERIDE (Channel Override)
Applicable for Pass-through Mode only. If set to 1, users can select
channels either with Channel Up/Down or by direct keypad entry.
This setting also allows full access to channel settings in the TV
setup menus (i.e., channels may be added or removed from the
channel lineup, channel labels and icons may be edited, etc.).
If set to 0, the channel lineup is locked. That is, user access to
channel settings in the TV setup menus is restricted, and users can
only tune to the channels that are included in the channel lineup.
Also, in this case, users can only select channels using Channel
Up/Down; direct keypad entry is not available.
Value Speaker
000 Determined by
item 020 setting
001 Pillow Only
002 Pillow Only
017 Pillow Only
018 Pillow Only
033 Pillow Only
034 Pillow Only
065 TV Only
066 TV Only
081 TV Only
082 TV Only
097 TV Only
098 TV Only
129 Both Pillow & TV
130 Both Pillow & TV
145 Both Pillow & TV
146 Both Pillow & TV
161 Both Pillow & TV
162 Both Pillow & TV
254 TV Only
Pillow Speaker
Hospital IR Code
Code/Voltage
Zenith (+12v) Determined by item
020 setting
Zenith (+12v) Zenith Bed #1
Zenith (+12v) Zenith Bed #2
Philips (+5v) Zenith Bed #1
Philips (+5v) Zenith Bed #2
RCA (-5v) Zenith Bed #1
RCA (-5v) Zenith Bed #2
Zenith (+12v) Zenith Bed #1
Zenith (+12v) Zenith Bed #2
Philips (+5v) Zenith Bed #1
Philips (+5v) Zenith Bed #2
RCA (-5v) Zenith Bed #1
RCA (-5v) Zenith Bed #2
Zenith (+12v) Zenith Bed #1
Zenith (+12v) Zenith Bed #2
Philips (+5v) Zenith Bed #1
Philips (+5v) Zenith Bed #2
RCA (-5v) Zenith Bed #1
RCA (-5v) Zenith Bed #2
Disabled (0v) Zenith Bed #2
206-4292 Draft A.2