Installing The Bluetooth Terminal; Installing The Gprs Terminal - Ingenico IWL220 Manual

4. Press the GREEN button again and the transaction log for
that acquirer will be printed. It will show the previous 20
transactions for that acquirer. Step 3 and 4 will repeat for
each acquirer.
Once all have been printed, press the GREEN button and the terminal will return to the READY
prompt.
39. How to Assign a Terminal to a Base Unit
Place the terminal handset onto the base unit.
1. At the READY prompt press the MENU button twice.
2. Use the arrow buttons to view the available options and
press the GREEN button when the Select Function option is
highlighted.
3. Key enter the number 36 and press the GREEN button.
You will then be asked to swipe the Supervisor Card or
enter your Supervisor Code through the terminal.
4. To assign the terminal to a base unit press the GREEN
button.
To cancel the operation, press the YELLOW button.
5. Select ASSIGN TO BASE and press the GREEN button.
6. Place the handset onto the base unit if you have not
already done so.
The terminal will display different screens to confirm that the base unit assignment is in progress.
The terminal will finally confirm that the base unit assignment was successful and will
automatically return to the ready prompt after three seconds.
Assigning a Handset to more than one Base
Your handset can be assigned to up to three bases. If you are not in range of your primary base
unit, you can select from two others that the handset is assigned to in order to complete your
transaction. Follow the prompts below to assign your terminal to more than one base.
1. At the READY prompt press the MENU button twice.
2. Use the arrow buttons to view the available options and
press the GREEN button when the Select Function option is
highlighted.
3. Key enter the number 36 and press the GREEN button.
You will then be asked to swipe the Supervisor Card or
Page 34
Print Transaction Log
Continue?
Enter=YES Clear=NO
SYSTEM MENU
Totals
Print Function Codes
Select Function
Key in Function Code
and then press ENTER
SYSTEM
Radio Setup?
Enter=YES Clear=NO
RADIO SETUP
Assign to base
Select base
Remove base
SYSTEM MENU
Totals
Print Function Codes
Select Function
Key in Function Code
and then press ENTER
4.

Installing the Bluetooth Terminal

• Ensure the mains supply is connected to the terminal and switched off.
• Ensure you have your Merchant ID to hand. This can be found on your Welcome Letter.
• Place the terminal handset onto the base if you have not already done so.
Now switch on the mains supply.
Dual Comms Mode
Using the arrow keys to highlight the required option and
then press ENTER to select that option.
The terminal will display this screen, press the GREEN
button and a number of additional screens will be
displayed while the handset assigns to the base.
At this screen press the GREEN button and the installation
process will continue.
If your terminal is connected via a direct line, press the YELLOW button to select NO.
If your phone line is connected to a Switchboard/PBX, press the GREEN button to select YES.
1. Key in your merchant number and press the GREEN
button. The terminal will start to dial the Host computer
and a number of communication messages will be
displayed.
2. The terminal will now contact each card acquirer which
your terminal is configured to accept.
Further communications messages will be displayed. An
installation report will then be printed displaying the
card types that your terminal will accept.
3. Finally, the terminal will dial the Host computer to
report the successful installation.
4. Installation is now complete and the terminal will
display the READY prompt. Your terminal is now ready for
use.
Check the date and time on your terminal, if this needs to be corrected refer to Section 36 of this
guide for detail on how to do this.
5.

Installing the GPRS Terminal

• Ensure the mains supply is connected to the terminal and switched off.
• Ensure you have your Merchant ID to hand. This can be found on your Welcome Letter.
• Place the terminal handset onto the base if you have not already done so.
PLACE TERMINAL ON A BASE
WITH A PHONELINE and press
ENTER
Connection Method
Telephone <PPP>
LOCAL NETWORK
Terminal Installation
Key in Merchant No.
and then press Enter
READY
Merchant Number
12345678
Page 7