Konftel 300IP Manual page 60

1. 7100 dials 1100 1100 answers7100 on-hook after 120s
2. 1100 dials 71007100 answers1100 on-hook after 120s
3. 7101 dials 1100 1100 answers7101 hits "Hold" after 20s
4. 7101 hits "Resume" after 20s1100 on-hook after 120s
5. 1100 dials 234-80008000 answers8000 on-hook after 90s
6. 7100 dials 11001100 answers 1100 hits "Transfer" after 20s
7. 1100 dials 71011100 hits "Transfer 1100 on-hook
8. 7100 goes on-hook after 120s
9. 1100 dials 71007100 answers7100 hits "Transfer" after 20s
10. 7100 dials 234-80008000 answers
11. 7100 hits "Transfer" after 30s7100 on-hook
12. 8000 goes on-hook after 120s
13. 1100 dials 71017101 answers
14. 7101 hits "Conference" after 30s7101 dials 234-8000
15. 8000 answers7101 hits "Conference" after 30s
16. 7101 goes on-hook after 120s
17. 1100 and 8000 goes on-hook after 200s
18. Repeat steps 1-17 by replacing DN:1100 with DN(s) of other
Cisco phone models
19. Retrieve CDR from CUCM
20.Check Calling, Called, Duration, Origination & Termination
Cause Codes
Test Case #
Objective
Pre-Test Conditions
•
Local CUCMDUT(s):7100 & 7101; SCCP:1000; SIP:2000;
•
Remote CUCM DUT:8000; SIP:6200; SCCP:5200;
•
RPC is used to remotely control IP Phones with DN: 1000,2000;
•
Assumption: DUT is Advanced 3
Test Procedure
1. Provision all the lines for both 7100 & 7101
DevicePhoneDNLine (DN Range: 7120 -7150)
2. Initiate calls on all the lines between 7100 & 7101
3. Calling & Called parties goes on-hook alternatively at random
duration
4. Initiate intra-cluster & inter-cluster calls on all lines to SIP, SCCP
& PSTN endpoints
5. Calling & Called parties goes on-hook alternatively at random
Duration.
6. Initiate calls and perform mid-call features between these lines
(Hold/Resume, Transfer, Conference, CFNA, CFB)
7. Retrieve CDR from CUCM
8. Check the Calling, Called, Duration, Origination & Termination
Cause Codes
© 2014 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Test Procedure
Test Results: Comments
EP-56
Category Functional Test: Multiple Lines
Verify DUT is able to handle calls and mid-call features on multiple lines
rd
Party SIP Endpoint with multiple lines
Test Results: Comments
Expected Results
•
Intra-cluster calls establish between DUT & Cisco IP Phone
•
Inter-cluster calls establish between DUT & Cisco IP Phone
•
Call Hold/Resume between DUT & Cisco IP Phone
•
Blind Transfer between DUT & Cisco IP Phone
•
Consult Transfer between DUT & Cisco IP Phone
•
Conference Call between DUT & Cisco IP Phone
•
CDR(s) retrieved for all the calls
•
Selected fields in CDR(s) match calls
Note:
Any Cisco IP Phone models not supported in RPC will have Auto
Answer Turned On to test basic call functions only.
P
x
Expected Results
•
All calls establish successfully with good audio quality
•
Caller ID presented for all calls
•
Mid-call features works as designed
•
All calls release normally
•
CDR (s) retrieved
•
Selected fields in CDR match calls
P
x
F N/A N/S N/T B
RFC_Standard Y
F N/A N/S N/T B
Page 60 of 64