ZN-BT662XE-MIR Installation Guide INFORMATION TO USER CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL. This symbol is intended to alert the user to the presence of un-insulated “dangerous voltage”...
ZN-BT662XE-MIR Installation Guide 1. FEATURES Camera Indoor/Outdoor IR Bullet IP Camera 1/2.7” 1080p CMOS ICR type true day & night ONVIF Support (End of Aug) Streaming Dual streaming mode (such as different codec/resolution/bit rate and so on.) ...
ZN-BT662XE-MIR Installation Guide 2. PACKAGE CONTENTS Unpack carefully and handle the equipment with care. The packaging contains: Camera Video out cable Hex wrench driver Screws Quick installation Guide DC power adaptor Terminal block Screw anchors The above contents are subject to change without prior notice.
ZN-BT662XE-MIR Installation Guide 3. PART NAMES ① ④ IPN6602HD-5311 ⑤ ⑥ Cable arrange ② A : DO- ③ TELE B : DO+ WIDE NEAR NT/PAL VOUT C : DI+ D : DI- ⑦ * Models herein and their appearance are subject to ⑧...
Page 7
ZN-BT662XE-MIR Installation Guide Use this part for tilting adjustment. Refer to 4. Installation for more details. ⑦ 4 Pin Connector A: DO,- B: DO+, C: DI+, D: DI- ⑧ Power Adaptor Connector The camera needs DC 12V for power supply.
ZN-BT662XE-MIR Installation Guide 4. INSTALLATION Place the installation template that is provided in the package on the desired position of installation. Drill four holes on the template and insert anchor blocks into the holes. Fasten the camera with screws. Make sure the cables are properly connected to the camera.
ZN-BT662XE-MIR Installation Guide 4.2. Adjusting LED options and lens focus Adjust the zoom and focus of the lens with the lever of ① and ② on the following picture. IPN6602HD-531 TELE WIDE NEAR NT/PAL RESET TELE VOUT WIDE NEAR NT/PAL...
ZN-BT662XE-MIR Installation Guide 5. CABLE CONNECTIONS Cable arrange A : DO- B : DO+ C : DI+ D : DI- DI/DO Power DC 12V LAN Port Red : AIN Audio In White : AOUT Audio Out DI/DO Connection A: DO-, B: DO+ , C: DI+ , D: DI- Sensor (DI) connection The camera provides 1 channel D/I.
Page 12
ZN-BT662XE-MIR Installation Guide Internal +3.3V Internal Output of Output of Sensor Sensor Relay Type Voltage Type Alarm (DO) connection Only the relay type is supported. Relay Rating: Max 24VDC 50mA Do not exceed the maximum relay rating. Caution Internal Device...
Page 13
ZN-BT662XE-MIR Installation Guide Do not connect the speaker without amplifier. Caution 01A.01...
ZN-BT662XE-MIR Installation Guide 6. CONFIGURATION 6.1.Set up network environment The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address from the MAC address of your device. Please make sure the device and your PC are on the same network segment before running the installation.
Page 15
ZN-BT662XE-MIR Installation Guide To use the IPAdminTool and view the live video on a web page: 1. Start IPAdminTool. Names and info of currently activated devices appear as a list. 2. Right-click on the desired device and select Web view.
ZN-BT662XE-MIR Installation Guide 6.2.2. View video using IP address View the live video on a web page using your IP device and its IP address. To have the correct IP address ready and use it on a web page: 1. Convert a MAC address to an IP address or check the IP address on the IPAdminTool. Refer to Appendix (D): Hexadecimal-Decimal Conversion Table.
ZN-BT662XE-MIR Installation Guide APPENDIX (C): HEXADECIMAL-DECIMAL CONVERSION TABLE Refer to the following table when you convert the MAC address of your device to IP address. Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec 94 148...