Safety Regulations; General Safety Rules - WAGNER PEM-C2 Operating Manual

1.1

Safety regulations

This equipment can be dangerous if it is not operated in accordance with
this operating manual! There might be additional regulations to be
observed, put into effect by governmental, state or other official agencies
Warning
or local security (fire) departments!
The following rules must be observed in order to ensure a safe and efficient use of the
equipment:
•
Under no circumstance may persons with a cardiac
pacemaker come close to the area between the tip of
the spraygun and the workpiece to be coated!
•
The user has to observe particularly the safety
guidelines of the VdS or the local professional and
security institutions. 2) 3) 6) 9)
•
The spraygun may only be operated in the hazard zone
created by operation of the manual spraying equipment
itself. 2) 3) 6)
•
The spraygun may only be operated in powder spray
booths or powder spray benches equipped with
industrial ventilation. 2) 3) 6
•
The user has to ensure that the medium value of the
powder/air concentration does not exceed 50% of the
LEL (maximum allowed concentration of powder in air).
If the LEL is not known, the user should assume a value
of 20 g/m³. 2) 3) 6)
•
The main power connection for operation of the Wagner
powder equipment must be electrically interlocked with
the exhaust system of the powder coating booth. 2) 3) 6)
•
The Wagner control unit must be installed outside the
hazard area. 2) 3)
x) See paragraph 9.1 "Applicable safety regulations and list of sources"
1.2

General safety rules

•
Keep your workplace well organized
A disorganized workplace creates a hazard.
•
Take the environmental influences into
consideration
Do not expose the manual system to rain. Do not use the
manual system in a damp or wet environment. Ensure
good illumination. Do not use power tools near
flammable liquids or gases.
•
Store your tools carefully
Unused tools should be stored in a dry, locked room and
out of the reach of unauthorized persons.
•
Do not use the cable for purposes other than those
intended
Do not carry the spraygun by the cable and do not use it
to pull the plug out of the socket. Protect the cable from
heat, oil and sharp objects.
•
Do not over-reach your standing position
Avoid abnormal body positions. Ensure stable footing
and always keep your balance.
•
Wear suitable work clothing
02/01
PEM-C2
•
The user must conduct periodic checks of the powder
spray equipment (at least every year) with regard to
explosion-protection. 5) 7)
•
In the event of faults or defects, repair work is to be
performed at the user's discretion. 7)
•
The user must keep a test certificate of the device type
on file at the installation site. 7)
•
The execution of repairs must not lead to an alteration in
the explosion-protection. 5) 7)
•
Repairs may only be carried out by specially trained
personnel. 7)
•
Repairs must never be performed in an explosion-
hazard area. 7)
•
The work area must have an electrostatically conductive
floor (measured in accordance with DIN 51953) 2) 3) 6)
•
All conductive parts in the work area must be
electrostatically grounded (work area = 1.5 m at the
sides, 2.5 m to the front and rear of every spray location
or opening in the booth). 2) 3)
•
All persons inside the work area must wear
electrostatically conductive footwear. 2) 3)
•
If gloves are used, they must be of antistatic material or
have cut-out palm areas. 2) 3)
•
Use breathing protection
Use breathing protection for work which produces
powder.
•
Take good care of the system
Keep the system clean to ensure that it works well and
safely. Check the plug and line cord regularly and have
them replaced by customer service if damaged. Check
the extension cord regularly and replace it when
damaged.
•
Always remain alert
Watch your work. Proceed in a reasonable manner. Do
not use tools when you lack concentration.
•
Check your equipment for damage
Before using the system, carefully inspect slightly worn
parts for proper operation. Check whether the moving
parts operate properly, whether they jam and whether
parts are damaged.
All parts must be properly assembled in order to ensure
proper operation of the unit. Damaged parts should be
repaired or replaced by a Wagner customer service.
6
0351801