Behringer DEEPMIND 12 User Manual page 51

51 DeepMind 12 User Manual
RATE - This option is the same as the LFO RATE fader on the surface. Any changes
on the surface will be refl ected here.
The LFO RATE range is from 0 to 255, with 0 being 0.05371 Hz (18.6 s) and 255
being 85 Hz The default LFO RATE setting is 0.
Note: When the ARP-SYNC is ON, the RATE parameter is not shown,
but CLOCK-DIVIDE instead. This shows values based on time division of the
Master BPM RATE as shown below:
Note: For a timing diagram please consult the section later in this document.
RATIO DESCRIPTION
4 Four bars
3 Three bars
2 Two bars
1 One bar
1/2 Half note
3/8 Dotted quarter note
1/3 Third note (Half note triplets)
1/4 Quarter note
3/16 Dotted eighth note
1/6 Sixth note(Quarter note triplets)
1/8 Eighth note
3/32 Dotted sixteenth note
1/12 Twelfth note (Eighth note triplets)
1/16 Sixteenth note
3/64 Dotted thirty-second note
1/24 Twenty-fourth note (Sixteenth note triplets)
1/32 Thirty-second note
3/128 Dotted sixty-fourth note
1/48 Forty-eighth note (Thirty-second note triplets)
1/64 Sixty-fourth note
KEY SYNC - This option allows you to turn KEY-SYNC (Key Synchronisation) On
and Off . When KEY-SYNC is On, the LFO waveform generation will be reset as you
strike a note (keeping in mind the LFO DELAY TIME is also part of the waveform
generation). When KEY-SYNC is Off , the LFO will free run.
LFO KEY SYNC
LFO (KEY SYNC OFF)
KEY GATE
LFO (KEY SYNC ON)
The default KEY-SYNC setting is Off .
ARP SYNC - This option allows you to turn ARP-SYNC (Arpeggiator
Synchronisation) On and Off . When ARP-SYNC is On, the LFO waveform will
synchronize to the Master BPM. When ARP-SYNC is off the LFO will run at the rate
set by the LFO RATE fader/parameter.
LFO ARP SYNC
LFO (ARP SYNC OFF)
ARP CLOCK
LFO (ARP SYNC ON)
The default ARP-SYNC setting is Off .
SLEW-RATE - This option allows you to smooth out the transitions of the LFO
waveform. The SLEW RATE reduces the rate of change of the LFO waveform
shape.
LFO SLEW RATE
0
85
170
255
The SLEW RATE range is from 0-255, with 0 being no change and 255 full
smoothing.
The default SLEW RATE setting is 0.
PHASE - As each voice has independent LFOs, this option allows you to control
the phase relationship between the LFO waveforms.
• • POLY - All voices use an independent LFO. This is the default mode.
• • MONO - All voices use a common LFO.
• • SPREAD - With a setting of 1 there is a 1 degree shift between the LFOs for
each voice. As you begin to increase the SPREAD value the phase of the LFO
for each consecutive voice will be shifted by the amount of SPREAD applied.
I.e. with a 90 degree setting, the fi rst voice will always be at 0 degrees, and
each consecutive voice will be shifted by an additional 90 degrees. So with 4
voice UNISON, voice 1 would be at 0 degrees, voice 2 would be at 90 degrees,
voice 3 would be at 180 degrees and voice 4 would be at 270 degrees.
LFO PHASE SPREAD (UNISON 4 SHOWN)
45
90
180
225
VOICE 1 LFO VOICE 2 LFO
The PHASE range is from 1-254 degrees.
The default PHASE setting is POLY.
To exit the LFO EDIT menu press the EDIT switch again (or press the PROG switch).
to return the main display.
VOICE 3 LFO VOICE 4 LFO