Page 1
Operating Manual Tribo Manual Spray Gun DANGER High Voltage! Turn power off before servicing! CAUTION Read rules for safe operation and instructions carefully! pemt3_0000 PEM-T3 0351967 03/2008 0351709...
Page 2
D Spray gun body H Power supply The Tribo manual spray gun PEM-T3 is used for powders suitable for friction loading. The PEM-T3 powder spray gun is used for industrial powder coating. This spray gun can be operated with the following control units: •...
Technical data ......................17 Warranty........................18 Scope of delivery and spare parts lists..............19 How to order........................19 Scope of delivery and spare parts list of PEM-T3 ............19 Charging body (complete) ...................20 Wide fan spray nozzle ....................20 Gun extension ......................21 Charging body of PEM-T3 300..................22 Outer tube ........................23...
Page 4
The user must obey all the rules of operation found in this manual; failure to do so will render the warranty invalid. Wagner powder systems are designed to meet the most stringent safety requirements. They can be operated in compliance with generally applicable safety codes and applicable national safety regulations.
Spray guns should be operated with bare hands! • The main power connection for operation of the If gloves are used they must be made of Wagner powder equipment must be electrically conductive material. interlocked with the exhaust system of the •...
BGI 764 The product includes an EC declaration of conformity. This can be ordered again if necessary from your WAGNER dealer by giving details of the product and serial number involved. The number of the EC Declaration of Conformity is 0351967.
Before you start making connections, switch off the powder feeding. Refer to the operating instructions of the corresponding control unit for this. Tribo air from the control unit Powder feed to the electrical connection from the powder injector at the control unit pemt3_0003 0351709 03/2008 - PEM-T3...
• uneven coating • very bad wrap around Warning Sparks between workpiece and conveyor hooks (hangers) can occur if hooks or other hanger parts are not completely cleaned! These sparks can cause heavy radio frequency interference. 0351709 03/2008 - PEM-T3...
• Press the trigger on the spray gun so that the spray gun is blown free of powder. • Switch off the control unit and secure against inadvertent switch on. 0351709 03/2008 - PEM-T3...
Carefully re-fit the charging body 5 and the nozzle body 4 in the gun housing 3 and tighten it up with the outer nut 2 . • Slide the deflector cone 1 onto the charging body 5 again. The spray gun is again ready for operation. 0351709 03/2008 - PEM-T3...
J . • Disconnect the powder feed hose G and Tribo air hose F from the spray gun D . Pemt3_0004 • Exchange the spray gun for a new one and assemble it in reverse order. 0351709 03/2008 - PEM-T3...
• Complete clean residual powder from all parts. • Replace worn parts with new ones. • Reassembly of the charging body. • Carefully push the charging body back into gun and reassemble the gun. Pemt3_0006 0351709 03/2008 - PEM-T3...
Pull the deflector cone/fan spray nozzle 1 from the nozzle body 3. • Unscrew the outer nut 2 from the gun housing. • Pull the nozzle body 3 from the gun housing. P_00716 • Pull out the charging body 4 from the gun housing. 0351709 03/2008 - PEM-T3...
Page 14
Insert charging body 6 into the outer tube 5 and push it in as far as it will go. • Push adapter 7 onto outer tube 5 as far as it will go. • Locate deflector cone / column nozzle 1 onto adapter 7. 0351709 03/2008 - PEM-T3...
Wagner or one of our dealers will take back your used Wagner waste electrical or electronic equipment and will dispose of it for you in an environmentally friendly way. Please ask your local Wagner service center or dealer for details or contact us direct.
- Inadequate or no powder (e.g. no wraparound charging or no powder adhe- - Electrical cable from spray gun - Contact Wagner Service sion) to control unit faulty - Tribo current measuring or display module defective - Powder-conveying parts in...
For volumes, specified in Nm (standard cubic meters). One cubic meter of a gas at 32 °F (0 °C) and 1.013 bar is called norm cubic meter. 1 Nm /h = 35.3 ft /h; 1 bar = 14.504 psi 0351709 03/2008 - PEM-T3...
If Wagner is unable to repair this product so as to conform to this Limited Warranty after a reasonable number of attempts, Wagner will provide, at our option, either a replacement for this product or a full refund of the purchase price of this product.
Invoicing address Delivery address Name of contact persons for check back Type of delivery Quantity ordered, article number and designation Scope of delivery and spare parts list of PEM-T3 0351019 Item Art. No. Designation 0351019 Tribo manual gun PEM-T3 Deflector cone ( ∅...
Item Art. No. Designation 0260926 * Wide fan spray nozzle ** 0260280 * Wide fan spray nozzle 9971037 * O-ring 22x1,5 Deflector cone ∅ 13 0260627 * Wearing part ** Only available as a set 0260926_et 0351709 03/2008 - PEM-T3...
Scope of delivery and spare parts lists Charging body of PEM-T3 300 P_00720 Item Art. No. Designation 0260935 Charging body PEM-T3 300 0260632 * Air nozzle (complete) 0260463 * Central air supply 0260469 * Deflector cone rod 0260470 * 0260471 *...