Mitsubishi LANCER 2012 Manual

page of 723

/ 723
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Introduction

Thank you for buying a MITSUBISHI LANCER.

We are confident you will enjoy your vehicle. It has been engi-

neered for optimum performance, durability and comfort. By

thoroughly reading this Owner's Manual, you will gain an

understanding of the many features that are included in the

LANCER. The Owner's Manual contains descriptions and

illustrations that will assist in the operation and maintenance of

your vehicle.

Your Authorized Mitsubishi Motors Dealer will be happy to

assist you with any further questions you may have regarding

the operation of your vehicle.

Please note that this manual applies to all LANCER models

and explains all features including options. Some features

explained in this manual may not be installed on your vehicle.

Please leave this Owner's Manual in the vehicle at the time of

resale. The next owner will appreciate having access to the

information contained here.

This manual includes instructions for standard and optional

equipment available at the time of printing. Mitsubishi Motors

Corporation reserves the right to make changes in design and

Specifications and to make additions or improvements in its

product without assuming any obligation to install these on

previously manufactured products.

Throughout this manual the words WARNING and CAUTION

appear.

N09200100891

These are reminders to be especially careful. Failure to follow the

instructions could result in personal injury or damage to your

vehicle.

WARNING

Indicates a strong possibility of severe personal injury or

death if instructions are not followed.

CAUTION

Points out hazards or unsafe practices that could cause minor

personal injury or damage to your vehicle.

You will see another important symbol:

NOTE Gives helpful information.

WARNING

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals

known to the State of California to cause cancer and

birth defects and reproductive harm. In addition,

certain fluids contained in vehicles and certain prod-

ucts of component wear contain or emit chemicals

known to the State of California to cause cancer and

birth defects or other reproductive harm.

I n f o r ma t i o n P r o v i d e d b y :

Printed in Japan

Table of Contents

Summary of Contents for Mitsubishi LANCER 2012

Page 1 CAUTION Your Authorized Mitsubishi Motors Dealer will be happy to assist you with any further questions you may have regarding Points out hazards or unsafe practices that could cause minor the operation of your vehicle.
Page 2: Table Of Contents
Table of contents Overview Quick index General information Seat and restraint systems Features and controls Driving safety Comfort controls For emergencies Vehicle care and maintenance Customer assistance/ Reporting Safety Defects Specifications I n f o r ma t i o n P r o v i d e d b y :...
Page 3 Overview Instruments and controls (Driver’s area) N00100201286 Except for RALLIART Instrument cluster P.3-178 Sportronic steering wheel paddle Multi-information meter switch P.3-182 shifter (if so equipped) P.3-106 Combination headlights and dimmer switch P.3-234 Wiper and washer switch Turn signal lever P.3-243 P.3-246 Front fog light switch (if so equipped) P.3-245...
Page 4 Overview RALLIART Instrument cluster P.3-178 Sportronic steering wheel paddle Multi-information meter switch P.3-182 shifter P.3-125 Combination headlights and dimmer switch P.3-234 Wiper and washer switch Turn signal lever P.3-243 P.3-246 Front fog light switch P.3-245 Cruise control switches Steering wheel audio remote P.3-157 control switches P.5-134 Ignition switch P.3-85...
Page 5 Overview Instruments and controls N00100201387 Except for RALLIART Supplemental restraint system - airbag Gearshift or selector lever P.3-94, 3-98 (for front passenger’s seat) P.2-34 Vents P.5-2 Glove com- partment P.3-298 USB input terminal (if so equipped) P.3-283 Parking brake lever P.3-77 Drive mode-selector (if so equipped) P.3-136 Trunk lid release...
Page 6 Overview Supplemental restraint system - airbag RALLIART Gearshift lever P.3-112 (for front passenger’s seat) P.2-34 Vents P.5-2 Glove com- partment P.3-298 USB input ter- minal (if so equipped) P.3-283 Parking brake lever P.3-77 ACD control mode Trunk lid release Cup holder (for front switch P.3-133 lever P.3-59 seats) P.3-302...
Page 7 Digital clock (if so equipped) P.5-149 Digital clock (if so equipped) P.5-149 Mitsubishi Multi-Communication System (if so Mitsubishi Multi-Communication System (if so equipped) Refer to the separated “Mitsubishi equipped) Refer to the separated “Mitsubishi Multi-Communication System owner’s manual” Multi-Communication System owner’s manual”...
Page 8 Overview Interior N00100301173 Electric remote- Dome light (Front)/Reading lights Sunroof switch controlled out- (if so equipped) P.3-292, 7-58, 7-85 (if so equipped) Window lock switch P.3-73 side mirror switch P.3-74 P.3-83 Power window Power door lock switches P.3-69 switch P.3-55 ®...
Page 9 Overview Supplemental restraint system - curtain airbag (if so equipped) P.2-52 Coat hook (if so equipped) Dome light (Rear, if so equipped) P.3-294, P.3-304 7-58, 7-86 Assist grip P.3-304 Rear seat P.2-8 Tether anchors for child restraint Cup holder (for rear seat, if so equipped) P.3-303 system P.2-28 Arm rest (if so equipped) P.2-9 I n f o r ma t i o n P r o v i d e d b y :...
Page 10: Trunk Lid Release Lever P
Overview Trunk area N00100500413 Inside emergency trunk lid release Trunk area light P.7-58, 7-88 lever P.3-62 Spare tire P.6-10 AWC control fluid res- ervoir (RALLIART) P.7-20 Jack P.6-8 Tools P.6-7 I n f o r ma t i o n P r o v i d e d b y :...
Page 11 Overview Outside (Front) N00100601163 Locking and unlocking P.3-51 Except for RALLIART Sunroof (if so equipped) P.3-74 Keyless entry system Windshield wiper and washer (if so equipped) P.3-9 P.3-246 F.A.S.T.-key (Free-hand Advanced Security Transmitter) Engine compartment P.7-7 (if so equipped) P.3-17 Engine hood P.7-4 Fuel tank filler P.1-4...
Page 12 Overview Locking and unlocking P.3-51 RALLIART Sunroof (if so equipped) P.3-74 Keyless entry system (if so equipped) P.3-9 Windshield wiper and washer F.A.S.T.-key (Free-hand P.3-246 Advanced Security Transmitter) Engine compartment P.7-7 (if so equipped) P.3-17 Engine hood P.7-4 Fuel tank filler P.1-4 Outside rearview mirrors P.3-83 Side turn-signal lights P.3-243, 7-55...
Page 13 Overview Outside (Rear) N00100601277 Except for RALLIART Tire inflation pressure P.7-32 Changing tires P.6-9 Antenna P.5-148 Tire rotation P.7-35 Wheel covers (if so equipped) P.6-20 Tire chains P.7-37 High-mounted stop light P.7-55 Tire pressure monitoring system P.3-166 Trunk lid P.3-59 Rear-view camera (if so equipped) P.3-172...
Page 14 Overview RALLIART Antenna P.5-148 Tire inflation pressure P.7-32 Changing tires P.6-9 Tire rotation P.7-35 High-mounted stop light P.7-55 Tire chains P.7-37 Tire pressure monitoring system P.3-166 Trunk lid P.3-59 Rear-view camera (if so equipped) P.3-172 Trunk lid OPEN switch P.3-21 Rear side-marker lights P.3-234, 7-55, 7- License plate lights Rear turn-signal lights P.3-243, 7-55, 7-79...
Page 15 I n f o r ma t i o n P r o v i d e d b y :...
Page 16 If the brake fluid level is correct, there may be a system malfunction. Avoid hard braking and high speeds, and contact an authorized Brake warning light Mitsubishi Motors dealer or a repair facility of your choice for assis- tance. Although your vehicle will usually be drivable and not need towing, have the engine system checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible.
Page 17 Anti-lock braking system warning light Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. It is not necessary to stop the vehicle immediately, but we recommend P.2-22,...
Page 18 Quick index If this problem occurs... N00200900838 Problem Do this Ref. Page When using a key to start the engine Cannot turn the key. Will not turn from “LOCK” to “ACC”. (When using a key to start the Turn the key while turning the steering wheel in either direction. engine) Will not turn from “ACC”...
Page 19 Quick index Problem Do this Ref. Page Cannot shift the selector lever (CVT) or the gearshift lever (Twin Shift the selector lever (CVT) or the gearshift lever (Twin Clutch SST) while press- Clutch SST) from the “P” (PARK) ing the brake pedal. P.3-98, 3-112 position.
Page 20 Quick index Problem Do this Ref. page The engine coolant temperature display “ ” in the multi-informa- tion display is flashing. Steam comes out of the engine compartment. Type 1 The engine is overheated. P.6-5 Carefully stop the vehicle in a safe place. Type 2 1.
Page 21 Mitsubishi Motors dealer. (for vehicles with CVT) Twin Clutch SST does not shift. Vehicle cannot move.
Page 22 Quick index Problem Do this Ref. page A tire is punctured. 1. Park the vehicle in a safe place where the surface is flat and level. P.6-9 2. Replace the flat tire with the spare tire. I n f o r ma t i o n P r o v i d e d b y :...
Page 23 I n f o r ma t i o n P r o v i d e d b y :...
Page 24: General Information
Filling the fuel tank ......1- Modifications to and racing of your vehicle ..1- Mitsubishi Motors genuine parts ....1- California Perchlorate Materials Requirements. . .1- 10...
Page 25: Fuel Selection
General information Fuel selection Octane requirement N00301000752 Except for RALLIART Your vehicle is designed to use unleaded gasoline only. It is Your vehicle is designed to operate on unleaded gasoline hav- equipped with a fuel filler tube especially designed to accept ing a minimum octane number of 87 [(MON+RON)/2], or 91 only a small diameter unleaded gasoline dispensing nozzle.
Page 26: Reformulated Gasoline
If this happens, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for I n f o r ma t i o n P r o v i d e d b y :...
Page 27: Filling The Fuel Tank
Be sure to use a genuine Mitsubishi handling it. When refueling your vehicle, always cleaning additive. Using an unsuitable additive could turn the engine off and keep away from flames, make the engine malfunction.
Page 28 General information Fuel tank capacity 3. Open the fuel tank filler pipe by slowly turning the cap counterclockwise. Front-wheel drive vehicles: 15.5 gal (59.0 L) All-wheel drive vehicles: 14.5 gal (55.0 L) Refueling 1. Before filling with fuel, stop the engine. 2.
Page 29 General information 4. While filling with fuel, store the cap in the cap holder 6. When the nozzle stops automatically, do not attempt to located on the inside of the fuel tank filler door. add more fuel. CAUTION To avoid fuel spillage and overfilling, do not “top- off”...
Page 30: Modifications To And Racing Of Your Vehicle
Mitsubishi Motors dealer or a repair facility of your DAMAGE OR PERFORMANCE PROBLEMS RESULT- choice as soon as possible. ING FROM MODIFICATIONS TO OR RACING OF YOUR VEHICLE ARE NOT COVERED UNDER WAR- RANTY.
Page 31 Only Mitsubishi Motors approved accessories should be always possible for an authorized Mitsubishi Motors dealer to fitted to your vehicle. check whether the attachment or installation of non-Mitsubishi Improper installation of electrical parts could cause fire.
Page 32: Mitsubishi Motors Genuine Parts
Also available from Mitsubishi Motors dealer before installation of any accessory your Mitsubishi Motors dealer are a wide variety of accessories which may involve modification of the electrical or fuel sys- to personalize your new vehicle. Each Mitsubishi vehicle has a tems.
Page 33 General information California Perchlorate Materials Require- ments N00300100017 Certain components of this vehicle, such as airbag modules, seat belt pretensioners, and button cell batteries, may contain perchlorate materials. Special handling may apply. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate. I n f o r ma t i o n P r o v i d e d b y : 1-10...
Page 34: Seat And Restraint Systems
Seat and restraint systems Seats ........2- Seats and restraint systems.
Page 35 Seat and restraint systems Seats N00408400479 1 - Front seats 2 - Rear seats To adjust the seat forward or backward → P.2-5 Folding the seatbacks forward (if so equipped) → P.2-8 To adjust the seatback → P.2-5 Arm rest (if so equipped) → P.2-9 To adjust the seat height (Driver’s side only, if so equipped) →...
Page 36: Seats And Restraint Systems
Seat and restraint systems Seats and restraint systems Front seats N00401600182 N00401800315 Your vehicle has seat belts and other features that help protect Position the driver’s seat as far back as possible while main- you and your passengers in an accident. taining a position that still enables you to fully apply the ped- Seat belts are the most important safety device.
Page 37 Seat and restraint systems WARNING CAUTION Do not attempt to adjust the seat while driving. This Make sure that the seat is adjusted by an adult. If it can cause loss of vehicle control and result in an is adjusted by a child, an unexpected accident might accident.
Page 38 Seat and restraint systems To adjust the seat forward or backward To adjust the seatback N00401900244 N00402000297 Pull the seat adjusting lever up and slide the seat forward or Except for RECARO seat backward to the desired position. Release the adjusting lever to To adjust the seatback, lean forward slightly, gently pull the lock the seat in place.
Page 39 Seat and restraint systems To adjust the seat height (Driver’s side only, if so RECARO seat Adjust the seatback angle by turning the dial. equipped) N00402100184 Operate the lever repeatedly to raise or lower the seat. 1- To move to forward direction 2- To recline backward 1- Raise WARNING...
Page 40 Seat and restraint systems Heated seats (if so equipped) WARNING N00435600336 The heated seats can be operated when the ignition switch is in Persons who are unable to feel temperature change the “ON” position. or skin pain due to age, illness, injury, medication, alcohol use, fatigue or other physical conditions or who have sensitive skin may suffer burns when using the heated seat even at low temperatures.
Page 41: Rear Seats
Seat and restraint systems Rear seats WARNING N00402500162 Do not allow anyone to ride in the luggage compart- Folding the seatbacks forward (if so equipped) ment while the vehicle is in motion. People who are not properly seated and restrained can be seriously N00402900195 The rear seatbacks can be folded forward to provide additional injured or killed in an accident.
Page 42: Head Restraints
Seat and restraint systems Arm rest Head restraints (if so equipped) N00403000294 N00404300539 Tilt the arm rest down for use as shown. Except for RECARO seat The arm rest includes a cup holder. (Refer to “Cup holder” on page 3-302.) N00409400030 Padded head restraints for the seats can reduce the risk of a whiplash injury if your vehicle is hit from the rear.
Page 43 Seat and restraint systems Adjustment of the head restraint height WARNING To reduce the risk of injury in an accident, adjust the head In order to minimize the risk of a neck injury due to restraint height so that the center of the restraint is at your eye a rear impact, the head restraint must be adjusted to level when seated.
Page 44 Seat and restraint systems To remove CAUTION Press the lock knob (A) in the direction shown by the arrows. Then pull the head restraint up and out of the seatback. Check that the lock knob (A) is extended out as shown in the illustration.
Page 45 Seat and restraint systems RECARO seat CAUTION N00409500044 RECARO seats are equipped with padded head restraints inte- The shape and size of the head restraint differs grated with the seatbacks. These head restraints can reduce the according to the seat. Always use the correct head risk of a whiplash injury if your vehicle is hit from the rear.
Page 46: Seat Belts
Seat and restraint systems Seat belts WARNING N00406000439 In order to minimize the risk of a neck injury due to Seat belts are installed in your vehicle to help reduce the risk of a rear impact, the driver and front passenger seat- injury to the driver and passenger in the event of an accident.
Page 47: Seat Belt Instructions
In the event of an accident, all seat belt assemblies, including retractors and attachment hardware, should be inspected by an authorized Mitsubishi Motors dealer to determine whether replacement is necessary. I n f o r ma t i o n P r o v i d e d b y :...
Page 48 Seat and restraint systems 1. Occupants should always sit back in their seats with their WARNING backs against the upright seatback. To reduce the risk of To reduce the risk of serious injury or death in the serious injury or death during deployment of the airbag, event of an accident or sudden stop, all seatbacks adjust the driver’s seat as far back as possible while main- should be kept in the upright position while the vehi-...
Page 49 Seat and restraint systems 2. Grasp the latch plate and slide it up the webbing so that it 3. Pull the seat belt out slowly while holding the latch plate. easily pulls across your body. Push the latch plate into the buckle until you hear a “click”.
Page 50 Seat and restraint systems NOTE 4. The lap part of the belt must always be worn low and snug With the exception of the seat belt for the driver, the seat across the hips. Pull up on the shoulder portion of the belt belts in all other seating positions are equipped with an to take up any slack in the lap belt.
Page 51 Seat and restraint systems Driver’s seat belt reminder/warning light and If you then repeatedly stop and start your vehicle with the seat belt unfastened, the warning light/display and tone will remind display you to fasten your seat belt every time the vehicle starts mov- N00418400300 ing.
Page 52: Front Passenger Seat Belt Warning Light
Seat and restraint systems Front passenger seat belt warning light Adjustable seat belt shoulder anchor (front seats) N00418300165 N00406300315 The front passenger seat belt warning light is located in the To move the anchor down, press the lock knob (A) and slide instrument panel.
Page 53: Seat Belt Extender
Seat and restraint systems Seat belt extender WARNING N00406700087 When your seat belt, even fully extended, is not long enough, a Always adjust the shoulder belt anchor so that the seat belt extender must be obtained. The extender may be used shoulder belt is positioned across the center of your shoulder without touching your neck.
Page 54: Seat Belt Use During Pregnancy
Seat and restraint systems Seat belt use during pregnancy Seat belt pre-tensioner and force limiter systems N00406800121 Seat belts work for everyone, including pregnant women. Like N00417700609 all occupants, pregnant women are more likely to be seriously The driver’s and front passenger’s seats each have a seat belt injured or killed in an accident if they do not wear seat belts.
Page 55: Srs Warning
2- Front impact sensors pre-tensioner system inspected by an authorized 3- Seat belt pre-tensioners Mitsubishi Motors dealer. 4- Airbag control unit 5- Side impact sensors SRS warning The airbag control unit monitors the readiness of the electronic parts of the system whenever the ignition switch is in the “ON”...
Page 56: Child Restraint Systems
Seat and restraint systems Force limiter system Child restraint systems N00408900113 N00407100697 In the event of an accident, the seat belt force limiter system When transporting infants or small children in your vehicle, an will help reduce the force applied to the driver and front seat appropriate child restraint system must always be used.
Page 57 Seat and restraint systems Guidelines for child restraint system selection WARNING Any child who is too large to use a child restraint All children should be properly restrained in a restraint device system should ride in the rear seat and wear the lap that offers the maximum protection for their size and age.
Page 58 Seat and restraint systems WARNING WARNING Never hold an infant or child in your arms or on Your vehicle is also equipped with a front passenger your lap when riding in this vehicle, even when you airbag. are wearing your seat belt. Never place any part of Never put REAR-FACING CHILD RESTRAINT the seat belt you are wearing around an infant or SYSTEMS or INFANT RESTRAINT SYSTEMS in...
Page 59 Seat and restraint systems WARNING WARNING FRONT-FACING CHILD RESTRAINT SYS- It is important to use an approved rear-facing infant TEMS should be used in the rear seat whenever pos- restraint until the infant is one year old (unless the sible. If they must be used in the front passenger infant outgrows the seat sooner).
Page 60 Seat and restraint systems Installing a child restraint system using the NOTE Before purchasing a child restraint system, try installing it LATCH (Lower Anchors and Tethers for chil- in the rear seat to make sure there is a good fit. Because of dren) system the location of the seat belt buckles and the shape of the N00418800131...
Page 61 Seat and restraint systems Tether anchor locations Examples of child restraint systems compatible with the LATCH system N00418900129 Your vehicle has 3 attachment points on the rear shelf, located N00419000185 behind the top of your rear seat. These are for securing a child restraint system tether strap to each of the 3 rear seating posi- tions in your vehicle.
Page 62 Seat and restraint systems Using the LATCH system NOTE In order to secure a child restraint system compatible with N00419100157 1. In order to securely fasten the tether strap, remove the the LATCH system, use the lower anchor points in the head restraint from the location where you wish to install outboard positions of the rear seat.
Page 63 Seat and restraint systems Installing a child restraint system using the seat 3. Open the cover for the tether anchor by pulling it back with your hand as illustrated below (3). belt (with emergency/automatic locking mecha- 4. Latch the tether strap hook (F) of the child restraint sys- nism) tem to the anchor (G) as illustrated below (4) and tighten N00407300367...
Page 64 Seat and restraint systems Installation 3. To activate the ALR child restraint installation function, slowly pull the shoulder part of the belt all the way out of 1. Place the child restraint system in the rear seating posi- the retractor until it stops. Then let the belt feed back into tion.
Page 65 Seat and restraint systems 5. After confirming that the belt is locked, grab the shoulder 6. Open the cover from the tether anchor installation point part of the belt near the buckle and pull up to remove any by pulling it back with your hand as illustrated below (6). slack from the lap part of the belt allowing the slack to 7.
Page 66 Seat and restraint systems Children who have outgrown child restraint sys- 9. Before putting your child in the restraint, push and pull the restraint in all directions to be sure it is firmly secured. tems Do this before each use. If the child restraint system is not N00407600504 firmly secure, repeat steps 1 through 8.
Page 67: Maintenance And Inspection Of Seat Belts
Mitsubishi Motors dealer. Failure to the side impacted in moderate to severe side impact collisions. have an authorized Mitsubishi Motors dealer per- form the work could reduce the effectiveness of the The SRS curtain airbags provide the driver and passengers on...
Page 68 Seat and restraint systems The SRS airbags are NOT a substitute for use of the seat belts. WARNING For maximum protection in all types of accidents, seat belts must ALWAYS be worn by everyone who drives or rides in IT IS VERY IMPORTANT TO BE PROPERLY SEATED.
Page 69 Seat and restraint systems WARNING WARNING Airbags inflate very quickly and with great force. Infants and small children should never ride unre- Do not sit on the edge of the seat or sit with your strained, or lean against the instrument panel. They lower legs too close to the instrument panel, or lean should never ride held in your arms or on your lap.
Page 70 Seat and restraint systems WARNING WARNING NEVER put REAR-FACING CHILD RESTRAINT FRONT-FACING CHILD RESTRAINT SYS- SYSTEMS or INFANT RESTRAINT SYSTEMS in TEMS should be used in the rear seat whenever pos- the front passenger seat. This places the infant too sible.
Page 71 Seat and restraint systems How the Supplemental Restraint System works WARNING N00407800463 The SRS includes the following components: Older children should be seated in the rear seat with their seat belt properly worn, and with an appropri- ate booster seat (including a booster cushion) if needed.
Page 72 Seat and restraint systems When the impact sensors detect a front or side impact sufficient to deploy the airbag(s), the appropriate airbag(s) will be deployed. When airbags deploy, some smoke is released accompanied by a loud noise. The smoke is not harmful, but do not intentionally inhale the smoke as it may cause temporary irritation to people with respiratory problems.
Page 73: Event Data Recording
If the vehicle is involved in a severe impact, have the SRS sensor inspected by an authorized Mitsubishi Motors dealer as soon as possible. I n f o r ma t i o n P r o v i d e d b y :...
Page 74 • Do not use a seat cover or a cushion. immediately have your vehicle inspected by an • Do not modify or replace the seat and seat belt. authorized Mitsubishi Motors dealer as soon as pos- • Do not place luggage or other objects under the sible: seat.
Page 75 N00418100277 If the vehicle is involved in a severe impact, have the The passenger’s airbag off indicator is located in the instru- SRS sensors inspected by an authorized Mitsubishi ment panel. Motors dealer as soon as possible. The indicator normally comes on when the ignition switch is turned to the “ON”...
Page 76 Warning light If any of the following conditions occur, you should immediately have the airbag system in your vehicle inspected by an authorized Mitsubishi Motors dealer as soon as possible: • The passenger’s airbag off indicator comes on Warning display type 1 when an adult is sitting on the front passenger seat.
Page 77 Have your vehi- ment. The driver’s airbag and the front passenger’s airbag are cle checked by an authorized Mitsubishi Motors designed to deploy at the same time. However, the front pas- dealer: senger’s airbag does not deploy when the front passenger seat...
Page 78 Seat and restraint systems Driver’s knee airbag system N00404500010 The driver’s knee airbag is located under the steering wheel. The driver’s knee airbag is designed to deploy at the same time as the driver’s front airbag. I n f o r ma t i o n P r o v i d e d b y : 2-45...
Page 79 Seat and restraint systems Deployment of front airbags N00408000521 The front airbags and driver’s knee airbag ARE DESIGNED TO DEPLOY when… Head-on collision with a solid wall at Moderate to severe frontal impact within speeds of approx. 15 mph (25 km/h) or the shaded area between the arrows higher The front airbags and driver’s knee airbag are designed to...
Page 80 Seat and restraint systems The front airbags and driver’s knee airbag MAY NOT Collision with a utility pole, tree or other narrow objects DEPLOY when … In certain types of front collisions, the front airbags and driver’s knee airbag may not deploy, even if the deformation of the body seems to be large, because the vehicle’s body struc- ture is designed to absorb the impact and deform in order to help protect the occupants.
Page 81 Seat and restraint systems The front airbags and driver’s knee airbag ARE NOT Rear end collision to your vehicle DESIGNED TO DEPLOY when … The front airbags and driver’s knee airbag are not designed to deploy in situations where they cannot provide protection to the occupants.
Page 82 Seat and restraint systems The front airbags and driver’s knee airbag MAY Collision with an elevated median/island or curb DEPLOY when … The front airbags and driver’s knee airbag may deploy if the underside of the vehicle suffers a moderate to severe impact (undercarriage impact).
Page 83 Seat and restraint systems WARNING WARNING Do not attach anything to the steering wheel’s pad- Do not attach accessories to, or put them in front of, ded cover, such as trim material, badges, etc. These the windshield. They could restrict the airbag infla- could strike and injure an occupant if the airbag tion, or strike and injure an occupant, when the inflates.
Page 84 They must promptly be replaced and the entire airbag system must be inspected by an authorized Mitsubishi Motors dealer. RECARO seats I n f o r ma t i o n P r o v i d e d b y :...
Page 85 Seat and restraint systems Curtain airbag system A label is attached to the seatbacks in vehicles with side air- (if so equipped) bags. N00419200145 The curtain airbags are contained in the front and rear pillars and roof side rail. The curtain airbag is designed to inflate only Except for RECARO seat on the side of the vehicle that is impacted, even with no passen- ger in the front seat.
Page 86 Seat and restraint systems WARNING WARNING The side airbag and curtain airbag can cause serious In order to reduce the risk of injury from a deploy- injury or death to anyone too close to the airbag ing side airbag, do not allow any rear seat passen- when it deploys.
Page 87 Work done on or in the vicinity of the side airbag and curtain airbag system components should be done only by an authorized Mitsubishi Motors dealer. Improper work methods can cause acciden- tal side airbag and curtain airbag deployment, or render a side airbag and curtain airbag inoperable.
Page 88 Seat and restraint systems Deployment of side airbag and curtain airbag The side airbag and curtain airbag MAY NOT DEPLOY when … N00408200507 In certain types of side collisions, the side airbag and curtain The side airbag and curtain airbag ARE DESIGNED airbag may not deploy, even if the deformation of the body TO DEPLOY when …...
Page 89 Seat and restraint systems Side impact in an area away from the passenger compartment Oblique side impact Motorcycle or other similar small vehicle collision with the Vehicle rolls onto its side or roof side of vehicle Collision with a utility pole, tree or other narrow object I n f o r ma t i o n P r o v i d e d b y : 2-56...
Page 90 SRS performance and may lead to injury. If your vehicle has received any damage, you should have the SRS inspected by an authorized Mitsubishi Motors dealer to make sure it is in proper working Rear end collision order.
Page 91 Mitsubishi Motor Sales of Canada, Inc. If you decide to junk or scrap your vehicle, we urge you to Customer Relations Department first take it to an authorized Mitsubishi Motors dealer so P.O. Box 41009 that the SRS can be made safe for disposal.
Page 92: Warning Labels
Seat and restraint systems Warning labels [For vehicles sold in Guam] To contact Triple J Enterprises Inc. N00408600341 Occupant restraint warning labels for the SRS are located in call (671) 649-3673 or write to: the vehicle as shown in the illustration. Triple J Enterprises, Inc.
Page 93 Seat and restraint systems * - Located in the passenger’s side as well. I n f o r ma t i o n P r o v i d e d b y : 2-60...
Page 94 I n f o r ma t i o n P r o v i d e d b y :...
Page 95 I n f o r ma t i o n P r o v i d e d b y :...
Page 96: Features And Controls
Features and controls Break-in recommendations ......3- Hill start assist (vehicles with Twin Clutch SST)... . 3- 146 Keys .
Page 97: Break-In Recommendations
Features and controls Break-in recommendations Keys N00508700297 N00508800559 Advanced automobile manufacturing techniques permit you to Type 1 operate your new vehicle without requiring a long break-in Two keys are provided. The keys fit all locks. period of low-speed driving. Keep one in a safe place as a spare key. However, you can add to the future performance and economy of your vehicle by observing the following precautions during the first 300 miles (500 km).
Page 98 Features and controls Type 2 Type 3 Two keys are provided. The keys fit all locks. Two Free-hand Advanced Security Transmitter (F.A.S.T.-key) Keep one in a safe place as a spare key. and two emergency keys are provided. Keep one F.A.S.T.-key and one emergency key in a safe place together as a set of spare keys.
Page 99 If you lose your key, to prevent the theft of the vehicle immediately contact an authorized Mitsubishi Motors dealer. If you notify an authorized Mitsubishi Motors dealer of the key number, they can make a new key. The key num- ber is stamped on the key number plate. Keep the key number plate in a safe place separate from the key itself.
Page 100: Electronic Immobilizer (Anti-Theft Starting System)
Features and controls Electronic immobilizer (Anti-theft starting [Except for vehicles equipped with the Free-hand Advanced Security Transmitter (F.A.S.T.-key)] system) The electronic immobilizer is designed to significantly reduce N00509100689 the possibility of vehicle theft. The purpose of the system is to [For vehicles equipped with the Free-hand Advanced Security immobilize the vehicle if an invalid start is attempted.
Page 101 “ACC” or “LOCK” position. Then try to start the engine again. If the engine does not start, contact an authorized Mitsubishi Motors dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 102: Additional Keys
Registering the ID code can be done by your authorized Do not make any alterations or additions to the Mitsubishi Motors dealer. Or it can be done by yourself (except immobilizer system. Alterations or additions could for vehicles sold in Canada).
Page 103 Features and controls NOTE 1. Insert the first valid key into the ignition switch and turn Perform the operation when the interrupt display screen is the key to the “ON” position for 5 seconds. not showing. The interrupt display screen may prevent 2.
Page 104: Keyless Entry System (If So Equipped)
Features and controls Keyless entry system General information (if so equipped) Your electronic immobilizer operates on a radio frequency sub- N00509000763 ject to Federal Communications Commission (FCC) Rules Press the remote control transmitter buttons to lock or unlock (For vehicles sold in U.S.A.) and Industry Canada Rules (For the doors and to open the trunk lid.
Page 105: To Unlock The Doors
Refer to “Welcome light” on page 3-240. NOTE Number of Condition On a vehicle equipped with a Mitsubishi Multi-Communi- chimes cation System, the functions can be adjusted on the One chime The horn will not sound.
Page 106 LOCK button (1) during this time. NOTE 4. Release in sequence the UNLOCK and LOCK buttons On a vehicle equipped with a Mitsubishi Multi-Communi- within 10 seconds of pressing the LOCK button in step 3. cation System, the functions can be adjusted on the screen.
Page 107 Take your vehicle and all the remaining remote control trans- 3. Press the LOCK button (1) for 4 to 10 seconds and press mitters to your authorized Mitsubishi Motors dealer to have the UNLOCK button (2) during this time. your ID codes programmed again.
Page 108 Registering the ID code can be done by yourself or by your if you have one valid (already registered) remote control trans- authorized Mitsubishi Motors dealer. For you to register the ID mitter by doing the following: code yourself, follow the “Customer remote control transmitter 1.
Page 109: General Information
Operation is subject to the following two conditions. the doors will automatically re-lock. This device may not cause harmful interference. On a vehicle equipped with a Mitsubishi Multi-Communi- This device must accept any interference received, includ- cation System, the functions can be adjusted on the ing interference that may cause undesired operation.
Page 110 4. Remove the old battery. NOTE Be sure to perform the procedure with the Mitsubishi mark facing you. If the Mitsubishi mark is not facing you when you open the remote control transmitter case, the buttons may come out. I n f o r ma t i o n P r o v i d e d b y :...
Page 111 You may purchase a replacement battery at an electric appliance store. Your authorized Mitsubishi Motors dealer can replace the battery for you if you prefer. I n f o r ma t i o n P r o v i d e d b y :...
Page 112 Features and controls Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped) N00503100052 The Free-hand Advanced Security Transmitter (F.A.S.T.-key) enables the doors to be locked and unlocked, the trunk lid to be opened, and the engine to be started simply by carrying it. The F.A.S.T.-key can also be used as the remote control trans- mitter of the keyless entry system.
Page 113 (Keyless entry operations are can accelerate the running down of the battery. Do not possible.) For details, contact an authorized Mitsubishi place near electrical appliances such as televisions or Motors dealer.
Page 114 Features and controls Operating range of the F.A.S.T.-key Operating range for locking and unlocking the doors and for opening the trunk lid N00503200112 When a person enters the operating range of the F.A.S.T.-key The operating range is within about 2.3 feet (70 cm) of the while carrying the F.A.S.T.-key and presses the driver’s or driver’s and front passenger’s door lock/unlock switches, and front passenger’s door lock/unlock switch or the trunk lid...
Page 115 Features and controls Operating range for starting the engine NOTE Only the F.A.S.T.-key that is detectable by the doors and N00503300025 The operating range is the interior of the vehicle. the trunk lid can lock and unlock the doors and open the trunk lid.
Page 116 Features and controls To operate using the F.A.S.T.-key NOTE In cases such as the following, the F.A.S.T.-key does not N00503400143 operate. To lock the doors • There is a F.A.S.T.-key in the passenger compartment While carrying the F.A.S.T.-key, press the driver’s or front pas- •...
Page 117 Features and controls Press the driver’s door lock/unlock switch (A) to unlock only Press the front passenger’s door lock/unlock switch (A) to the driver’s door. unlock all the doors. Within about 2 seconds, press the driver’s door lock/unlock switch (A) one more time to unlock all the doors. NOTE If the doors are unlocked when all doors are locked and no doors are opened within about 30 seconds, the doors will...
Page 118 OPEN switch (A) Mitsubishi Motors dealer for details. until the trunk lid opens. On a vehicle equipped with a Mitsubishi Multi-Communi- Also refer to “Trunk lid” on pages 3-59 respectively. cation System, the functions can be adjusted on the screen.
Page 119: Ignition Switch
Features and controls Ignition switch The engine runs and all electrical accessories can be used. N00513500059 To prevent vehicle theft, no F.A.S.T.-keys other than those reg- START istered in advance can be used to start the engine. (Electronic Engages the starter. Release the ignition switch when the immobilizer function) engine starts.
Page 120 Features and controls To turn from “LOCK (PUSH OFF)” to “ACC” To turn from “ACC” to “LOCK” N00513600021 N00513700051 Turn slowly after pressing the ignition switch. For vehicles with manual transaxle Slowly turn the ignition switch to the “LOCK” position while pressing it.
Page 121 Do not leave the ignition switch in the “ON” position If the following warning displays, contact an authorized for a long time when the engine is not running. Mitsubishi Motors dealer. Doing so could lead to a dead battery. Do not turn the ignition switch to the “START”...
Page 122 Features and controls If the following warning display, the display goes off if correc- A door cannot be locked even when the driver’s or front tive action is taken. passenger’s door lock/unlock switch is pressed. The ID codes of the F.A.S.T.-key and the vehicle cannot Type 1 be verified Type 1...
Page 123 This setting can be changed. unlock and a buzzer will sound for about 3 seconds. See an authorized Mitsubishi Motors dealer for details. The warning may display even if the F.A.S.T.-key is in the operating range for starting the engine. The surrounding environment or electromagnetic waves may make it impossible to verify the ID codes of the F.A.S.T.-key and...
Page 124 Features and controls Door ajar prevention system Ignition switch turn-off reminder system N00560000104 N00560100105 Type 1 Type 1 Type 2 Type 2 When the ignition switch is in the “LOCK (PUSH OFF)” posi- When the ignition switch is in a position other than “LOCK tion, and someone tries to lock the vehicle by pressing the (PUSH OFF)”, all the doors are closed, and someone tries to driver’s or front passenger’s door lock/unlock switch while one...
Page 125 Features and controls Steering wheel lock NOTE If the front wheels are turned, the anti-theft lock may N00514300025 sometimes make it difficult to turn the ignition switch from “LOCK” to “ACC” position. Firmly turn the steer- ing wheel to the left or to the right as you turn the ignition switch.
Page 126 Features and controls • If you shift the gearshift lever into the “N” (NEUTRAL) Starting the engine position and depress the accelerator pedal, increases in Your vehicle is equipped with an electronically controlled fuel the engine speed will be limited. injection system.
Page 127 Features and controls Startability of continuously variable transmission (CVT) 4. On vehicles with manual transaxle, place the gearshift vehicles or Twin Clutch SST vehicles at extremely cold lever in the “N” (Neutral) position. ambient temperature On vehicles with continuously variable transmission When the ambient temperature is -4°F (-20°C) or lower on (CVT) or Twin Clutch SST, make sure the selector lever vehicles with CVT, or -22°F (-30°C) or lower on vehicles with...
Page 128 Features and controls To operate using the emergency key NOTE Only use the emergency key in an emergency. When the N00514800020 battery of the F.A.S.T.-key has run down, replace the bat- Emergency key tery as soon as possible and use it as a F.A.S.T.-key again. N00515200148 After using the emergency key, be sure to reinsert it into The emergency key is built into the F.A.S.T.-key.
Page 129 Features and controls Ignition switch START Engages the starter. Release the emergency key when the N00529300179 To prevent vehicle theft, only the emergency key with the pre- engine starts. The ignition switch returns automatically to the registered F.A.S.T.-key inserted can start the engine. (Elec- “ON”...
Page 130 Features and controls To turn from “LOCK” to “ACC” 3. Insert the emergency key into the ignition switch, and slowly push and turn. 1. Remove the emergency key from the F.A.S.T.-key. Refer to “Emergency key” on page 3-33. 2. While pushing the lock release buttons (A), remove the cover of the ignition switch.
Page 131 Features and controls To turn from “ACC” to “LOCK” 2. Install the cover of the ignition switch. 3. Reinsert the emergency key into the F.A.S.T.-key. 1. [For vehicles with manual transaxle] Push the emergency key in at the “ACC” position and NOTE Always install the cover of the ignition switch when not keep it depressed until it is turned to the “LOCK”...
Page 132 Features and controls Steering wheel lock NOTE If the front wheels are turned, the anti-theft lock may sometimes make it difficult to turn the emergency key from “LOCK” to “ACC”. Firmly turn the steering wheel to the left or to the right as you turn the emergency key. Starting Tips for starting Do not operate the starter motor continuously for longer...
Page 133 Features and controls 1. Make sure all occupants are properly seated with seat WARNING belts fastened. Never run the engine in a closed or poorly ventilated 2. While pushing the lock release buttons (A), remove the area any longer than is needed to move your vehicle cover of the ignition switch.
Page 134 Features and controls 3. Insert the emergency key into the ignition switch. 5. Press and hold the brake pedal down with your right foot. 6. Press and hold the clutch pedal all the way down (manual transaxle). NOTE For models equipped with a manual transaxle, the starter will not operate unless the clutch pedal is fully depressed (Clutch interlock).
Page 135 Features and controls Startability of continuously variable transmission (CVT) 9. Turn the emergency key with the F.A.S.T.-key to the vehicles or Twin Clutch SST vehicles at extremely cold “START” position without pressing the accelerator pedal. ambient temperature Release the emergency key with the F.A.S.T.-key when When the ambient temperature is -4 °F (-20 °C) or lower on the engine starts.
Page 136 Features and controls Electronic immobilizer (Anti-theft starting sys- Registering the ID code can be done by your authorized Mitsubishi Motors dealer. Or it can be done by yourself (except tem) for vehicles sold in Canada). N00529600101 For you to register the ID code yourself, follow the “Customer The electronic immobilizer is designed to significantly reduce F.A.S.T.-key programming”...
Page 137 Features and controls 2. While pushing the lock release buttons (A), remove the 3. Insert the emergency key into the ignition switch. cover of the ignition switch. 4. Insert the first valid F.A.S.T.-key into the emergency key. I n f o r ma t i o n P r o v i d e d b y : 3-42...
Page 138 Features and controls NOTE 5. Turn the emergency key with the F.A.S.T.-key to the Perform the operation when the interrupt display screen is “ON” position for 5 seconds. not showing. The interrupt display screen may prevent 6. Turn the emergency key with the F.A.S.T.-key to the you from seeing the immobilizer display.
Page 139: Keyless Entry System
30 sec- onds. Refer to “Welcome light” on page 3-240. NOTE On a vehicle equipped with a Mitsubishi Multi-Communi- cation System, the functions can be adjusted on the 1- LOCK ( ) button screen.
Page 140 NOTE This is done with the key removed from the ignition switch. On a vehicle equipped with a Mitsubishi Multi-Communi- NOTE cation System, the functions can be adjusted on the The answerback function does not operate when the key is screen.
Page 141 NOTE Two chimes Driver’s door unlock only On a vehicle equipped with a Mitsubishi Multi-Communi- cation System, the functions can be adjusted on the 1. Turn the ignition switch to the “LOCK” position. If you screen. For details, refer to a separate operation manual.
Page 142 F.A.S.T.-keys. Registering the ID code can be done by your authorized Mitsubishi Motors dealer. Or it can be done by yourself (except for vehicles sold in Canada). For you to register the ID code yourself, follow the “Customer F.A.S.T.-key programming”...
Page 143 (already registered) F.A.S.T.-keys, blank (not regis- tered) F.A.S.T.-key and emergency key (specially cut for your vehicle at your Mitsubishi Motors dealer). To use the new F.A.S.T.-key, it is necessary to register the key with both the electronic immobilizer and keyless entry system.
Page 144 9. With the second valid F.A.S.T.-key, press the UNLOCK the doors will automatically re-lock. button for 4 to 10 seconds and press the LOCK button On a vehicle equipped with a Mitsubishi Multi-Communi- during this time. cation System, the functions can be adjusted on the 10.
Page 145 NOTE Be sure to perform the procedure with the Mitsubishi mark facing you. If the Mitsubishi mark is not facing you when you open the remote control transmitter case, the transmitter may come out.
Page 146: Door Locks
Never leave children unattended inside a vehicle. In appliance store. addition to the risk of heat stroke, children can acti- Your authorized Mitsubishi Motors dealer can replace the vate switches and controls, resulting in an injury or battery for you if you prefer.
Page 147 Features and controls To lock or unlock the front doors with the key NOTE When locking or unlocking with the key, only the driver’s Turn the key toward the front of the vehicle to lock the door. door will be locked or unlocked. After checking that the door is locked, turn the key back to the To lock or unlock all doors, use the power door lock center and remove it.
Page 148 Features and controls To lock or unlock the door from the inside To lock the door without using the key Move the lock knob to the lock position to lock the door. 1. Move the inside lock knob to the locked position. All doors should be kept locked while driving.
Page 149 Features and controls Key reminder system Ignition switch return reminder system N00549600178 N00503800121 When a key was used to start the engine When the F.A.S.T.-key was used to start the engine Type 1 Type 1 Type 2 Type 2 If the ignition switch is turned off and the driver’s door is If the driver’s door is opened while the ignition switch is in a opened with the key in the ignition switch, the key reminder position other than “LOCK”...
Page 150: Power Door Locks
Features and controls Power door locks To lock and unlock the doors N00509300564 Using the power door lock switch NOTE When locking or unlocking with the key on the driver’s door, only the driver’s door will lock or unlock. Repeated continuous operation between lock and unlock could activate the power door locking systems built-in protection circuit and prevent the system from operating.
Page 151 These functions are not activated when the vehicle is shipped from the factory. To activate or deactivate these functions, please contact your authorized Mitsubishi Motors dealer. Using the ignition switch position All doors will unlock when the ignition switch is turned to the “LOCK”...
Page 152 Features and controls NOTE Vehicles with CVT On a vehicle equipped with a Mitsubishi Multi-Communi- cation System, the functions can be adjusted on the screen. For details, refer to a separate operation manual. Vehicles with Twin Clutch SST I n f o r ma t i o n P r o v i d e d b y :...
Page 153: Child Safety Locks" For Rear Door
Features and controls “Child safety locks” for rear door WARNING N00509400190 Always keep the doors tightly closed and locked when driving. An unlocked door may be acciden- tally opened by a passenger, especially by a child who could fall out. Also, if the doors are not locked, there is a greater risk of someone being thrown from the vehicle in an accident.
Page 154: Trunk Lid
Features and controls Trunk lid To open N00509500175 Operation from outside the vehicle WARNING Using the key (Vehicles with key cylinder) Insert the key and turn it clockwise. It is dangerous to drive with the trunk lid open since The trunk lid will pop up slightly. Lift it to open the trunk. carbon monoxide (CO) gas can enter the cabin.
Page 155 Features and controls Operation from inside the vehicle The trunk area light remains illuminated for a certain period and then goes off automatically. Refer to “Interior light auto-cutout function (dome light and other lights)” on page 3-296. Pull the trunk lid release lever, located to the left of the driver’s seat, up to open the trunk.
Page 156 Features and controls To close NOTE Gas struts (A) are installed in the locations illustrated to Pull the trunk lid downward as illustrated. Gently slam the support the trunk lid. Please observe the following in trunk lid from the outside so that it is completely closed. order to prevent damage or faulty operation.
Page 157: Inside Emergency Trunk Lid Release
Features and controls Inside emergency trunk lid release You and your family should familiarize yourselves with the location and operation of the emergency trunk lid release lever. N00509800165 Children should be taught not to play in or around vehicles. The emergency trunk lid release is designed to provide a way to open the trunk lid from inside the trunk.
Page 158: Theft-Alarm System
Features and controls Theft-alarm system To open the trunk from the inside, move the lever (A) in the direction of the arrow on the lever. Push up on the trunk lid to N00510200185 open the trunk and climb out. The theft-alarm system is designed to provide protection from unauthorized entry into the vehicle.
Page 159 Features and controls At this time, the theft-alarm indicator (A) on the audio 3. Lock all doors by either the remote control transmitter or panel flashes for confirmation. the F.A.S.T.-key. Arm the system and leave 4. The system has entered the armed stage after about 20 seconds, when the theft-alarm indicator (A) flashing becomes slower.
Page 160 F.A.S.T.-key, the theft-alarm system may be malfunction- control transmitter or the F.A.S.T.-key. ing. The system will be disarmed if, while the theft-alarm indi- Have the vehicle inspected by an authorized Mitsubishi cator is illuminated, the ignition switch is turned to the Motors dealer. “ON” position.
Page 161 Features and controls Alarm stage Type of alarm When the alarm is activated: N00510400158 The alarm will be activated if any of the following occur while 1. The headlights blink on and off for 3 minutes. the vehicle is parked and the system is armed. After 3 minutes the headlights automatically shut off.
Page 162 Features and controls To deactivate the vehicle inclination detection function NOTE The alarm will continue to operate for 3 minutes. At the and the interior intrusion detection function (vehicles end of that period, the alarm will automatically shut off to equipped with the interior alarm sensor) save battery power.
Page 163 • If the ignition switch is turned to the “ON” or “ACC” relocks automatically can be adjusted. See an authorized position. Mitsubishi Motors dealer for details. On a vehicle equipped with a Mitsubishi Multi-Communication Sys- Disarmed stage tem, the functions can be adjusted on the screen. For N00510500133 details, refer to a separate operation manual.
Page 164: Power Windows
Features and controls Testing the theft-alarm system Power windows N00510600091 N00510800367 Use the following procedure to test the system: 1. Lower the driver’s window. 2. Arm the system as explained in “Armed stage”. 3. Make sure that the theft-alarm indicator comes on and flashes for approximately 20 seconds.
Page 165: Main Switch
Features and controls WARNING Before operating the power windows, make sure that nothing can be trapped (head, hands, fingers, etc.) in the window. Never leave the vehicle with the key in the ignition switch. Never leave a child alone in the vehicle. Main switch The main switch located on the driver’s door can be used to operate all door windows.
Page 166 Features and controls Sub switch Timer function The power windows can be run up or down when the ignition switch is in the “ON” position. The door windows can be opened or closed for a 30 second period after the ignition switch is turned to the “ACC” or “LOCK”...
Page 167 Features and controls Safety mechanism (Driver’s door window only) NOTE The safety mechanism can be activated if the driving con- N00528800092 If a hand or head is trapped, for safety the door window is auto- ditions or other circumstances cause the door window to matically lowered a little.
Page 168 Features and controls Lock switch What to do if you hear wind buffeting when driv- N00549000127 When this switch is in the lock mode, the main switch for pas- N00551400014 senger door window and the sub switch cannot be used to open Wind buffeting can be described as the perception of pressure or close the door window, and the main switch will open or on the ears or a booming or rumbling sound.
Page 169 Features and controls Sunroof To open (if so equipped) Press the switch (1), the sunroof automatically opens and the N00511000656 sunroof will stop several centimeters this side of the full open WARNING position. Press the switch (1) again, and the sunroof will be fully open.
Page 170 (2). After performing the emergency measure, consult an autho- rized Mitsubishi Motors dealer. NOTE The safety mechanism can be activated if the driving con- ditions or other circumstances cause the sunroof to be sub- jected to a physical shock similar to that caused by a trapped hand or head.
Page 171 If nothing is trapped, have the sunroof checked at an authorized Mitsubishi Motors dealer. Be careful when tilting up the sunroof if a ski carrier or a roof carrier is installed.
Page 172: Parking Brake
Features and controls Parking brake To apply N00511400298 To park the vehicle, first bring it to a complete stop, fully engage the parking brake, and then move the gearshift lever to 1st (on a uphill) or “R” (Reverse) (on a downhill) position, for vehicles with a manual transaxle, set the selector lever {contin- uously variable transmission (CVT)} or the gearshift lever (Twin Clutch SST) to “P”...
Page 173 Features and controls To release CAUTION Before driving, be sure that the parking brake is fully released and brake warning light is off. If you drive without the parking brake fully released, the warning display will appear on the information screen in the multi-information display. If a vehicle is driven without releasing the parking brake, the brakes will be overheated, resulting in ineffective braking and possible brake failure.
Page 174: Steering Wheel Tilt Lock Lever
Features and controls Steering wheel tilt lock lever WARNING N00511500215 To adjust the steering wheel height, release the tilt lock lever After adjusting, make sure the lock lever is secured in the locked (1) position. while holding the steering wheel by hand, and raise or lower Do not attempt to adjust the steering wheel while the steering wheel to the desired height.
Page 175: Inside Day/Night Rearview Mirror
Features and controls Inside day/night rearview mirror Type 1 N00548600067 Adjust the inside rearview mirror only after making any seat adjustments so as to have a clear view to the rear of the vehicle. WARNING Do not attempt to adjust the inside rearview mirror while driving.
Page 176 Features and controls To adjust the mirror position Adjust the inside mirror to maximize the view through the rear window. It is possible to move the mirror up/down and left/right to adjust its position. To adjust the vertical mirror position It is possible to move the mirror up and down to adjust its posi- tion.
Page 177 Features and controls To reduce the glare Type 2 When the headlights of the vehicles behind you are very bright, Type 1 the reflection factor of the rearview mirror is automatically The day/night knob (A) at the bottom of the mirror can be used changed to reduce the glare.
Page 178: Outside Rearview Mirrors
Features and controls Outside rearview mirrors Type 3 When the headlights of the vehicles behind you are very bright, N00512200192 the reflection factor of the rearview mirror is automatically Adjust the outside rearview mirrors only after making any seat changed to reduce the glare. adjustments so you have a clear view to the rear of the vehicle.
Page 179 Features and controls To adjust the mirror position To fold the mirror The outside rearview mirrors can be adjusted when the ignition The outside mirror can be folded in toward the side window to switch is in the “ON” or “ACC” position. prevent damage when parking in tight locations.
Page 180 Features and controls Heated mirror Ignition switch (if so equipped) N00549300175 N00512400615 When the rear window defogger switch is pressed with the [For vehicles equipped with the F.A.S.T.-key] engine running, the outside rearview mirrors are defogged or For information on operations for vehicles equipped with the defrosted.
Page 181 • The time until the power cuts out can be changed to about 60 minutes. • The ACC power auto-cutout function can be deacti- vated. For details, consult a Mitsubishi Motors dealer. On vehicles equipped with Mitsubishi Multi-Communica- tion System, screen operations can be used to make the adjustment.
Page 182 Features and controls To remove the key For vehicles with a continuously variable transmission (CVT) or Twin Clutch SST, when removing the key, first set the selec- N00550900184 For vehicles with a manual transaxle, when removing the key, tor lever (CVT) or the gearshift lever (Twin Clutch SST) to the push the key in at the “ACC”...
Page 183: Steering Wheel Lock
Features and controls Steering wheel lock CAUTION N00512500195 Do not remove the ignition key from the ignition [For vehicles equipped with the F.A.S.T.-key] switch while driving. The steering wheel will lock, For information on operations for vehicles equipped with the causing loss of control.
Page 184: Starting And Stopping The Engine
Features and controls To lock Starting and stopping the engine Remove the key at the “LOCK” position. N00542100060 Turn the steering wheel until it is locked. Tips for starting To unlock Do not operate the starter motor continuously for longer than 15 seconds as this could run the battery down or Turn the key to the “ACC”...
Page 185 Features and controls Starting the engine • If you shift the gearshift lever into the “N” (NEUTRAL) position and depress the accelerator pedal, increases in N00542200104 [For vehicles equipped with the F.A.S.T.-key.] the engine speed will be limited. For information on operations for vehicles equipped with the WARNING F.A.S.T.-key, refer to “F.A.S.T.-key: Starting the engine”...
Page 186 Features and controls Startability of continuously variable transmission 6. On vehicles with manual transaxle, place the gearshift (CVT) vehicles or Twin Clutch SST vehicles at lever in the “N” (Neutral) position. On vehicles with continuously variable transmission extremely cold ambient temperature (CVT) or Twin Clutch SST, make sure the selector lever When the ambient temperature is -4 °F (-20 °C) or lower on (CVT) or gearshift lever (Twin Clutch SST) is in the “P”...
Page 187 Features and controls Stopping the engine NOTE For vehicles with Twin Clutch SST, the engine will stop N00542300088 1. Bring the vehicle to a complete stop. and the vehicle power will turn off approximately 1 sec- ond after the ignition switch is turned to the “LOCK”; 2.
Page 188: Turbocharger Operation (If So Equipped)
Features and controls Turbocharger operation For vehicles with Twin Clutch SST, if the temperature (if so equipped) inside the engine compartment is high, the cooling fans N00537300051 (A) will continue to operate for some time even if the CAUTION engine is stopped. Therefore, the operation sound of the cooling fans may be Do not run the engine at high speeds (for example, heard even after the engine is stopped.
Page 189: Manual Transaxle (If So Equipped)
Features and controls Turbocharger Manual transaxle (if so equipped) The turbocharger increases engine power by pushing large N00512700113 The shift pattern below is shown on the gearshift lever. Press amounts of air into the engine’s cylinders. The finned parts the clutch pedal all the way down while shifting gears. inside the turbocharger turn at extremely high speeds and are subjected to extremely high temperatures.
Page 190 Features and controls To start Proper shift points Press the clutch pedal all the way down and shift into 1st or N00537400049 Always use care to change the gear with the vehicle speed “R” (Reverse) position. Then gradually release the clutch pedal matched to the engine speed.
Page 191 Features and controls Changing gears while the vehicle is moving Upshifting N00548100017 N00512900131 Always use care to change the gear with the vehicle speed For the best fuel economy and performance in using your man- matched to the engine speed. Proper shifting will improve fuel ual transaxle, upshift as listed below.
Page 192: Driving Precautions
Features and controls Downshifting Driving precautions N00513000096 N00513100215 It is recommended that you downshift to a lower gear when The table below shows the maximum recommended driving needed to maintain the desired speed, according to the table. speed for in each gear. Do not drive near or at these speeds for Avoid downshifting at too high a speed.
Page 193: Driving Downhill
Features and controls Continuously variable transmission (CVT) Selector lever operation (if so equipped) N00513800384 As an additional safety precaution, models equipped with a N00513200186 continuously variable transmission have a shift-lock device The CVT is capable of changing the engine speed to vehicle that holds the selector lever in the “P”...
Page 194 Features and controls Except for vehicles with manual gate The CVT has 2 forward selector positions and 1 reverse selec- tor position. The CVT selects an optimum ratio automatically when the selector lever is in the “D” (DRIVE) or “L” (LOW) position, depending on the speed of the vehicle and the position of the accelerator pedal.
Page 195 Features and controls Vehicles with manual gate NOTE To ensure proper transmission operation, stop at each The CVT has 2 forward selector positions and 1 reverse selec- detent position when shifting. After shifting, check the tor position. position in the multi-information display. The CVT selects an optimum ratio automatically when the If the brake pedal is not depressed and held, the shift-lock selector lever is in the “D”...
Page 196 Features and controls NOTE To ensure proper transmission operation, stop at each detent position when shifting. After shifting, check the position in the multi-information display. If the brake pedal is not depressed and held, the shift-lock device activates to prevent the selector lever from being moved from the “P”...
Page 197 Immediately have your vehicle checked by an authorized 6. Insert a screwdriver in the shift-lock release hole (B). Mitsubishi Motors dealer or a repair facility of your choice. Shift the selector lever to the “N” (NEUTRAL) position If you need to move the vehicle, shift the selector lever as fol- while pressing the screwdriver down.
Page 198: Warning Display
Features and controls Selector lever position display Warning display N00513900402 N00514000194 When the ignition switch is turned to the “ON” position, the Type 1 selector lever position is shown on the multi-information dis- play. Type 2 When the warning display or the warning display appears on the information screen in the multi-information dis- play while you are driving, there could be a malfunction in the...
Page 199 CVT, causing a safety device to activate. Have will appear on the information screen in the multi- your vehicle inspected by an authorized Mitsubishi information display. Motors dealer or a repair facility of your choice as In this case, immediately park your vehicle in a safe soon as possible.
Page 200 Features and controls “N” NEUTRAL “D” DRIVE At this position, the transmission is disengaged. It is the same This position is used for most city and highway driving. Engine as the neutral position on a manual transaxle and should be shifting and braking are done automatically as needed, depend- used when the vehicle is not moving for an extended length of ing on road conditions.
Page 201 Features and controls Sports mode (if so equipped) SHIFT UP N00514400417 Vehicles with manual gate SHIFT Whether the vehicle is stationary or in motion, sports mode is DOWN selected by pushing the selector lever from the “D” (DRIVE) position into the manual gate (1). To return to “D” (DRIVE) operation, push the selector lever back into the main gate (2).
Page 202 Features and controls Except for vehicles with manual gate CAUTION While driving with the selector lever in the “D” (DRIVE), By rapidly moving the selector lever or sportronic sports mode can be selected by pulling one of the sportronic steering wheel paddle shifter to the “- (SHIFT steering wheel shifters toward you.
Page 203 Features and controls CAUTION By rapidly moving the sportronic steering wheel paddle shifter to the “- (SHIFT DOWN)” side twice, it is possible to skip one shift range (i.e., 3rd to 1st or 4th to 2nd). Since sudden engine braking or acceler- SHIFT DOWN ation can cause a loss of traction, downshifts must be made carefully in accordance with the vehicle’s...
Page 204 Features and controls Operation of the CVT Sports mode display N00538800154 N00514500287 In sports mode, the currently selected shift range is displayed CAUTION on the information screen in the multi-information display. Before selecting a position with the engine running and the vehicle stationary, fully depress the brake pedal to prevent the vehicle from creeping.
Page 205 Features and controls Passing acceleration CAUTION N00514900063 To gain extra acceleration in “D” (DRIVE) position (when Do not rev the engine with the brake pedal pressed passing another vehicle) push the accelerator to the floor if it is when the vehicle is stationary. safe to do so in traffic conditions.
Page 206 If you are going to leave the vehicle unattended, always switch causing a safety device to activate. Have your vehicle checked off the engine and carry the key. at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. NOTE 1.
Page 207: Gearshift Lever Operation
Features and controls Twin Clutch SST (Sportronic Shift Trans- Gearshift lever operation mission) N00539800050 (if so equipped) As an additional safety precaution, models equipped with a Twin Clutch SST have a shift-lock device that holds the gear- N00539700059 The Twin Clutch SST is a transmission that, through integrated shift lever in the “P”...
Page 208 Features and controls The Twin Clutch SST has 6 forward gears and 1 reverse gear. The individual gears are selected automatically, depending on the position of the gearshift lever, the speed of the vehicle and the position of the accelerator pedal. The gearshift lever (A) has 2 gates;...
Page 209: Gearshift Lever Position Display
Features and controls Gearshift lever position display WARNING N00539900064 When the ignition switch is turned to the “ON” position, the If the pull-ring is always pulled up when using the gearshift lever position is shown on the multi-information dis- gearshift lever, the gearshift lever may be acciden- play.
Page 210 Features and controls In addition, when the vehicle is driven with the gearshift lever When the gearshift lever position display blinks in the “D” (DRIVE) position, the forward gear number is When the gearshift lever is placed in the “R” (REVERSE) shown.
Page 211 N00540000052 function. If the gearshift lever position display is not shown and the vehicle cannot move, or if this problem occurs repeatedly, have the vehicle checked by an authorized Mitsubishi Motors dealer When the warning display or the warning display or a repair facility of your choice as soon as possible.
Page 212 If the display goes out, the vehicle can be driven normally. driven normally. If the warning display remains on or comes on frequently, have the vehicle checked by an authorized Mitsubishi Motors dealer If vehicle is driven with warning displayed or a repair facility of your choice.
Page 213 If the warning display remains on or comes on frequently, have This position locks the transmission to prevent the vehicle the vehicle checked by an authorized Mitsubishi Motors dealer from moving. The engine can be started from the “PARK” or a repair facility of your choice.
Page 214 Features and controls “N” NEUTRAL “D” DRIVE At this position, the transmission is disengaged. It is the same This position is used for most city and highway driving. Engine as the neutral position on a manual transaxle and should be shifting and braking are done automatically as needed, depend- used when the vehicle is not moving for an extended length of ing on road conditions.
Page 215 Features and controls Twin Clutch SST control mode NOTE When continuously driving on closed circuit tracks or at N00540200070 Select the control mode from the following two types to suit other locations where the engine is operated at high the driving conditions. speeds and under a heavy load, the Twin Clutch SST fluid temperature will have a tendency to rise.
Page 216 Features and controls Twin Clutch SST control mode switch To shift from “Normal” mode to “Sport” mode While the vehicle is stopped or being driven, push the Twin N00540300068 When the ignition switch is set to the “ON” position, operate Clutch SST control mode switch forward.
Page 217: Manual Shift
Features and controls Manual shift Twin Clutch SST control mode display N00540400043 N00540500031 When the ignition switch is set to the “ON” position, the cur- Using the gearshift lever (A) or the sportronic steering wheel rently selected control mode is displayed on the multi-informa- shifters (B), shifting can be performed manually.
Page 218 Features and controls NOTE CAUTION Only the forward gears 1 to 6 can be selected. When manually shifting while the vehicle is being To reverse or park, place the gearshift lever in the “R” driven, select the correct shift position to control the (REVERSE) or “P”...
Page 219 Features and controls Shifting using the gearshift lever Shifting up and shifting down Each time the gearshift lever is pulled rearward, the transmis- N00540600032 sion shifts up 1 gear. Selecting manual shifting In addition, each time the gearshift lever is pushed forward, the While the vehicle is stopped or being driven, move the gear- transmission shifts down 1 gear.
Page 220 Features and controls Returning to “D” range operation Shifting using the sportronic steering wheel shifters Move the gearshift lever toward the front passenger’s seat to N00540700033 return to automated shifting. Selecting manual shifting While the vehicle is stopped or being driven with the gearshift lever in the “D”...
Page 221 Features and controls Shifting up Shifting down Each time the + (SHIFT UP) sportronic steering wheel shifter Each time the - (SHIFT DOWN) sportronic steering wheel is pulled, the transmission shifts up 1 gear. shifter is pulled, the transmission shifts down 1 gear. NOTE After manual shifting is selected using the sportronic steering wheel shifters, shifting up and down can also be...
Page 222 Features and controls Returning to “D” range operation NOTE When the gearshift lever is in the “D” (DRIVE) position, pull If manual shifting is selected using the sportronic steering the + (SHIFT UP) sportronic steering wheel shifter toward you wheel shifters when the gearshift lever is in the “D” for 2 seconds or more to return to “D”...
Page 223 Features and controls Operation of the Twin Clutch SST Manual shift display N00543000040 N00540800021 In manual shift, the currently selected gear is displayed on the CAUTION multi-information display. Before selecting a position with the engine running and the vehicle stationary, fully depress the brake pedal to prevent the vehicle from creeping.
Page 224 Features and controls Passing acceleration CAUTION N00540900019 To gain extra acceleration in “D” (DRIVE) position (when Do not rev the engine with the brake pedal pressed passing another vehicle) push the accelerator to the floor if it is when the vehicle is stationary. safe to do so in traffic conditions.
Page 225 Features and controls Waiting CAUTION N00541000033 For short waiting periods, such as at traffic lights, the vehicle Do not use the tendency of the vehicle to creep for- can be left in gearshift lever position and held stationary with ward in order to drive at low speeds up hills. the service brake.
Page 226 Features and controls Parking CAUTION N00541100018 To park the vehicle, first bring it to a complete stop, fully Do not keep the vehicle in a stopped position on an engage the parking brake, and then move the gearshift lever to uphill slope by depressing the accelerator pedal the “P”...
Page 227 Mitsubishi Motors dealer or a repair facility amount of wear for all four wheels. Otherwise, the of your choice as soon as possible.
Page 228 Features and controls ACD control mode ACD control mode switch When the ignition switch is set to the “ON” position, operate N00545400048 Select the control mode from the following three types to suit the AWC switch to change the control mode. the driving conditions.
Page 229: Acd Warning Display
Features and controls ACD control mode display In addition, the ACD control mode display in section (A) will go out at the same time. Example: “TARMAC” mode is selected. The currently selected control mode is displayed on the multi- information display. In addition, when the control mode is changed, the selected mode appears on the interrupt display screen of the information screen in the multi-information display.
Page 230 Features and controls Electronically controlled 4WD system NOTE (if so If the ambient temperature drops and the viscosity of the equipped) AWC control fluid increases, the warning may be dis- N00548300019 played. The electronically controlled 4WD system is an all-wheel drive At this time, ACD control is temporarily suspended, but system that allows one of three drive modes to be selected with this will not affect normal driving.
Page 231: Drive Mode-Selector
Features and controls Drive mode-selector Display N00548400010 Drive mode The drive mode can be selected by pressing the switch while Type 1 Type 2 the ignition switch is in the “ON” position. 4WD AUTO 4WD LOCK CAUTION Do not operate the drive mode-selector with the front wheels spinning on a snowy road or in similar conditions.
Page 232: Drive Mode Indicator
5 min- Drive mode indicator utes, have the vehicle inspected at an authorized Drive mode Mitsubishi Motors dealer or a repair facility of your “4WD” indicator “LOCK” indicator choice as soon as possible.
Page 233 Have an the protection of the drive-system components, caus- inspection made by an authorized Mitsubishi ing the drive mode in “4WD AUTO” mode to lock or Motors dealer or a repair facility of your choice as the “4WD”...
Page 234: All-Wheel Driving Operation
Features and controls All-wheel driving operation Turning sharp corners When turning a sharp corner in “4WD LOCK” position at low N00530600169 speed, a slight difference in steering may be experienced simi- For vehicles with full-time 4WD lar to feeling as if the brakes were applied. This is called tight Full-time 4WD vehicles are propelled by engine power distrib- corner braking and results from each of the four tires being at a uted constantly and appropriately to all 4 wheels.
Page 235 Features and controls Moving out of mud NOTE Avoid sudden braking, sudden acceleration and sharp Set the drive mode-selector to “4WD LOCK” and then gradu- ally depress the accelerator pedal for a smooth start. turning; such operations could result in the vehicle becoming stuck.
Page 236 Features and controls Cautions on handling of all-wheel drive CAUTION vehicles Always use tires of the same size, same type, and N00530800190 same brand, and which have no wear differences. Tires and wheels Using tires that differ in size, type, brands or the degree of wear, will increase the differential oil tem- Since driving torque can be applied to all four wheels, the per- perature, resulting in possible damage to the driving...
Page 237 Features and controls Towing CAUTION [For vehicle equipped with the Electronically con- trolled 4WD system] Even in “2WD” mode, the vehicle cannot be towed with the front or the rear wheels on the ground. Jacking up a all-wheel drive vehicles WARNING Do not start or run the engine while the vehicle is on the jack.
Page 238: Limited-Slip Differential (If So Equipped)
Features and controls Limited-slip differential Service brake (if so equipped) N00517400069 N00517500262 A limited-slip differential is applied for rear wheel differential. Brake pedal The features of this limited-slip differential are described Overuse of the brake can cause poor brake response and pre- below: mature wear of the brake pads and linings.
Page 239: Power Brakes
If you hear this sound, have the brake pads replaced at an Your brakes are designed to operate at full capacity, even if the authorized Mitsubishi Motors dealer or a repair facility of your power assist is lost. choice.
Page 240 Features and controls Brake assist system NOTE Once the brake assist system is operational, it maintains N00567300018 The brake assist system is a device assisting drivers who can- great braking force even if the brake pedal is lightly released. not depress the brake pedal firmly such as in emergency stop To stop its operation, completely remove your foot from situations and provides greater braking force.
Page 241 Features and controls Hill start assist (vehicles with Twin Clutch To operate SST) N00562700062 1. Stop the vehicle completely using the brake pedal. N00562600032 2. Release the brake pedal and the hill start assist will main- The hill start assist makes it easy to start off on a steep uphill tain the braking force applied while stopping for approxi- slope by preventing the vehicle from moving backwards.
Page 242: Anti-Lock Braking System
In this situation, simply hold the brake pedal down the vehicle should be inspected by an authorized firmly. Do not pump the brake, which will result in Mitsubishi Motors dealer or a repair facility of your reduced braking performance. choice as soon as possible.
Page 243 Never install a limited slip differential as the ABS may not function normally. Please consult an authorized Mitsubishi Motors dealer. Warning display type 2 NOTE...
Page 244 • The warning display appears while driving the vehicle checked by an authorized Mitsubishi Motors dealer or repair facility of your choice as soon as possible. I n f o r ma t i o n P r o v i d e d b y :...
Page 245 Avoid hard braking and high-speed driving. Stop the vehicle in a safe place and contact an authorized Mitsubishi Motors dealer or repair facility of your choice. NOTE The anti-lock braking system warning light and brake...
Page 246 Features and controls Active Stability Control (ASC) (if so equipped) Rear N00559100118 The Active Stability Control (ASC) takes overall control of the anti-lock braking system, traction control function and skid control function to help maintain the vehicle’s control and trac- tion.
Page 247 Features and controls Skid control function NOTE An operation noise may be emitted from the engine com- N00559300035 The skid control function is designed to help the driver main- partment in the following situations. The sound is associ- tain control of the vehicle on slippery roads or during rapid ated with checking the operations of the ASC.
Page 248 Features and controls “ASC OFF” switch NOTE Using the “ASC OFF” switch turns off both the skid con- N00559400179 trol function and the traction control function. The ASC is automatically activated when the ignition switch is When moving out of mud, sand or fresh snow, pressing turned to the “ON”...
Page 249 Features and controls ASC operation display or ASC OFF display CAUTION N00559500183 When display/indicator blinks, ASC is operating, ASC operation display/ASC indicator which means that the road is slippery or that your The display/indicator will blink when the ASC is operat- vehicle’s wheels are beginning to slip.
Page 250 Warning display type 1 cle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible.
Page 251: Power Steering System
“free play” in the steering steering system. wheel. If this happens, take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice. Electric power steering system (EPS) (if so...
Page 252: Cruise Control (If So Equipped)
Mitsubishi Motors dealer or a repair facility of your I n f o r ma t i o n P r o v i d e d b y : choice.
Page 253 Features and controls Your speed may increase to more than the set speed on a C- “ACC RES” switch steep downhill. You must use the brake to control your To increase the set speed and to resume to the previous set speed.
Page 254: Cruise Control Indicator
Features and controls Cruise control indicator To activate N00550100245 N00518400343 This indicator will come on when the cruise control “ON OFF” 1. Lightly press the “ON OFF” switch (A). switch (A) is pressed to turn on the cruise control system. Type 1 Type 2 I n f o r ma t i o n P r o v i d e d b y :...
Page 255 Features and controls NOTE 3. Accelerate or decelerate to your desired speed, then press If the cruise control is on when the ignition switch is and release the “COAST SET” switch (B) when the turned to “OFF” position, cruise control will turn on auto- “CRUISE”...
Page 256 Features and controls To increase the set speed press the “ACC RES” switch (C), the speed will increase by approximately 1 mph (1.6 km/h). N00518500331 There are 2 ways to increase the set speed. Accelerator pedal “ACC RES” switch Use the accelerator pedal to reach your desired speed. Press the If you press and hold down the “ACC RES”...
Page 257 Features and controls To decrease the set speed time you press the “COAST SET” switch (B), the speed will decrease by approximately 1 mph (1.6 km/h). N00518600260 There are 2 ways to reduce the set speed. Brake pedal “COAST SET” switch Press the brake pedal (which disengages the cruise control) and Press and hold the “COAST SET”...
Page 258 Features and controls To temporarily increase or decrease the speed To temporarily decrease the speed Apply the brakes to decrease the speed. To return to the previ- N00518700128 ously set speed, press the “ACC RES” switch (C). Refer to “To To temporarily increase the speed resume the set speed”...
Page 259 Features and controls To deactivate When you depress the clutch pedal (on vehicles with man- ual transaxle). N00518800493 The cruise control can be turned off as follows: Your speed slows to about 10 mph (15 km/h) or more Press the “ON OFF” switch (A). (Cruise control will be below the set speed because of an uphill, etc.
Page 260 Press the “ON OFF” switch to turn off the cruise control and have your vehicle inspected by an autho- rized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 261: Tire Pressure Monitoring System
When the spare tire is used, the tire pressure moni- toring system will not work properly. See an authorized Mitsubishi Motors dealer as soon as possible to replace or repair the original tire. I n f o r ma t i o n P r o v i d e d b y :...
Page 262 When the ignition switch is turned to the “ON” position, the ones when the tire is replaced. tire pressure monitoring system warning light normally illumi- For details, contact your authorized Mitsubishi Motors nates and goes off a few seconds later. dealer.
Page 263 However, if the warning light does not go off, or if it blinks again when the engine is restarted, have the vehicle inspected by an authorized Mitsubishi Motors dealer. In such situations, a malfunctioning of the system may be preventing the monitoring of the tire pres- sure.
Page 264 Features and controls Each tire, including the spare (if provided), should be checked When the malfunction indicator is illuminated, the system may monthly when cold and inflated to the inflation pressure rec- not be able to detect or signal low tire pressure as intended. ommended by the vehicle manufacturer on the vehicle placard TPMS malfunctions may occur for a variety of reasons, includ- or tire inflation pressure label.
Page 265 Do not use metal valve caps, which may cause a metal Mitsubishi Motors dealer. If the tire repair is not done by reaction, resulting in corrosion and damage of the tire an authorized Mitsubishi Motors dealer, it is not covered inflation pressure sensors.
Page 266 Have tire and wheel replacement per- The tire inflation pressure sensor’s battery is dead. formed by an authorized Mitsubishi Motors dealer to avoid the Wheels other than Mitsubishi genuine wheels are being risk of damaging the tire inflation pressure sensors. If the used.
Page 267: Rear-View Camera (If So Equipped)
Rules (For vehicles sold in Canada). This device complies with the Mitsubishi Multi-Communication System in the center Part 15 of the FCC Rules and RSS-Gen of the Industry Canada panel or on the left portion of the inside rearview mirror.
Page 268 Features and controls Location of rear-view camera Reference lines on the screen The rear-view camera (A) is built-in to the trunk lid. Reference lines and upper surface of the rear bumper (A) are displayed on the screen. Red line (B) indicates approximately 20 inches (50 cm) behind the rear bumper.
Page 269 Features and controls CAUTION Case 1 The rear-view camera uses a wide-angle lens. As a result, images and distances shown on the screen are not exact. Actual distance may be different from distance indi- cated by the lines on the screen, depending on the loading condition of the vehicle and road surface condition.
Page 270 They may not indi- For details, please refer to the separate owner’s manual for cate correct distance depending on the shape of an “Mitsubishi Multi-Communication System” or “Change obstacle. language or turn off the inside rearview mirror screen : To For example, when there is an object behind the change the language of warning text (3)”...
Page 271 Features and controls Change language or turn off the inside rearview To permanently set the non-display mode mirror screen 1. Turn the ignition switch to the “ON” position. N00568900040 It is possible to turn off the screen of the inside rearview mirror CAUTION and change the language of the warning messages on the For safety reasons, do not perform the following...
Page 272 Features and controls To change the language of warning text (3) N00548200018 1. Turn the ignition switch to the “ON” position. CAUTION For safety reasons, do not perform the following operations with the engine running. 2. Put the gearshift lever or the selector lever in the “R” (REVERSE) position.
Page 273: Instrument Cluster
Features and controls Instrument cluster Speedometer N00519100190 N00519000333 The speedometer shows the vehicle speed in miles per hour (mph) or kilometers per hour (km/h). Type 1 Tachometer → P.3-179 Multi-information display → P.3-181 Information screen display list → P.3-216 Speedometer → P.3-178 Rheostat meter illumination button →...
Page 274 Features and controls Tachometer Type 2 N00519200276 The tachometer shows engine revolutions per minute. This allows the driver to determine the most efficient shift position (manual transaxle), selector position {continuously variable transmission (CVT)} or shift position (Twin Clutch SST) and engine speed combinations.
Page 275 Features and controls Rheostat meter illumination button N00554900137 Each time you press this button, there is a sound and the bright- ness of the instruments changes. NOTE You can adjust to 8 different levels respectively for when the tail lights are illuminated and when they are not. If the vehicle is equipped with the automatic light control, when the light switch is in a position other than the “OFF”...
Page 276: Multi-Information Display
Features and controls Multi-information display N00555000236 The multi-information display displays warnings, the odometer, trip odometer, service reminder, engine coolant temperature, fuel remaining, outside temperature, Twin Clutch SST control mode, ACD control mode, gearshift lever position, selector lever posi- tion, all-wheel drive operation status, average and momentary fuel consumption, driving range, average speed, instrument bright- ness, etc.
Page 277 Features and controls Multi-information meter switch 9- Engine coolant temperature display (if so equipped) → P.3- N00555100136 The multi-information meter switch is a button marked 10- Twin Clutch SST control mode display screen (Twin Clutch “INFO” on the left side of the dash. SST) →...
Page 278 Features and controls Warning display screen (With ignition switch Type 1 in the “OFF” position) N00555200137 If you press the multi-information meter switch and return from the warning display screen to the previous screen, the When there is no warning is displayed. warning display Refer to “Returning to the display screen from before the warn- ing display”...
Page 279 Features and controls 1- Odometer (Type 1), Trip odometer 2- Odometer (Type 1), Trip odometer 3- Service reminder 4- Redisplay of a warning display screen Type 1 Odometer/Trip odometer N00555400100 Each time you lightly press the multi-information meter switch, the display screen changes as follows: →...
Page 280 Features and controls Interrupt display screen (With ignition switch in NOTE If there is no warning display, the switching sequence is: the “OFF” position) → Odometer/Trip odometer Odometer/Trip odometer N00559600155 When there is information to be announced, such as a key →...
Page 281 Features and controls Returning to the display screen from before the warn- NOTE ing display Warning display screens with a “ ” or “ ” mark dis- Even if the cause of the warning display is not eliminated, you played in the upper right of the screen can be switched. If can return to the screen that was displayed before the warning you want to switch the display, press the multi-informa- display.
Page 282 Features and controls Door ajar warning display (With ignition switch Information screen (With ignition switch turned in the “OFF” position) from “OFF” to “ON” position) N00559700130 N00555800133 If any of the doors or the trunk lid is not completely closed, the When the ignition switch is turned to the “ON”...
Page 283 Features and controls System check screen Service reminder When the ignition switch is turned to the “ON” position, the When the time for periodic inspection arrives, the warning dis- system check screen is displayed for about 4 seconds. If there play is displayed for a few seconds after the screen that is ini- is no fault, information screen (when the ignition switch is tially displayed when the ignition switch is turned “ON”.
Page 284 Features and controls “Active stability control (ASC) OFF” display Warning display screen (With ignition switch screen in the “ON” position) (if so equipped) N00556100074 N00555200140 This is displayed when the Active stability control (ASC) is This is displayed when you press the multi-information meter turned “OFF”...
Page 285 Features and controls Type 1 1- Odometer (Type 1)/Trip odometer 2- Odometer (Type 1)/Trip odometer 3- Service reminder 4- Engine coolant temperature display (Type 1) 5- Driving range display (Type 1) 6- Average speed display, average fuel consumption display, When there is no warning display momentary fuel consumption display (Type 1) 7- Driving range display, momentary fuel consumption display (Type 2)
Page 286 Features and controls Odometer/Trip odometer Driving range display The operation method is the same as when the ignition switch Shows the approximate driving range (how many more miles is in the “OFF” position. or kilometers you can drive) with the current fuel level. When For further details, refer to “Odometer/Trip odometer”...
Page 287 Features and controls Average speed display The initial (default) setting is “Auto reset mode”. The display setting can be changed to the preferred units This displays the average speed from the last reset to the (mph or km/h). present. Refer to “Changing the function settings (With ignition There are 2 types of mode settings as follows.
Page 288 Features and controls Auto reset mode Momentary fuel consumption display When the average fuel consumption is being displayed, if While driving, the momentary fuel consumption is shown with you hold down the multi-information meter switch, these a bar graph. calculations will be reset to zero. When the momentary fuel consumption surpasses the average When the ignition switch has been set to the “ACC”...
Page 289 Features and controls Interrupt display screen (With ignition switch in Type 1 the “ON” position) N00556300135 Warning display When there is information to be announced, such as a system fault, a tone sounds and the information screen is switched to the warning display screen.
Page 290 Features and controls Redisplay of a warning display screen NOTE Warning display screens with a “ ” or “ ” mark dis- When the warning is displayed, if you lightly press the played in the upper right of the screen can be switched. If multi-information meter switch a few times, the warning dis- you want to switch the display, press the multi-informa- play screen you switched from is redisplayed.
Page 291 Features and controls Outside temperature display screen Fuel remaining display screen N00556500094 N00556600125 Shows the temperature outside the vehicle. Shows the amount of fuel remaining. NOTE Type 1 Type 2 The display setting can be changed to the preferred units (°F or °C).
Page 292 Features and controls Fuel tank filler door mark NOTE On hills or curves, the display may be incorrect due to the The arrow (A) indicates that the fuel tank filler door is located on the left side of the vehicle. (Refer to “Filling the fuel tank” movement of fuel in the tank.
Page 293: Service Reminder
Type 1 Type 2 Type 2 3. After your vehicle is inspected at an authorized Mitsubishi Motors dealer, it displays the time until the next periodic inspection. I n f o r ma t i o n P r o v i d e d b y :...
Page 294 Features and controls To reset 2. Press and hold the multi-information meter switch (for The “---” display can be reset while the ignition switch is in the about 2 seconds or more) to display “ ” and make it “OFF” position. When the display is reset, the time until the flash.
Page 295 If you accidentally reset the display, consult an authorized Type 2 Mitsubishi Motors dealer for assistance. CAUTION Always make sure that the warning display goes out before beginning to drive.
Page 296 Features and controls Changing the function settings (With ignition CAUTION switch in the “ON” position) For safety, stop the vehicle before operating. N00556800084 While driving, even if you operate the multi-infor- 1. Park your vehicle in a safe place. mation meter switch, the function setting screen is Fully apply the parking brake and move the shift lever not displayed.
Page 297 Refer to “Changing the fuel consumption display unit” on page 3-204. Refer to “Changing the temperature unit” on page 3-206. Refer to “Changing the display language” on page 3-206. Refer to “Changing the language on Mitsubishi Multi- ® Communication System or Bluetooth 2.0 interface to match the multi-information display (if so equipped)”...
Page 298 Features and controls Manual reset mode Type 1 • If you press and hold the multi-information meter switch when the average fuel consumption and average speed are displayed, these calculations will be reset to zero. • When the ignition switch is turned to the “ON” position from the “ACC”...
Page 299 Features and controls Changing the fuel consumption display unit 2. Lightly press the multi-information meter switch to select “AVG UNIT” (fuel consumption display unit setting). N00557100130 The fuel consumption display unit can be changed. The dis- tance, speed, and amount units are also changed to match the Type 1 selected fuel consumption unit.
Page 300 Features and controls NOTE 3. Press and hold the multi-information meter switch (for The display units for the driving range, the average fuel about 2 seconds or more) to display “AVG UNIT” (fuel consumption, the average speed and the momentary fuel consumption display unit setting).
Page 301 Features and controls Changing the temperature unit 3. Press and hold the multi-information meter switch (for about 2 seconds or more) to change in sequence from °F N00557200102 The temperature display unit can be changed. → °C → °F. 1. Press and hold the multi-information meter switch (for The setting is changed to the selected temperature unit.
Page 302 2.0 interface to match the multi-information display (if so equipped) Type 2 N00529800217 The language used in Mitsubishi Multi-Communication Sys- ® tem (if so equipped) or Bluetooth 2.0 interface (if so equipped) can be changed automatically to the same language as that shown in the multi-information display.
Page 303 Type 1 The language cooperation setting can be switched in the following manner. • When “A or 1” (language cooperation: enabled) has been selected, the language for the Mitsubishi Multi- Communication System (if so equipped) or the ® Bluetooth 2.0 interface (if so equipped) is automati- cally changed to the language selected for the multi- information display.
Page 304 Features and controls Operation sound setting 2. Lightly press the multi-information meter switch to select N00557400104 “ ” (operation sound setting). You can turn off the operation sounds of the multi-information meter switch and rheostat meter illumination button. Type 1 1.
Page 305 Features and controls Changing the amount of time until “REST 3. Press and hold the multi-information meter switch (for REMINDER” is displayed about 2 seconds or more) to switch in sequence from ON (operation sound on) → OFF (operation sound off) → ON N00557500121 The amount of time until the display appears can be changed.
Page 306 Features and controls Changing the turn signal sound 3. Press and hold the multi-information meter switch (for about 2 seconds or more) to display “ALARM” (rest time N00563500038 It is possible to change the turn signal sound. setting). 1. Press and hold the multi-information meter switch for Type 1 Type 2 about 2 seconds or more to switch from the setting mode...
Page 307 Features and controls Changing the momentary fuel consumption display 3. Press and hold the multi-information meter switch for (Type 2) about 2 seconds or more to switch in sequence from 1 (turn signal sound 1) → 2 (turn signal sound 2) → 1 (turn N00563600013 It is possible to change the bar graph setting of the momentary signal sound 1).
Page 308 Features and controls Returning to the factory settings 3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from ON N00557600148 All of the function settings can be returned to their factory set- (with the green bar graph) →...
Page 309 Features and controls 3. Press and hold the multi-information meter switch (for about 5 seconds or more), the buzzer sounds and all of the function settings are returned to the factory settings. NOTE The factory settings are as follows. • Average fuel consumption and average speed reset mode: A (Auto reset) •...
Page 310 Features and controls Indicator light, warning light, and information screen display list N00557700035 Indicator and warning light list N00557800238 Type A Type B 12- ECO mode indicator (if so equipped) → P.3-196 1- Position indicator → P.3-228 13- Engine malfunction indicator (“SERVICE ENGINE SOON” 2- High beam indicator →...
Page 311 • Abnormal voltage or a static electricity discharge is generated by the operation of installed electronics (including after-mar- ket parts). If the warning display has occurred a number of times, take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice and have the system checked.
Page 312 Features and controls Warning display list (With ignition switch in the “OFF” position) N00558000165 Screen type 1 Screen type 2 Cause Do this (Reference) You have forgotten to remove the Remove the key. key from the ignition switch. Refer to “Key reminder system” on page 3-54.
Page 313 Features and controls Screen type 1 Screen type 2 Cause Do this (Reference) There is a fault in the F.A.S.T.-key. Refer to “F.A.S.T.-key” on page 3- I n f o r ma t i o n P r o v i d e d b y : 3-218...
Page 314 Features and controls Warning display list (With ignition switch in the “ON” position) N00558100238 Screen type1 Screen type 2 Cause Do this (Reference) There is a fault in the electric power Refer to “Electric power steering steering system (EPS). system (EPS)” on page 3-156. I n f o r ma t i o n P r o v i d e d b y : 3-219...
Page 315 Features and controls Screen type1 Screen type 2 Cause Do this (Reference) There is a fault in the F.A.S.T.-key. Refer to “F.A.S.T.-key” on page 3- Immobilizer is registered. Refer to “Electronic immobilizer (Anti-theft starting system)” on page 3-5, 3-41. I n f o r ma t i o n P r o v i d e d b y : 3-220...
Page 316 The brake fluid level is low. Park the vehicle in a safe place and There is a fault in the brake system. contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for assistance. Refer to “Brake warning display”...
Page 317 2-18. There is a fault in the fuel system. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the system checked. I n f o r ma t i o n P r o v i d e d b y :...
Page 318 There is a fault in the engine oil cir- Park your vehicle in a safe place as culation system. soon as possible and contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the system checked. Refer to “Oil pressure warning dis- play”...
Page 319 Screen type1 Screen type 2 Cause Do this (Reference) There is a fault in the Active Stabil- Contact an authorized Mitsubishi ity Control (ASC). Motors dealer or a repair facility of your choice to have the system checked. Refer to “Active Stability Control (ASC)”...
Page 320 The ground may be frozen even when this warning is not displayed, so drive carefully. The timing chain may be worn. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the system checked. I n f o r ma t i o n P r o v i d e d b y :...
Page 321 Features and controls Other interrupt displays (With ignition switch in the “ON” position) N00558200239 The operation status of each system is displayed on the information screen. For further details, refer to the appropriate page for each system. Screen type 1 Screen type 2 System operation status Reference...
Page 322 This informs you that a periodic inspection is due. Screen type 1 Screen type 2 Do this Have an inspection made by an authorized Mitsubishi Motors dealer. For further details, refer to “Service reminder” on page 3-198. The rest time can be set. Screen type 1...
Page 323: Warning Lights
Features and controls Indicators Warning lights N00519900127 N00520300147 Turn signal indicators/Hazard warning lights Brake warning light N00520000216 N00520400467 The arrows will flash in time with the corresponding exterior When the ignition switch is turned to the “ON” position, this turn signals when the turn signal lever is used. indicator normally comes on and goes out a few seconds later.
Page 324 The vehicle should be brought to a halt in the follow- up while driving, have the system checked as soon as possible ing manner when brake performance is deterio- at an authorized Mitsubishi Motors dealer or a repair facility of rated. your choice.
Page 325: Charging System Warning Light
If the warning light stays on while the engine is run- SST has a stronger tendency to creep forward. ning, park your vehicle in a safe place as soon as possible and contact an authorized Mitsubishi NOTE Motors dealer or a repair facility of your choice to Do not disconnect the battery cable when the engine mal- have the system checked.
Page 326: Information Screen Display
Park the vehicle in a safe place, and contact an authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 327 If warnings are displayed while the engine is run- ning, park your vehicle in a safe place as soon as possible and contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the system checked.
Page 328 If this warning display comes on when the engine oil level is proper, have your vehicle checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 329: Combination Headlights And Dimmer Switch
When the light is switched on, the heat will dry out the fog. However, if water col- lects inside the light, have it checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice. OFF All lights off...
Page 330 Features and controls If your vehicle is equipped with daytime running lights, the Type 2 combinations of switch operations and illuminated lights differ Rotate the switch to operate the lights. in accordance with the following conditions. [When the engine is started, and the parking brake is released] The daytime running lights will be illuminated: OFF The daytime running lights illuminated The daytime running lights illuminated...
Page 331 Features and controls If your vehicle is equipped with daytime running lights, the [When the engine is not running, or when the engine is running combinations of switch operations and illuminated lights differ but the parking brake is not released] in accordance with the following conditions.
Page 332 N00532600509 For further information, please contact your authorized If the ignition key is turned to “LOCK” or “ACC” posi- Mitsubishi Motors dealer or a repair facility of your tion or removed from the ignition switch and the driver’s choice. door is opened with the combination headlights and dim- Do not cover the sensor (A) for the automatic on/off con- mer switch in the “...
Page 333 “LOCK” position, the headlight reminder See your authorized Mitsubishi Motors dealer for details. buzzer intermittently emits a high-pitched sound. If the For vehicles equipped with the Mitsubishi Multi-Commu- ignition switch is in any position other than “LOCK”, the...
Page 334: Dimmer (High/Low Beam Change)
Features and controls Headlight reminder buzzer Dimmer (high/low beam change) N00549800196 N00549900155 To change the headlights from high beam to low beam and vice When using a key to start the engine versa, pull the turn signal lever to fully toward you (1). Switch If the driver’s door is opened with the key in the “LOCK”...
Page 335: Headlight Flasher
Features and controls Headlight flasher Welcome light (for vehicles with the theft-alarm system) N00550000198 You can flash the high beams by pulling the lever gently N00563200107 toward you (2). The lights will go back to normal when you let This function turns on the front side-marker and parking lights go.
Page 336: Coming Home Light
• The headlights can be set to come on in the low beam setting. • The welcome light function can be deactivated. For details, consult a Mitsubishi Motors dealer. I n f o r ma t i o n P r o v i d e d b y : 3-241...
Page 337: Headlight Leveling Switch (If So Equipped)
• The time that the headlights remain on can be changed. • The coming home light function can be deactivated. For details, consult a Mitsubishi Motors dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 338: Turn Signal Lever
Features and controls Turn signal lever NOTE Start adjusting when the knob is at the “0” position (when N00522600421 the beam is at its highest). When changing lanes, or to making a gradual turn, hold the Keep the knob in the “0” position except when using the lever in the “lane change”...
Page 339: Hazard Warning Flasher Switch
Have the vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice. The turn signal light 3-flash function for lane changes can be deactivated.
Page 340: Front Fog Light Switch (If So Equipped)
Features and controls Front fog light switch If the combination headlights and dimmer switch is (if so equipped) rotated to the “OFF” or “ ” position while the front fog N00522800377 The front fog lights illuminate only when the headlights are on lights are illuminated, they will automatically turn off.
Page 341: Wiper And Washer Switch
Features and controls Wiper and washer switch N00523000608 CAUTION If the washer is used in cold weather, the washer fluid sprayed against the glass may freeze, which may hinder visibility. Warm the glass with the defroster before using the washer. Windshield wipers N00542900013 Except for vehicle with rain sensor...
Page 342 The speed-sensitive-operation function of the windshield wipers can be deactivated. For further information, please contact your authorized Mitsubishi Motors dealer or a repair facility of your choice. On vehicles equipped with Mitsubishi Multi- Communication System, screen operations can be used to make the adjustment.
Page 343 Features and controls Vehicle with rain sensor Rain sensor (if so equipped) N00569400013 N00569500014 The windshield wipers can be operated with the ignition switch Can only be used when the ignition switch is “ON” position. in the “ON” or “ACC” position. If the lever is put in the “AUTO”...
Page 344 • A physical shock is applied to the windshield. tioning. Have the vehicle checked at an authorized • A physical shock is applied to the rain sensor. Mitsubishi Motors dealer or a repair facility of your choice. If your hands get trapped, you could suffer injuries •...
Page 345 (C). tive, or at adjustable intervals). For further information, please contact your authorized Mitsubishi Motors dealer or a repair facility of your choice. On vehicles equipped with Mitsubishi Multi-Communica- tion System, screen operations can be used to make the adjustment.
Page 346 Features and controls Misting function N00569700016 Move the lever in the direction of the arrow and release, to operate the wipers once. Use this function when you are driving in mist or drizzle. The wipers will operate once if the lever is moved to the “AUTO”...
Page 347: Windshield Washer
When the wipers are not in operation or in intermittent opera- onds. tion, by pulling the lever toward you, the wipers will operate For details, consult a Mitsubishi Motors dealer. several times while the washer fluid is being sprayed. On vehicles equipped with a Mitsubishi Multi-Communi-...
Page 348 Precautions to observe when using wipers and Replace the wiper blades when they are worn. Use the proper size replacement blades. If you have questions, ask washers your authorized Mitsubishi Motors dealer. N00523500209 CAUTION If the washer is used in cold weather, the washer fluid sprayed onto the glass might freeze, blocking your view.
Page 349: Electric Rear Window Defogger Switch
Features and controls Electric rear window defogger switch CAUTION N00523700315 The electric rear window defogger can be used when the The rear window defogger is not designed to melt snow. Remove any snow manually before using the engine is running. rear window defogger.
Page 350 Features and controls Horn switch Type 2 N00523800156 To honk the horn, press around the “ ” mark on the steering wheel. Type 1 I n f o r ma t i o n P r o v i d e d b y : 3-255...
Page 351: Bluetooth 2.0 Interface
2.0 interface and Bluetooth N00563800015 device” on page 3-264. You have acquired a device that includes software licensed by Mitsubishi Motors Corporation from JOHNSON CONTROLS ® Bluetooth is a registered trademark of BLUETOOTH SIG, Inc (the automotive experience business unit), and their subse- INC.
Page 352 Features and controls Steering control switch → P.3-258 WARNING Voice recognition function → P.3-260 Useful voice commands → P.3-261 ® Although the Bluetooth 2.0 interface allows you to Speaker enrollment function → P.3-263 make hands-free calls, if you choose to use the cellu- ®...
Page 353 Features and controls Steering control switch 1- Volume up button N00564000027 2- Volume down button Type 1 3- SPEECH button 4- PICK-UP button 5- HANG-UP button Type 2 I n f o r ma t i o n P r o v i d e d b y : 3-258...
Page 354 Features and controls Volume up button HANG-UP button Press this button to increase the volume. Press this button when an incoming call is received to refuse the call. Volume down button Press this button during a call to end the current call. Press this button to decrease the volume.
Page 355 Features and controls Voice recognition function Selecting the language 1. Press the SPEECH button. N00564100031 ® The Bluetooth 2.0 interface is equipped with a voice recogni- 2. Say “Setup.” tion function. 3. Say “Language.” Simply say voice commands and you can perform various 4.
Page 356 Features and controls Useful voice commands Confirmation function setting N00564500019 N00564200016 ® The Bluetooth 2.0 interface is equipped with a confirmation Help function function. N00564300017 With the confirmation function activated, you are given more ® The Bluetooth 2.0 interface is equipped with a help function. opportunities than normal to confirm a command when making If you say “Help”...
Page 357 Remember this passcode. It will be required to use this the voice input mode and then check with an authorized system.” Mitsubishi Motors dealer. Say a 4-digit number which you want to set as a passcode. 6. For confirmation purposes, the voice guide will say “Pass- Disabling the passcode code <4-digit passcode>.
Page 358 Features and controls Speaker enrollment function 4. The voice guide will say “This operation must be per- formed in a quiet environment while the vehicle is N00564700011 ® stopped. See the owner’s manual for the list of required The Bluetooth 2.0 interface can use the speaker enrollment training phrases.
Page 359: Bluetooth Device
(Refer to “Speaker enroll- www.mitsubishifuse.com ment” on page 3-263.） Or contact Mitsubishi hands-free customer support at (888)702-4100. I n f o r ma t i o n P r o v i d e d b y :...
Page 360 Features and controls To pair 5. The voice guide will say “Select one of the following: ® ® pair, edit, delete, or list.” Say “Pair.” To pair a Bluetooth device with the Bluetooth 2.0 interface, follow the steps below. NOTE If 7 devices have already been paired, the voice guide will NOTE say “Maximum devices paired”...
Page 361 Features and controls Selecting a device 7. The voice guide will say “Start pairing procedure on the device. See the device manual for instructions.” Enter in N00565100012 ® If multiple paired Bluetooth devices are available in the vehi- ® the Bluetooth device the 4-digit number you have regis- cle, the cellular phone or music player most recently connected tered in Step 6.
Page 362 Features and controls ® 5. The selected music player will be connected to the 5. The selected phone will be connected to the Bluetooth ® 2.0 interface. The voice guide will say “<device tag> Bluetooth 2.0 interface. selected” and then the system will return to the main The voice guide will say “<device tag>...
Page 363 Features and controls NOTE 7. The voice guide will say “Deleted,” and then the system If you press and release the SPEECH button and say will end the device deletion process. “Continue” or “Previous” while the list is being read, the NOTE system will advance or rewind the list.
Page 364 Features and controls Operating a music player connected via 5. The voice guide will say “Please say,” and read out the ® ® numbers of the Bluetooth devices and device tags of cor- Bluetooth ® responding devices in order, starting with the Bluetooth N00565400015 ®...
Page 365 Features and controls To make a call The maximum supported telephone number length is as follows: N00565600033 You can make a call in the following 3 ways using the • International telephone number: + and telephone num- ® bers (to 18 digits). Bluetooth 2.0 interface: •...
Page 366 Features and controls 4. If there is only 1 match, the system will proceed to Step 5. 5. If only 1 telephone number is registered under the name If there are 2 or more matches, the voice guide will say you just said, the voice guide will proceed to Step 6.
Page 367 Features and controls Receiving calls 6. The voice guide will say “Calling <name> <location>” and then the system will dial the telephone number. N00565800019 If an incoming phone call is received while the ignition switch NOTE is in the “ACC” or “ON” position, the audio system will be When the confirmation function is on, the system will automatically turned on and switched to the incoming call, check if the name and location of the receiver are correct.
Page 368 Features and controls Phonebook function Mute function N00565900010 N00566000018 At any time during a call, you can mute the vehicle micro- ® The Bluetooth 2.0 interface has 2 types of unique phonebooks phone. that are different from the phonebook stored in the cellular Pressing the SPEECH button and then saying “Mute”...
Page 369 Features and controls To register a telephone number in the vehicle phonebook 5. When the name has been registered, the voice guide will You can register a telephone number in the vehicle phonebook say “home, work, mobile, or other?” Say the location for in the following 2 ways: Reading out a telephone number, and which you want to register a telephone number.
Page 370 Features and controls To select and transfer one phonebook entry from the 7. The voice guide will repeat the telephone number you phonebook of the cellular phone have just read, and then register the number. You can select 1 phonebook entry from the phonebook of the When the telephone number has been registered, the voice cellular phone and register it in the vehicle phonebook.
Page 371 Features and controls 4. The voice guide will say “Would you like to import a sin- 7. When the reception is complete, the voice guide will say gle entry or all contacts?” Say “Single entry.” “<Number of telephone numbers that had been registered in the import source>...
Page 372 Features and controls To change the content registered in the vehicle phonebook 6. The voice guide will say “Number, please.” Say the tele- You can change or delete a name or telephone number regis- phone number you want to register. tered in the vehicle phonebook.
Page 373 Features and controls [Editing a name] [Listening to the list of registered names] 1. Press the SPEECH button. 1. Press the SPEECH button. 2. Say “Phonebook.” 2. Say “Phonebook.” 3. The voice guide will say “Select one of the following: 3.
Page 374 Features and controls [Deleting a telephone number] 6. The system will ask if you really want to delete the 1. Press the SPEECH button. selected telephone number(s) to go ahead with the dele- tion, answer “Yes.” 2. Say “Phonebook.” Answer “No,” the system will cancel deleting the tele- 3.
Page 375 Features and controls Erasing the phonebook Mobile phonebook You can delete all registered information from the vehicle N00566200036 All entries in the phonebook stored in the cellular phone can be phonebook. transferred in a batch and registered in the mobile phonebook. 1.
Page 376 Features and controls To import a devices phonebook 5. The voice guide will say “Importing the contact list from Follow the steps below to transfer to the mobile phonebook the the mobile phonebook. This may take several minutes to phonebook stored in the cellular phone. complete.
Page 377 Features and controls General information Enrollment commands N00566300040 N00566400038 MODEL: MMC FCC ID: CB2MDGMY10 IC: 279B- MDGMY10 ® Your Bluetooth 2.0 interface operates on a radio frequency subject to Federal Communications Commission (FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada Rules (For vehicles sold in Canada).
Page 378: Usb Input Terminal (If So Equipped)
Features and controls USB input terminal How to connect a USB memory device (if so equipped) N00566800074 N00566700015 You can connect your USB memory device or iPod* to play 1. Park your vehicle in a safe place and turn the ignition music files stored in the USB memory device or iPod.
Page 379 Features and controls 3. Connect a commercially available USB connector cable 4. Connect the USB connector cable (C) to the USB input (C) to the USB memory device (B). terminal (D). WARNING An open glove compartment door can cause a seri- ous injury or death to the front passenger in an acci- dent, even if the passenger is wearing his/her seat belt.
Page 380: How To Connect An Ipod
Features and controls How to connect an iPod NOTE Do not connect the USB memory device to the USB input N00566900020 terminal directly. 1. Park your vehicle in a safe place and turn the ignition The USB memory device may be damaged. switch to the “LOCK”...
Page 381 Features and controls 3. Connect the Dock connector (C) to the iPod (B). 4. Connect the Dock connector (C) to the USB input termi- nal (D). NOTE Use a genuine Dock connector from Apple Inc. WARNING An open glove compartment door can cause a seri- ous injury or death to the front passenger in an acci- dent, even if the passenger is wearing his/her seat belt.
Page 382: Specifications
Features and controls NOTE 5. To remove the Dock connector, turn the ignition switch to Depending on the type of the USB memory device or the “LOCK” position first and perform the installation other device connected, the connected device may not steps in reverse.
Page 383: Sun Visors
Features and controls Sun visors File specifications N00567200017 N00524600308 Fold the sun visor downward (1) to reduce front glare while You can play music files of the following specifications that driving. To reduce side glare, turn the visor to the side (2). are saved in a USB memory device or other device supporting mass storage class.
Page 384: Vanity Mirror
Features and controls Vanity mirror Card holder The vanity mirrors are located on the back of the sun visors. Cards can be slipped into the front (A) of the lid of the vanity mirror. I n f o r ma t i o n P r o v i d e d b y : 3-289...
Page 385: V Power Outlet
Features and controls 12 V power outlet Type 1, Type 2 The accessory can be operated when the ignition switch is in N00525000556 the “ON” or “ACC” position. CAUTION To use a “plug-in” type accessory, pull out the plug, then insert the plug in the socket.
Page 386 Features and controls Type 3 (if so equipped) Type 2 The accessory can be operated when the ignition switch is in any position. To use a “plug-in” type accessory, open the cover, then insert the plug in the socket. I n f o r ma t i o n P r o v i d e d b y : 3-291...
Page 387: Interior Lights
Features and controls Interior lights Dome light (Front)/Reading lights (if so equipped) N00525800192 N00525300461 Dome light (Front) The dome light can be turned on by sliding the dome light switch. 1- Dome light (Rear) (if so equipped) → P.3-294 2- Dome light (Front)/Reading lights (if so equipped) → P.3- I n f o r ma t i o n P r o v i d e d b y : 3-292...
Page 388 The driver’s door is closed after all the other doors are The time until the light goes off can be adjusted. See closed while the lock knob of the driver’s door is in the your authorized Mitsubishi Motors dealer for details. lock position. For vehicles equipped with the Mitsubishi Multi-Com-...
Page 389 Features and controls Dome light (Rear) Reading lights (if so equipped) N00553800067 N00525400361 Regardless of the dome light switch position, when you press The dome light can be turned on by sliding the dome light the lens, the light on the side that is pressed illuminates; when switch.
Page 390 The door is closed while the ignition switch is in the The time until the light goes off can be adjusted. See “ON” position. your authorized Mitsubishi Motors dealer for details. The driver’s door is closed after all the other doors are For vehicles equipped with the Mitsubishi Multi-Com- closed while the lock knob of the driver’s door is in the...
Page 391: Storage Spaces
A lid or the contents of a storage space The time until the lights automatically go off can be could otherwise cause injuries during a sudden stop. adjusted. See your authorized Mitsubishi Motors dealer for details. For vehicles equipped with the Mitsubishi Multi-Commu-...
Page 392 Features and controls [Except for RALLIART] [RALLIART] 1- Floor console box (if so equipped) → P.3-300 1- Luggage floor boxes → P.3-301 2- Front console tray (if so equipped) → P.3-299 2- Floor console box → P.3-300 3- Front console boxes (if so equipped) → P.3-299 3- Front console tray (if so equipped) →...
Page 393: Glove Compartment
Features and controls Glove compartment Card holder N00551500246 To open the glove compartment, pull the lever (A). There is a card holder on the inside of the glove compartment. NOTE WARNING Up to 2 cards will fit in the card holder. An open glove compartment door can cause a seri- ous injury or death to the front passenger in an acci- dent, even if the passenger is wearing his/her seat...
Page 394 Features and controls Front console tray Front console boxes (if so equipped) (if so equipped) N00547800017 N00546400058 The front console tray is on the front console part. To open, push the lid. Upper box CAUTION NOTE Do not use the front console tray as an ashtray. The Auxiliary Audio connector (RCA) (if so equipped) or This could cause a fire.
Page 395 Features and controls Floor console box with lid Lower box (if so equipped) N00551600188 To open the floor console box, lift the release lever (A) and raise the lid. CAUTION Do not use the front console boxes as an ashtray. This could cause a fire.
Page 396 Features and controls Luggage floor boxes Tissue holder (if so equipped) The tissue holder (A) is located on the underside of the floor N00552400066 The boxes for storing articles are located inside the luggage console box lid. compartment. To use the boxes, remove the floor mat (A) and raise the lids (B).
Page 397: Cup Holder
Features and controls Cup holder Type 2 To use the cup holder, open up the lid. N00527300351 For the front seat The cup holder is located the middle of the floor console. The cup holder is designed for holding cups or drink-cans securely.
Page 398: Bottle Holder
Features and controls For the rear seat Bottle holder (if so equipped) N00537000159 N00502800049 This cup holder is located in the rear seat arm rest (A). Pull the rear arm rest down to use the cup holder. CAUTION Do not drink beverages while driving your vehicle. This is distracting and could cause an accident.
Page 399: Assist Grip
Features and controls Assist grip Coat hook (if so equipped) N00559000029 N00553600108 These grips are to support the body by hand while seated in the There is a coat hook on the rear seat assist grip of the driver’s vehicle. side.
Page 400 I n f o r ma t i o n P r o v i d e d b y :...
Page 401 I n f o r ma t i o n P r o v i d e d b y :...
Page 402: Driving Safety
Driving safety Fuel economy......4- Driving, alcohol and drugs....4- Floor mat .
Page 403: Fuel Economy
Driving safety Fuel economy Driving, alcohol and drugs N00628800165 N00628900052 Fuel economy is dependent on many factors. Your personal Drunk driving is one of the most frequent causes of accidents. driving habits can have a significant effect on your fuel use. Your driving ability can be seriously impaired even with blood Several recommendations for achieving the greatest fuel econ- alcohol levels far below the legal minimum.
Page 404: Floor Mat
To prevent the floor mat from moving forward and possibly interfering with the operation of the pedals, Mitsubishi genuine floor mats are recommended. To install the floor mat N00628700050 1.
Page 405 Never install a second mat over or under an existing floor mat. Do not use a floor mat designed for another model vehicle even if it is a Mitsubishi genuine floor mat. Before driving, be sure to check the following: • Periodically check that the floor mat is properly secured with the retaining clips.
Page 406: Vehicle Preparation Before Driving
Move the driver’s seat as far backward as possible, while should, therefore, be performed only by an authorized still keeping good visibility, and good control of the steer- Mitsubishi Motors dealer. ing wheel, brakes, accelerator, and controls. Check the Lights instrument panel indicators and multi-information display for any possible problem.
Page 407: Safe Driving Techniques
Driving safety Safe driving techniques Driving during cold weather N00629200111 N00629400344 Even this vehicle’s safety equipment, and your safest driving, Check the battery, including terminals and cables. During cannot guarantee that you can avoid an accident or injury. extremely cold weather, the battery will not be as strong. However, if you give extra attention to the following areas, you Also, the battery power level may drop because more can better protect yourself and your passengers:...
Page 408 Never open the radiator cap when the radiator is hot. You could be seriously burned. [For RALLIART vehicles sold in U.S.A.] Mitsubishi Motors recommends that the standard equip- ment tires be replaced with winter tires when the vehicle is going to be used in winter.
Page 409 All the parts of the brake system are critical to safety. Have the Parking on a hill vehicle serviced by an authorized Mitsubishi Motors dealer or When parking on a hill, set the parking brake, and turn the a repair facility of your choice at regular intervals according to front wheels toward the curb on a downhill, or away from the the “WARRANTY AND MAINTENANCE MANUAL”.
Page 410: Loading Information
Driving safety Loading information WARNING N00629900349 Leaving the engine running risks injury or death It is very important to know how much weight your vehicle can from accidentally moving the gearshift lever (man- carry. This weight is called the vehicle capacity weight and ual transaxle or Twin Clutch SST) or the selector includes the weight of all occupants, cargo and non-factory- lever (CVT) or from the accumulation of toxic...
Page 411: Tire And Loading Information Placard
Driving safety Tire and loading information placard Curb weight: the weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, N00630100309 The tire and loading information placard is located on the and coolant. driver’s door sill. Accessory weight: the combined weight (in excess of those standard items which may be replaced) of automatic transmission, power steering, power brakes, power win-...
Page 412 Driving safety This placard shows the maximum number of occupants permit- Type 2 ted to ride in your vehicle as well as “the combined weight of occupants and cargo” (A), which is called the vehicle capacity weight. The weight of roof road is included in the definition of “cargo”...
Page 413: Steps For Determining Correct Load Limit
Driving safety Steps for Determining Correct Load Limit N00630200182 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and pas- sengers that will be riding in your vehicle.
Page 414 Driving safety NOTE The following table shows examples on how to calculate total cargo/load capacity of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load capacity of your vehicle.
Page 415: Cargo Loads
Driving safety Cargo loads WARNING N00629700464 To reduce the risk of serious injury or death, the Cargo load precautions combined weights of the driver, passengers and To determine the cargo load capacity for your vehicle, subtract cargo and must never exceed the vehicle capacity the weight of all vehicle occupants from the vehicle capacity weight.
Page 416: Trailer Towing
Driving safety Trailer towing N00629800188 WARNING Do not use this vehicle for trailer towing. It may not be possible to maintain control or adequate braking. I n f o r ma t i o n P r o v i d e d b y : 4-15...
Page 417 I n f o r ma t i o n P r o v i d e d b y :...
Page 418: Comfort Controls
Comfort controls To play tracks from a Bluetooth® device Vents........5- (vehicles with Bluetooth®...
Page 419 Comfort controls Vents Air flow and direction adjustments N00730200301 N00729900210 Center vents Move the knob to make adjustments. To close the vent, move the knob to the inside as far as possi- ble. Left Right 1- Center vents 2- Side vents A- Knob 1- Close 2- Open...
Page 420 Comfort controls Changing the mode selection Side vents Move the knob to make adjustments. N00736400493 To change the position and amount of air flowing from the To close the vent, move the knob to the outside as far as possi- vents, turn the mode selection dial.
Page 421 Comfort controls Foot/Face position Foot position Air flows to the upper part of the passenger compartment, and Air flows mainly to the leg area. flows to the leg area. *- if so equipped *- if so equipped NOTE With the mode selection dial between the “ ”...
Page 422 Comfort controls Foot/Defroster position Defroster position Air flows to the leg area, the windshield and the door windows. Air flows mainly to the windshield and the door windows. *- if so equipped NOTE With the mode selection dial between the “ ”...
Page 423: Control Panel
Comfort controls Heater without air conditioning function Blower speed selection dial N00737900020 so equipped) When the ignition switch is in the “ON” position, select the N00737700031 blower speed by turning the blower speed selection dial. The heater can only be used while the engine is running. Turning the dial clockwise will increase the blower speed;...
Page 424 Comfort controls Temperature control dial Mode selection dial N00738000044 N00738100058 Turn the temperature control dial clockwise to make the air To change the amount of air flowing from the vents, turn the warmer. Turn it counterclockwise to make the air cooler. mode selection dial.
Page 425 Comfort controls Air selection switch If the outside air is dusty or contaminated in some way, use the recirculation position. Switch to the outside air position every N00738200033 Normally, use the outside air position to keep the windshield now and then to keep the windows from fogging up. and side windows clear and to quickly remove fog or frost from the windshield.
Page 426 Comfort controls Operating the system NOTE For quick heating, set the blower speed selection dial to N00738300034 the position shown in the illustration. Heating Set the mode selection dial to the “ ” position and set the air selection switch (A) to the outside air position. Turn the temperature control dial clockwise or counterclock- wise to the desired temperature.
Page 427 Comfort controls Combination of unheated air and heated air Defrosting or defogging the windshield and door win- dows N00738400022 Set the mode selection dial to the positions shown in the illus- N00738500065 tration and set the air selection switch (A) to the outside air CAUTION position.
Page 428 Comfort controls For ordinary defrosting For quick defrosting Use this setting to keep the windshield and door windows clear of mist, and to keep the leg area heated (when driving in rain or snow). 1. Set the mode selection dial to the “ ”...
Page 429 Comfort controls Manual air conditioning with MAX A/C Blower speed selection dial mode N00736500146 (if so equipped) When the ignition switch is in the “ON” position, select the blower speed by turning the blower speed selection dial. N00730300256 The air conditioning can only be used while the engine is run- Turning the dial clockwise will increase the blower speed;...
Page 430 Comfort controls Temperature control dial Mode selection dial N00736600219 N00736700151 Turn the temperature control dial clockwise to make the air To change the amount of air flowing from the vents, turn the warmer. Turn it counterclockwise to make the air cooler. mode selection dial.
Page 431 Comfort controls Air selection switch NOTE When the air conditioning operates with the air selection N00736800367 Normally, use the outside air position to keep the windshield switch (A) in the outside air position, the system automat- and side windows clear and to quickly remove fog or frost ically determines whether to continue using outside air or from the windshield.
Page 432 Comfort controls Personalizing the air selection (Changing the function NOTE setting) While the mode selection dial is set between “ ” and “ ” position, the air conditioning compressor will run N00702100015 You can change the following functions to match your prefer- automatically.
Page 433 If the air conditioning indicator light (A) does not blink, there is no problem. If it does blink, have it checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice.
Page 434 Comfort controls Operating the air conditioning system NOTE For quick heating, set the blower speed selection dial to N00731100222 the position shown in the illustration. Heating Set the mode selection dial to the “ ” position and set the air selection switch (A) to the outside air position.
Page 435 Comfort controls Cooling NOTE If the outside air is dusty or contaminated in some way, N00731200278 push the air selection switch (A) to set it to the recircula- For ordinary cooling tion position. Let in some outside air from time to time for good ventilation.
Page 436 Comfort controls Combination of unheated air and heated air NOTE When the temperature control dial is set to the “MAX N00731300211 Set the mode selection dial to one of the positions shown in the A/C” position, the air conditioning compressor will run illustration and set the air selection switch (A) to the outside air automatically and the light will come on.
Page 437 Comfort controls Defrosting or defogging (windshield, door windows) For ordinary defrosting Use this setting to keep the windshield and door windows clear N00731400443 of mist, and to keep the leg area heated (when driving in rain or CAUTION snow). For safety, make sure you have a clear view through all the windows.
Page 438 Comfort controls For quick defrosting NOTE While the mode selection dial is set between “ ” and “ ” position, the air conditioning compressor will run automatically. The outside air position will also be auto- matically selected. (In this case, the air conditioning indi- cator will not change.) While the between “...
Page 439 Comfort controls Manual air conditioning without MAX A/C Blower speed selection dial mode N00736500133 (if so equipped) When the ignition switch is in the “ON” position, select the blower speed by turning the blower speed selection dial. N00730300269 The air conditioning can only be used while the engine is run- Turning the dial clockwise will increase the blower speed;...
Page 440 Comfort controls Temperature control dial Mode selection dial N00736600176 N00736700177 Turn the temperature control dial clockwise to make the air To change the amount of air flowing from the vents, turn the warmer. Turn it counterclockwise to make the air cooler. mode selection dial.
Page 441 Comfort controls Air selection switch NOTE When the air conditioning operates with the air selection N00736800279 Normally, use the outside air position to keep the windshield switch (A) in the outside air position, the system automat- and side windows clear and to quickly remove fog or frost ically determines whether to continue using outside air or from the windshield.
Page 442 Comfort controls Personalizing the air selection (Changing the function Air conditioning switch setting) N00731000436 Push the switch, and the air conditioning compressor will turn N00702100028 on. The air conditioning indicator light (A) will come on. You can change the following functions to match your prefer- A sound will be made every time you push the switch.
Page 443 (A) does not blink, there is no problem. If it does Turn the temperature control dial clockwise or counterclock- blink, have it checked at an authorized Mitsubishi Motors wise to the desired temperature. Select the best speed to fit dealer or a repair facility of your choice.
Page 444 Comfort controls Cooling NOTE For quick heating, set the blower speed selection dial to N00731200249 the position shown in the illustration. For ordinary cooling 1. Set the mode selection dial to the “ ” position. 2. Push the air selection switch (A) to set it to the outside air position.
Page 445 Comfort controls Combination of unheated air and heated air NOTE If the outside air is dusty or contaminated in some way, N00731300224 Set the mode selection dial to the positions shown in the illus- push the air selection switch (A) to set it to the recircula- tration and set the air selection switch (A) to the outside air tion position.
Page 446 Comfort controls Defrosting or defogging (windshield, door windows) For ordinary defrosting Use this setting to keep the windshield and door windows clear N00731400456 of mist, and to keep the leg area heated (when driving in rain or CAUTION snow). For safety, make sure you have a clear view through all the windows.
Page 447 Comfort controls For quick defrosting NOTE While the mode selection dial is set to the “ ” position, the air conditioning compressor will run automatically. The outside air position will also be automatically selected. To defog quickly, direct the air flow from the side vents toward the door windows.
Page 448 Comfort controls Automatic air conditioning with Fahrenheit NOTE There is an interior air temperature sensor (A) in the illus- scale (if so equipped) trated position. N00731500226 Never place anything over the sensor, since doing so will The air conditioning can only be used while the engine is run- prevent it from functioning properly.
Page 449 Comfort controls Blower speed selection dial Temperature control dial N00736900094 N00737000265 When the ignition switch is in the “ON” position, select the Use this dial to adjust the temperature in the passenger com- blower speed by turning the blower speed selection dial. partment.
Page 450 The above indicates the factory settings. You can personalize the air selection switch and air conditioning switch to match your personal preferences. Contact your Mitsubishi Motors dealer or a repair facility of your choice for assistance. Refer to “Personalizing the air conditioning switch (Changing the function setting)”...
Page 451 Comfort controls Air selection switch When the air conditioning turns on, the air selection is con- trolled automatically. When the air conditioning turns off, the N00737200238 Normally, use the outside air position to keep the windshield air selection automatically goes back to the outside air position. and side windows clear and to quickly remove fog or frost If high cooling performance is desired, or if the outside air is from the windshield.
Page 452 Comfort controls Personalizing the air selection (Changing the function NOTE The factory setting is “Enable automatic air control”. setting) While the mode selection dial is set between “ ” and N00760000018 You can change the following functions to match your prefer- “...
Page 453 If the air conditioning indicator light does not blink there is no problem. If it does blink, have it checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice. Sometimes, for example after using a high-pressure car wash, the condenser can get wet, and the air conditioning indicator light (A) blinks temporarily.
Page 454 Comfort controls Personalizing the air conditioning switch (Changing NOTE The factory setting is “Enable automatic air conditioning the function setting) control”. N00759800032 You can change the following functions to match your prefer- While the mode selection dial is set between “ ”...
Page 455 Comfort controls Operating the air conditioning system (automatic NOTE Set the temperature at about 75 under normal conditions. mode) While the engine coolant temperature is low, the tempera- N00731700345 ture of the air from the heater will be cool/cold until the engine warms up, even if you have selected warm air with the dial.
Page 456 Comfort controls Operating the air conditioning system (manual For ordinary defrosting Use this setting to keep the windshield and door windows clear mode) of mist, and to keep the leg area heated (when driving in rain or N00731800072 snow). Blower speed and vent mode may be controlled manually by setting the blower speed selection dial and the mode selection dial to the desired positions.
Page 457 Comfort controls For quick defrosting NOTE While the mode selection dial is set between “ ” and “ ” position, the air conditioning compressor will run automatically. The outside air position will also be selected automatically. If the mode selection dial is set between “ ”...
Page 458 Comfort controls Automatic air conditioning with Celsius NOTE There is an interior air temperature sensor (A) in the illus- scale (if so equipped) trated position. N00731500239 Never place anything over the sensor, since doing so will The air conditioning can only be used while the engine is run- prevent it from functioning properly.
Page 459 Comfort controls Blower speed selection dial Temperature control dial N00736900111 N00737000281 When the ignition switch is in the “ON” position, select the Use this dial to adjust the temperature in the passenger com- blower speed by turning the blower speed selection dial. partment.
Page 460 The above indicates the factory settings. You can personalize the air selection switch and air conditioning switch to match your personal preferences. Contact your Mitsubishi Motors dealer or a repair facility of your choice for assistance. Refer to “Personalizing the air conditioning switch (Changing the function setting)”...
Page 461 Comfort controls Air selection switch When the air conditioning turns on, the air selection is con- trolled automatically. When the air conditioning turns off, the N00737200241 Normally, use the outside air position to keep the windshield air selection automatically goes back to the outside air position. and side windows clear and to quickly remove fog or frost If high cooling performance is desired, or if the outside air is from the windshield.
Page 462 Comfort controls Personalizing the air selection (Changing the function NOTE The factory setting is “Enable automatic air control”. setting) While the mode selection dial is set to the “ ” position, N00760000050 You can change the following functions to match your prefer- the air selection will automatically change to the outside ence.
Page 463 If the air conditioning indicator light does not blink there is no problem. If it does blink, have it checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice. Sometimes, for example after using a high-pressure car wash, the condenser can get wet, and the air conditioning indicator light (A) blinks temporarily.
Page 464 Comfort controls Personalizing the air conditioning switch (Changing NOTE The factory setting is “Enable automatic air conditioning the function setting) control”. N00759800029 You can change the following functions to match your prefer- While the mode selection dial is set to the “ ”...
Page 465 Comfort controls Operating the air conditioning system (automatic NOTE Set the temperature at about 25 under normal conditions. mode) While the engine coolant temperature is low, the tempera- N00731700286 ture of the air from the heater will be cool/cold until the engine warms up, even if you have selected warm air with the dial.
Page 466 Comfort controls Operating the air conditioning system (manual For ordinary defrosting Use this setting to keep the windshield and door windows clear mode) of mist, and to keep the leg area heated (when driving in rain or N00731800098 snow). Blower speed and vent mode may be controlled manually by setting the blower speed selection dial and the mode selection dial to the desired positions.
Page 467 Comfort controls For quick defrosting NOTE While the mode selection dial is set to the “ ” position, the air conditioning compressor will run automatically. The outside air position will also be selected automati- cally. While the “ ” position is selected, you cannot turn the air conditioning off or select the recirculation position.
Page 468: Important Air Conditioning Operating Tips
This includes the quick might be a refrigerant leak. defrosting mode. Operating the air condition system weekly Have the system inspected by your authorized Mitsubishi maintains lubrication of the compressor internal parts to keep Motors dealer or a repair facility of your choice.
Page 469: Air Purifier
Mitsubishi Motors dealer or a repair facility of your choice. Never try to repair it yourself. Avoid using the audio system until it is inspected by a qualified person.
Page 470 Comfort controls ™ SIRIUS Satellite Radio (if so equipped) N00760100080 Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is SIRIUS Satellite Radio. This service offers over 100 channels of music, sports, news, enter- tainment, and programming for listeners, directly from its sat- ellites and broadcasting studios.
Page 471 Comfort controls Volume and tone control panel N00711900598 1- PWR (On-Off) switch 2- VOL (Volume control) knob 3- Display 4- SOUND (Sound control) switch I n f o r ma t i o n P r o v i d e d b y : 5-54...
Page 472 Comfort controls To adjust the volume To adjust the tone N00712000365 N00712100597 Turn the VOL knob (2) clockwise to increase the volume; 1. Press the SOUND switch (4) repeatedly to select the tone counterclockwise to decrease the volume. or balance control to change. The order is: TYPE → The status will be displayed in the display (3).
Page 473 Comfort controls 2. Turn the SOUND switch (4) either clockwise or counter- Sound control switch operation clockwise to change the tone/balance setting. Adjust Adjust level The status will be displayed in the display (3). Counterclock- mode Clockwise turn wise turn NORMAL ↔...
Page 474 Comfort controls TYPE (Acoustic characteristic selection) FIELD (Sound field selection) To select the desired acoustic characteristic. To select the desired sound field. Acoustic characteristic Description Sound field type Description Sounds good for all types of Allows the listeners to enjoy an NORMAL music.
Page 475 Comfort controls Speed Compensated Volume function BASS (Bass tone control) To select the desired bass level. N00752200154 Speed Compensated Volume function is a feature that automat- MID (Midrange tone control) ically adjusts the VOLUME, BASS, MIDDLE, and TREBLE To select the desired midrange level. settings in accordance with the vehicle speed.
Page 476 Comfort controls Radio control panel and display N00734900700 1- RADIO (AM/FM selection) button 2- PWR (On-Off) switch 3- PAGE button 4- DISP (Display) button 5- SEEK (Down-seek) button 6- SEEK (Up-seek) button 7- TUNE switch 8- PTY (Program Type) button 9- SCAN button 10- Memory select buttons 11- FM (FM1/FM2) display...
Page 477 Comfort controls To listen to the radio To store a frequency in the memory, follow these steps: 1. Press the SEEK button (5 or 6), or turn the TUNE switch N00735000766 1. Press the PWR switch (2) to turn the audio system ON and (7) to tune to the frequency you wish to keep in the mem- OFF.
Page 478 Comfort controls Radio broadcast data system (RBDS) To search for a broadcast of desired PTY 1. To enter PTY (Program Type) mode, press the PTY button N00751800052 RBDS features are available for use only on FM stations that (8) during FM reception. broadcast RBDS information.
Page 479 Comfort controls NOTE If you wish to listen to another station of the same PTY as currently selected, repeat the previous procedure from step 2. To display the station name and the PTY, press the DISP button (4) and the PTY button (8) respectively. If no station is found with your desired PTY, “EMPTY”...
Page 480 Comfort controls Text message The radio can receive text messages broadcast by some RBDS stations. 1. While tuning in to an RBDS station, press the DISP but- ton (4). 2. A text message will appear on the display. If a station name appears, press the DISP button again, then the text message will be displayed.
Page 481 Comfort controls SIRIUS satellite radio control panel and display N00700200171 1- RADIO (AM/FM/Satellite radio selection) button 2- PWR (On-Off) switch 3- PAGE button 4- DISP (Display) button 5- Channel selection down button 6- Channel selection up button 7- TUNE/SOUND (Category selection) switch 8- PTY button 9- SCAN button 10- Memory select buttons...
Page 482 Comfort controls To listen to the SIRIUS satellite radio Pressing the PTY button (8) while in the category selec- tion mode will cause the current channel to be displayed N00760500143 for around 2 seconds. 1. Press the PWR switch (2) to turn the audio system ON and OFF.
Page 483 Comfort controls To enter channels into the memory SIRIUS ID indication You can save one channel to each Memory select button (10), If you press a channel selection button (5 or 6) to select “CH for a maximum of 24 channels in memory. 0,”...
Page 484 If the channel that is currently being received is not enabled. locked, you can select “LOCK CH”; if it is locked, you If the vehicle is equipped with a Mitsubishi Motors autho- can select “UNLOCK CH.” rized hands-free phone system, “PHONE OFF” will not be displayed.
Page 485 Comfort controls To skip a desired channel To cancel skip settings You can set any channel to be skipped during channel selec- You can cancel skip settings on channels. tion. 1. Press the TUNE/SOUND switch (7) for about 2 seconds 1.
Page 486 Comfort controls To unlock locked channels 5. Use the Memory select buttons (10) to enter the code There are two ways to unlock a locked channel. One way is to (1111 to 6666) and then press the TUNE/SOUND switch unlock a single locked channel of your choice. The other way (7).
Page 487 Comfort controls To change the lock cancellation code NOTE The default factory setting for the code is “1111.” You can change the code for unlocking channel(s) to any num- You can change the code to any number you want with the ber you want.
Page 488 Comfort controls Text message 7. “STORED” will be displayed for 2 seconds, the code will be changed and the satellite radio will return to the LOCK You can change what is shown on the display when the satellite radio tunes into a channel. setting mode.
Page 489 Comfort controls CD control panel and display N00735300600 1- RADIO (AM/FM selection) button 2- CD (CD mode changeover) button 3- PWR (On-Off) switch 4- PAGE button 5- DISP (Display) button 6- RPT (Repeat) button 7- RDM (Random) button 8- Fast-reverse button 9- Fast-forward button 10- SCAN button 11- Eject button...
Page 490 Comfort controls To listen to a CD To listen to a music CD N00735501045 To set discs 1. Press the PWR switch (3) to turn the audio system ON and OFF. The system turns on in the last mode used. 2.
Page 491 Comfort controls To listen to an MP3 CD NOTE While listening to a disc on which CD-DA (CD-Digital This CD player allows you to play MP3 (MPEG Audio Layer- 3) files recorded on CD-ROMs, CD-Rs (recordable CDs), and Audio) and MP3 files have both been recorded, you can switch between reading of the CD-DA, reading of the CD-RWs (rewritable CDs) in ISO9660 Level 1/ Level 2, Joliet, MP3 files, and the external audio input mode by pressing...
Page 492 Comfort controls Folder selection order/MP3 file playback order (Example) To fast forward/reverse the disc To fast forward or fast reverse the disc, press the fast-forward button (9) or the fast-reverse button (8). Root folder (Root directory) Fast forward You can fast forward the disc by pressing the fast-forward but- ton (9).
Page 493 Comfort controls To select a desired folder (MP3 CDs only) To select a desired track You can select your desired folder by turning the FOLDER You can select your desired track by using the TRACK button switch (13). (14). Track up Press the side of the TRACK button (14) repeatedly until the desired track number appears on the display.
Page 494 Comfort controls To change the order of tracks for playback Random playback for a disc (music CDs only) Press the RDM button (7) briefly. “RDM” will appear on the display. Tracks on the currently selected disc will be played in a random sequence.
Page 495 Comfort controls Random playback for all folders on a disc (MP3 CDs only) To find the start of each track on a disc for playback Press the RDM button (7) for 2 seconds or longer (until you Press the SCAN button (10). “SCAN” will appear on the dis- hear a beep).
Page 496 Comfort controls CD text and MP3 title display MP3 title The CD player can display folder and track titles for discs N00752100137 This CD player can display CD text and MP3 titles including encoded with folder and track information. Press the DISP but- ID3 tag information.
Page 497 “•”. turn off the audio system and have it checked at an autho- rized Mitsubishi Motors dealer or a repair facility of your choice. Never try to repair it yourself. Avoid using the audio system until it is inspected by a qualified person.
Page 498 Comfort controls The audio amplifier (if so equipped) is located under the ™ SIRIUS Satellite Radio (if so equipped) front left seat. N00760100107 Do not subject the amplifier to a strong impact. Satellite radio uses direct satellite to receiver broadcasting It could damage the amplifier or malfunctioning could technology to provide clear digital sound, coast to coast.
Page 499 Comfort controls Volume and tone control panel N00711900602 1- PWR (On-Off) switch 2- VOL (Volume control) knob 3- Display 4- SOUND (Sound control) switch I n f o r ma t i o n P r o v i d e d b y : 5-82...
Page 500 Comfort controls To adjust the volume To adjust the tone N00712000378 N00712100555 Turn the VOL knob (2) clockwise to increase the volume; 1. Press the SOUND switch (4) repeatedly to select the tone counterclockwise to decrease the volume. or balance control to change. The order is: SUB PUNCH The status will be displayed in the display (3).
Page 501 Comfort controls 2. Turn the SOUND switch (4) either clockwise or counter- Sound control switch operation clockwise to change the tone/balance setting. Adjust Adjust The status will be displayed in the display (3). Counterclock- Mode Level Clockwise turn wise turn 1 to 6 Weaker Stronger...
Page 502 Comfort controls SUB PUNCH (subwoofer volume control) FIELD (Sound field selection) To select the desired deep bass level. To select the desired sound field. TYPE (acoustic characteristic selection) Sound field type Description To select the desired acoustic characteristic. Optimized for the Rockford Fosgate NORMAL high bass output.
Page 503 Comfort controls BALANCE (Left/Right balance control) 2. Push the SOUND switch for at least about 2 seconds. The To balance the volume from the L (left) and the R (right) system will switch to MENU mode and the characters speakers. “SCV ON”...
Page 504 Comfort controls Radio control panel and display N00734900713 1- RADIO (AM/FM selection) button 2- PWR (On-Off) switch 3- PAGE button 4- DISP (Display) button 5- SEEK (Down-seek) button 6- SEEK (Up-seek) button 7- TUNE switch 8- PTY (Program Type) button 9- SCAN button 10- Memory select buttons 11- FM (FM1/FM2) display...
Page 505 Comfort controls To listen to the radio To store a frequency in the memory, follow these steps: 1. Press the SEEK button (5 or 6), or turn the TUNE switch N00735000779 1. Press the PWR switch (2) to turn the audio system ON and (7) to tune to the frequency you wish to keep in the mem- OFF.
Page 506 Comfort controls Radio broadcast data system (RBDS) To search for a broadcast of desired PTY 1. To enter PTY (Program Type) mode, press the PTY button N00751800065 RBDS features are available for use only on FM stations that (8) during FM reception. broadcast RBDS information.
Page 507 Comfort controls NOTE If you wish to listen to another station of the same PTY as currently selected, repeat the previous procedure from step 2. To display the station name and the PTY, press the DISP button (4) and the PTY button (8) respectively. If no station is found with your desired PTY, “EMPTY”...
Page 508 Comfort controls Text message The radio can receive text messages broadcast by some RBDS stations. 1. While tuning in to an RBDS station, press the DISP but- ton (4). 2. A text message will appear on the display. If a station name appears, press the DISP button again, then the text message will be displayed.
Page 509 Comfort controls SIRIUS satellite radio control panel and display N00700200184 1- RADIO (AM/FM/Satellite radio selection) button 2- PWR (On-Off) switch 3- PAGE button 4- DISP (Display) button 5- Channel selection down button 6- Channel selection up button 7- TUNE/SOUND (Category selection) switch 8- PTY button 9- SCAN button 10- Memory select buttons...
Page 510 Comfort controls To listen to the SIRIUS satellite radio Pressing the PTY button (8) while in the category selec- tion mode will cause the current channel to be displayed N00760500156 for around 2 seconds. 1. Press the PWR switch (2) to turn the audio system ON and OFF.
Page 511 Comfort controls To enter channels into the memory SIRIUS ID indication You can save one channel to each Memory select button (10), If you press a channel selection button (5 or 6) to select “CH for a maximum of 24 channels in memory. 0,”...
Page 512 If the channel that is currently being received is not enabled. locked, you can select “LOCK CH”; if it is locked, you If the vehicle is equipped with a Mitsubishi Motors autho- can select “UNLOCK CH.” rized hands-free phone system, “PHONE OFF” will not be displayed.
Page 513 Comfort controls To skip a desired channel To cancel skip settings You can set any channel to be skipped during channel selec- You can cancel skip settings on channels. tion. 1. Press the TUNE/SOUND switch (7) for about 2 seconds 1.
Page 514 Comfort controls To unlock locked channels 5. Use the Memory select buttons (10) to enter the code There are two ways to unlock a locked channel. One way is to (1111 to 6666) and then press the TUNE/SOUND switch unlock a single locked channel of your choice. The other way (7).
Page 515 Comfort controls To change the lock cancellation code NOTE The default factory setting for the code is “1111.” You can change the code for unlocking channel(s) to any num- You can change the code to any number you want with the ber you want.
Page 516 Comfort controls Text message 7. “STORED” will be displayed for 2 seconds, the code will be changed and the satellite radio will return to the LOCK You can change what is shown on the display when the satellite radio tunes into a channel. setting mode.
Page 517 Comfort controls CD control panel and display N00735300613 16- Disc loading slot 1- RADIO (AM/FM selection) button 17- FOLDER switch 2- CD (CD mode changeover) button 18- TRACK (Track up/down) button 3- PWR (On-Off) switch 19- Display 4- LOAD indicator 5- LOAD button 6- PAGE button 7- DISP (Display) button...
Page 518 Comfort controls To listen to a CD To set discs N00735501058 The compact disc (CD) can be loaded or ejected by pressing the LOAD button (5) or the eject button (15) even if the audio system power is OFF. 1. Press the PWR switch (3) to turn the audio system ON and OFF.
Page 519 Comfort controls To set all the discs To eject discs 1. Press the LOAD button (5) for 2 seconds or longer (until you hear a beep). 2. The autochanger will select the lowest-numbered empty slot and switch to loading standby mode. 3.
Page 520 Comfort controls To eject all the discs To listen to a music CD 1. Press the eject button (15) for 2 seconds or longer (until you hear a beep). 2. The currently selected disc will be ejected. When you remove the ejected disc, the next disc will automatically be ejected.
Page 521 Comfort controls To listen to an MP3 CD NOTE While listening to a disc on which CD-DA (CD-Digital This autochanger allows you to play MP3 (MPEG Audio Layer-3) files recorded on CD-ROMs, CD-Rs (recordable Audio) and MP3 files have both been recorded, you can switch between reading of the CD-DA, reading of the CDs), and CD-RWs (rewritable CDs) in ISO9660 Level MP3 files, and the external audio input mode by pressing...
Page 522 Comfort controls Folder selection order/MP3 file playback order (Example) CAUTION Attempting to play a file not in the MP3 format which has the “.mp3” file name may produce noise Root folder (Root directory) from the speakers and speaker damage, and can damage your hearing.
Page 523 Comfort controls To fast forward/reverse the disc To select a desired folder (MP3 CDs only) To fast forward or fast reverse the disc, press the fast-forward You can select your desired folder by turning the FOLDER button (11) or the fast-reverse button (10). switch (17).
Page 524 Comfort controls To select a desired track To repeat songs in the same folder (MP3 CDs only) While a song is playing, press the RPT button (8) for 2 seconds You can select your desired track by using the TRACK button or longer (until you hear a beep).
Page 525 Comfort controls To change the order of tracks for playback Random playback for all folders on a disc (MP3 CDs only) Press the RDM button (9) for 2 seconds or longer (until you Random playback for a disc (music CDs only) hear a beep).
Page 526 Comfort controls To find the start of each track on a disc for playback Press the SCAN button (14). “SCAN” will appear on the dis- play and the autochanger will play back the first 10 seconds of each track on the selected disc. The track number will blink while the scan mode is selected.
Page 527 Comfort controls MP3 title ID3 tag information The autochanger can display folder and track titles for discs The autochanger can display ID3 tag information for files that with converted folder and track information. Press the DISP have been recorded with ID3 tag information. button (7) repeatedly to make selections in the following 1.
Page 528 Comfort controls To play tracks from USB device (if so equipped) N00762200030 You can connect your iPod or USB memory device to the USB input terminal and play music files stored in the iPod or USB memory device. See the following section for the types of connectable devices and supported files.
Page 529 Comfort controls iPod control panel and display N00762300028 15- RPT/RDM/D-RDM indicator 1- RADIO button 2- CD (Mode change) button 3- PWR (On-Off) button 4- PAGE (Title scroll) button 5- DISP (Title display) button 6- RPT (Repeat) button 7- RDM (Random) button (Fast-reverse) button (Fast-forward) button 10- DISC UP button...
Page 530 Comfort controls To play from an iPod 5. To stop the playback, press the RADIO button (1) or CD button (2) to switch to a different mode. N00762400032 1. Press the PWR button (3) to turn on the audio system. The NOTE system turns on in the last mode used.
Page 531 Comfort controls To select a desired track To find a track from the iPod menu N00762600018 N00762700022 Press the TRACK button (12) to select the desired track num- You can select desired tracks from the “Playlists”, “Artists”, ber. ® “Albums”, “Songs” or “Genre” (vehicles with Bluetooth interface) menus on your iPod.
Page 532 Comfort controls To play the same track repeatedly To switch the display N00762800010 N00763100010 Press the RPT button (6) during playback to show “RPT” in the You can display the track titles, artist names and album titles display. recorded in the iPod. To exit this mode, press the button again.
Page 533 Comfort controls To play iPod tracks via voice operation (vehicles Preparation for voice operation ® N00763300025 with Bluetooth 2.0 interface) To use the voice operation, press the SPEECH button (1) first. N00763200024 Desired tracks can be selected and played from your iPod by Type 1 “Artist”, “Album”, “Playlist”...
Page 534 Comfort controls To search by artist name 5. If there are two or more matches, the voice guide will say “More than one match was found, would you like to play N00763400026 1. Say “Play” on the main menu. <artist name>?” If you say “Yes,” the system proceeds to step 6.
Page 535 Comfort controls To search by album title 6. After the voice guide says “Playing <album title>,” the system creates a playlist index for the album title. N00763500027 1. Say “Play” on the main menu. NOTE NOTE If the confirmation function is active, the voice guide con- ®...
Page 536 Comfort controls To search by playlist 5. If there are two or more matches, the voice guide will say “More than one match was found, would you like to play N00763600028 1. Say “Play” on the main menu. <playlist>?” If you say “Yes,” the system proceeds to step 6.
Page 537 Comfort controls To search by genre 6. After the voice guide says “Playing <genre>,” the system creates an index for the genre. N00763700029 1. Say “Play” on the main menu. NOTE NOTE If the confirmation function is active, the voice guide con- ®...
Page 538 Comfort controls USB control panel and display N00763900021 15- FOLDER indicator 1- RADIO button 16- TRACK indicator 2- CD (Mode change) button 17- RPT/D-RPT/RDM/D-RDM/SCAN/F-SCAN indicator 3- PWR (On-Off) button 4- PAGE (Title scroll) button 5- DISP (Title display) button 6- RPT (Repeat) button 7- RDM (Random) button (Fast-reverse) button (Fast-forward) button...
Page 539 Comfort controls To play from a USB memory device 5. To stop the playback, press the RADIO button (1) or CD button (2) to switch to a different mode. N00764000032 1. Press the PWR button (3) to turn on the audio system. The NOTE system turns on in the last mode used.
Page 540 Comfort controls Folder selection order/file playback order (example) NOTE The folder and file hierarchy in the USB memory device is If a file protected by copyrights is played, the file will be shown below. skipped. To fast-forward/reverse the track N00764200018 Root folder (Root directory) To fast-forward/reverse the current track, press the button...
Page 541 Comfort controls To select a file To find a track N00764300019 N00764400078 Press the TRACK button (13) to select the desired file number. You can select a folder to find a desired track. 1. Turn the FOLDER switch (12) to show the desired folder : The file number increases by one.
Page 542 Comfort controls To play the same file repeatedly To find the start of each track in a folder for playback ® N00764500011 (vehicles without Bluetooth 2.0 interface) Press the RPT button (6) to show “RPT” in the display. To can- N00764900073 cel this mode, press the button again.
Page 543 Comfort controls To switch the display NOTE Once the cueing playback ends, playback will start from N00765100014 You can display titles with tag information. the track at the beginning of the folder next to the one that was playing when the cueing started. Folder title The display changes as follows every time the DISP button (5) is pressed during playback.
Page 544 Comfort controls To play USB memory device tracks via voice NOTE Press and hold the DISP button (5) again until you hear a ® operation (vehicles with Bluetooth 2.0 interface) beep, and the tag information display returns to the folder N00765200031 title display.
Page 545 Comfort controls ® Preparation for voice operation To play tracks from a Bluetooth device To use the voice operation, press the SPEECH button (1) first. ® (vehicles with Bluetooth 2.0 interface) Type 1 N00765300087 You can wirelessly connect a digital audio player or cellular ®...
Page 546 Comfort controls ® Bluetooth device control panel and display N00765400020 1- CD (Mode change) button 2- PWR (On-Off) button 3- PAGE (Title scroll) button 4- DISP (Title display) button 5- RPT (Repeat) button 6- RDM (Random) button 7- DISC DOWN (Pause/Stop) button 8- DISC UP (Play) button 9- SCAN button 10- TRACK (Track up/down) button...
Page 547 Comfort controls To listen to tracks from a device connected via To pause the playback (if supported by the device) ® N00765700010 Bluetooth To pause the playback, press the DISC DOWN button (7). To restart the playback, press the DISC UP button (8). N00765500034 1.
Page 548 Comfort controls To play tracks in random order (if supported by the 2. The display changes as follows every time the DISP but- device) ton (4) is pressed briefly: Album title → Title name → Artist name → Genre N00766000010 Press the RDM button (6) to show “RDM”...
Page 549: To Use The External Audio Input Function
NOTE For information on using the video input connector (C), refer to the separate owner’s manual for a Mitsubishi Multi-Communication System. I n f o r ma t i o n P r o v i d e d b y :...
Page 550 Comfort controls To activate the external audio input mode NOTE The connected audio equipment cannot be operated with the vehicle’s audio system. Depending on the connected audio equipment, it may pro- duce noise from the speakers. Use the connected audio equipment’s own power source, such as its battery.
Page 551: Steering Wheel Audio Remote Control Switch
Comfort controls Steering wheel audio remote control switch Type 2 (if so equipped) N00714800426 The remote control switch is located on the left side of the steering wheel. The switch can be operated when the ignition switch is in either the “ON” or “ACC” position. Type 1 1- Volume up button 2- Volume down button...
Page 552: Volume Control
Comfort controls Channel selection / Category selection (Vehicles with To turn on the power satellite radio) Press the power switch (3) to turn on the power. When the power is turned on, the last mode used before turning off is dis- Seek up button - 4 / Seek down button - 5 played.
Page 553 Comfort controls To listen to a USB memory device To select a desired track You can select your desired track by using the track up button Press the mode selector button (3) and select USB mode. (4) or the track down button (5). To select a desired file NOTE File up button - 4...
Page 554: Error Codes
ERROR 03 Mechanism error tion. Mitsubishi Motors dealer or a repair facility of your choice for repair. I n f o r ma t i o n P r o v i d e d b y : 5-137...
Page 555 Bring your vehicle to your authorized Communication or ERROR and audio equipment. Mitsubishi Motors dealer or a repair facility of power supply error Power supply error of external device. your choice for repair. I n f o r ma t i o n P r o v i d e d b y :...
Page 556 Take the vehicle to your authorized The antenna may be faulty, not securely ANTENNA ↔ ERROR Antenna error Mitsubishi Motors dealer or a repair connected, or open-circuited. facility of your choice. Move to a place where the signal is ACQUIRING Cannot pick up signal.
Page 557 Take the vehicle to your authorized Mechanical fault or bad There is a mechanical fault or a bad con- SAT ERROR Mitsubishi Motors dealer or a repair connection nection. facility of your choice. This channel is not broadcasting at the...
Page 558 Remove the iPod. An overcurrent or other power-supply error has USB BUS PWR (Blink) Have the vehicle inspected at an authorized Mitsubishi occurred. Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 559 If this error is displayed again, have the vehicle communication error. inspected at an authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 560 Comfort controls Error codes (USB memory device) N00766400014 If an error code (1) appears in the display, take action in accordance with the table below. Error display Item Repair Record music files in the format supported by the U NO SONG There are no playable music files.
Page 561 An overcurrent or other power-supply error Have the vehicle inspected at an authorized USB BUS PWR (Blink) has occurred. Mitsubishi Motors dealer or a repair facility of your choice. Have the vehicle inspected at an authorized U LSI ERROR (Blink)
Page 562 Comfort controls Handling of compact discs (CD) N00734100311 Use only compact discs that have the following mark. (Playback of CD-R or CD-RW discs may cause prob- lems.) The use of special shaped compact discs, damaged com- pact discs (like cracked discs) or low-quality compact discs (like warped discs or burrs on the discs) such as those shown will damage the CD player.
Page 563 Comfort controls In the following circumstances, moisture can form on To clean a disc, use a soft, clean, dry cloth. Wipe directly discs and inside the audio system, preventing normal from the center hole toward the outer edge. Do not wipe in operation.
Page 564 CD player by yourself. There are no user serviceable parts inside. In case of malfunction, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 565: Satellite Radio
Comfort controls Antenna Roof antenna (for vehicles with SIRIUS satellite radio) N00734200426 For securing the best satellite reception, the angle of the Roof antenna (except for vehicles with SIRIUS antenna is fixed. satellite radio) To remove Turn the pole (A) counterclockwise. To install Screw the pole (A) clockwise into the base (B) until it is securely retained.
Page 566 Comfort controls Digital clock To remove (if so equipped) Turn the pole (A) counterclockwise. N00755000094 The time is displayed when the ignition switch is in the “ON” To install or “ACC” position. Screw the pole (A) clockwise into the base (B) until it is To set the time securely retained.
Page 567 Comfort controls General information about your radio — Time signal setting At the same time the button is pressed, the fol- N00733900383 lowing modifications are made. Your vehicle’s radio receives both AM and FM stations. 10:00 - 10:29 ..Change to 10:00 The quality of your reception is affected by distance, obstacles, 10:30 - 10:59 ..Change to 11:00 and signal interference.
Page 568 Comfort controls Signal transmission Reflection FM signals do not follow the earth surface nor are they The reason why one can hear FM but not AM in parking reflected by the upper atmosphere. For this reason, FM broad- garages, under bridges etc., is that FM signals, unlike AM sig- casts cannot be received over long distances.
Page 569 Comfort controls Cross modulation Causes of disturbances If one listens to a weak station and is in the vicinity of another FM reception is affected by the electrical systems of vehicles in strong station, both stations might be received simultaneously. the vicinity, especially those without an electronic noise sup- pression device.
Page 570 I n f o r ma t i o n P r o v i d e d b y :...
Page 571 I n f o r ma t i o n P r o v i d e d b y :...
Page 572: For Emergencies
For emergencies If the vehicle breaks down ....6- Jump-starting the engine ....6- Engine overheating .
Page 573: If The Vehicle Breaks Down
For emergencies If the vehicle breaks down Jump-starting the engine N00836300161 N00836400713 If your vehicle breaks down on the road, move to the shoulder If the engine cannot be started because the battery is weak or and turn on the hazard warning flashers. If there is no shoulder, dead, you can start it with the battery from another vehicle or the shoulder is not safe, drive in the right lane slowly, with using jumper cables.
Page 574 For emergencies 3. You could be injured if the vehicles move. Set the parking 5. For vehicles equipped with turbocharger, remove the air brake firmly on each vehicle. Put an automatic transaxle, duct and then the battery upper cover. CVT or Twin Clutch SST in “P” (PARK) or a manual (Refer to “Removing and installing the battery upper transaxle in “N”...
Page 575 For emergencies 7. Connect one end of the other jumper cable to the negative 9. After the engine is started, disconnect the cables in the (-) terminal of the booster battery (B), and the other end to reverse order from the way you connected them. the engine block of the vehicle with the low battery (A) at 10.
Page 576: Engine Overheating
3. Check that the cooling fan is running. If the fan is not turning, stop the engine immediately and contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for assistance. WARNING To avoid personal injury, keep hands, hair, jewelry and clothes away from the cooling fan.
Page 577 11. Have your vehicle checked by your authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 578 For emergencies Tools and jack Tools N00832600124 N00836600265 Storage The tools and jack are stowed in the trunk. 1- Tool bag 2- Bar 3- Wheel nut wrench 1- Tools 2- Jack I n f o r ma t i o n P r o v i d e d b y :...
Page 579 For emergencies Jack To remove N00832700255 Turn the shaft end (1) so that the jack contracts, then remove it Before removing the jack, lift up the luggage floor board. from the storage bracket (C). For front-wheel drive vehicles, pull the luggage floor board (A) rearward to release the hooks (B), and then lift it up.
Page 580: How To Change A Tire
For emergencies How to change a tire 5. To prevent the vehicle from rolling when it is raised on the jack, place chocks or blocks (A) at the tire that is diago- N00836900734 nally opposite from the tire (B) you are changing. WARNING The jack should not be used for any purpose other than to change a tire.
Page 581 Refer to “Tools and jack” on page 6-7. the tire pressure monitoring system will not function Spare tire information properly. Have the tire replaced or repaired at an authorized Mitsubishi Motors dealer or a repair N00849600298 facility of your choice as soon as possible. Compact spare tire If your vehicle has aluminum type wheels, you can The compact spare tire is designed to save space in the trunk.
Page 582 For emergencies To remove the compact spare tire CAUTION N00849700228 Do not drive through automatic car washes and over 1. Lift up the luggage floor board. obstacles that could possibly damage the underside For front-wheel drive vehicles, pull the luggage floor of your vehicle.
Page 583 For emergencies NOTE 2. To remove the spare tire, remove the installation clamp Put the spare tire under the vehicle body near the jack. (C) by turning it counterclockwise. This makes it safer if the jack slips out of position. NOTE The clamp cannot be used for a normal size tire.
Page 584 For emergencies To change a tire 2. Place the jack under one of the jacking points (A) shown in the illustration. Use the jacking point closest to the tire N00849800388 1. On vehicles with wheel covers, first remove the covers you wish to change.
Page 585 For emergencies 3. Rotate the jack by hand until the flange portion (B) fits in 4. Insert the bar (D) into the wheel nut wrench (E). Then put the groove (C) at the top of the jack. the end of the bar into the shaft’s jack end, as shown in the illustration.
Page 586 For emergencies 6. Clean out any mud, etc. on the hub surface (F), hub bolts WARNING (G) or in the installation holes (H) in the wheel, and then The jack should not be used for any purpose other mount the spare tire. than to change a tire.
Page 587 For emergencies 7. [Vehicle with steel wheels] WARNING • Normal wheels and compact spare wheel Mount the spare wheel with the valve stem (I) facing Install the wheel nuts (tapered nuts) with their tapered outboard. If you cannot see the valve stem (I), you ends facing inward, then tighten by hand until the wheel is have installed the wheel backwards.
Page 588 For emergencies [Vehicle with aluminum wheels] • Compact spare wheel • Normal wheels Install the wheel nuts with their tapered ends facing Temporarily tighten the wheel nuts (flange nuts) until inward, then tighten by hand until the wheel is no longer their flange section comes in contact with the wheel and it loose.
Page 589 For emergencies 8. Lower the vehicle slowly by rotating the wheel nut 9. Tighten the nuts in the order shown in the illustration until wrench counterclockwise until the tire touches the each nut has been tightened to the torque listed here. ground.
Page 590 Mitsubishi Motors dealer Refer to “Tire inflation pressures” on page 7-32. or a repair facility of your choice.
Page 591 For emergencies Wheel covers To install (if so equipped) N00849400209 CAUTION To remove Wrap the tip of the bar with a cloth, insert it deeply into the Before installing the wheel cover to the wheel, make notch provided in the wheel cover, and pry the cover away sure that the tabs (A) on the back of the wheel cover from the wheel.
Page 592 For emergencies 1. Align the tire air valve (C) and the wheel cover notch (D). 2. Push the bottom (F) of the wheel cover into the wheel. 3. Gently push in both sides (G) of the wheel cover and hold them in place with both knees.
Page 593 For emergencies Towing Type A N00837000862 If your vehicle needs to be towed If towing is necessary, we recommend you to have it done by a commercial tow truck service. When towing is required, transport the vehicle using a tow truck.
Page 594 For emergencies Towing the vehicle by a tow truck CAUTION [For front-wheel drive vehicle equipped with the CAUTION active stability control (ASC)] This vehicle must not be towed by a tow truck using If the vehicle is towed with the ignition switch in the sling lift type equipment (Type A) as illustrated.
Page 595: Operation Under Adverse Driving Conditions
For emergencies Operation under adverse driving conditions Towing with front wheels off the ground (Type C) Release the parking brake. N00837200662 Place the gearshift lever in the “Neutral” position (manual tran- If your vehicle becomes stuck in sand, mud or saxle) or the selector lever in the “N”...
Page 596 For emergencies On wet roads On snowy or icy roads When driving on a road covered with snow or ice, use CAUTION snow tires. Tire chains cannot be used on your vehicle. There may be state or local regulations about using snow Avoid flooded roads.
Page 597 For emergencies On a bumpy or rutted road Drive as slow as possible when driving on bumpy or rut- ted roads or over potholes etc. CAUTION Driving on bumpy, rutted roads or over potholes can damage the tires and wheels. Wheels with low-profiles tires or under-inflated tires are especially at risk for damage.
Page 598: Vehicle Care And Maintenance
Vehicle care and maintenance Brake pedal free play..... . . 7- 38 Service precautions ......7- Catalytic converter .
Page 599: Service Precautions
If you discover a malfunction or other problem, have it cor- wrong way can injure you. Ask an authorized rected by an authorized Mitsubishi Motors dealer or a repair Mitsubishi Motors dealer or a repair facility of your facility of your choice.
Page 600: Catalytic Converter
Have an inspection made Do not park or run your vehicle in areas where com- by an authorized Mitsubishi Motors dealer or a repair bustible materials such as dry grass or leaves can facility of your choice as soon as possible.
Page 601: Engine Hood
Vehicle care and maintenance Engine hood To open Use the engine hood release lever (located under the instrument N00937500464 panel near the driver’s door) to unlock the engine hood. CAUTION Pull the lever toward you to release the engine hood latch. For vehicles with turbocharger, to avoid the risk of being burned, do not touch the air outlet (A) and air scoop (B) on the engine hood when the engine com-...
Page 602 Vehicle care and maintenance Release the safety lever and lift the engine hood. Support the engine hood with the hood prop. Insert the hood prop securely in the opening under the hood marked with an arrow. NOTE To prevent damage to the engine hood and wipers, make sure the wipers are at resting position when you open the CAUTION engine hood.
Page 603 Vehicle care and maintenance To close NOTE If this does not close the engine hood properly, drop it Unlatch the prop from the engine hood and put it back in its again from a slightly higher position. retainer. Do not push down strongly on the engine hood. Depend- ing on how strongly or where you push down, you could create a dent in the vehicle body.
Page 604: View Of The Engine Compartment
Vehicle care and maintenance View of the engine compartment Vehicles with turbocharger N00937600667 Except for vehicles with turbocharger 1- Power steering fluid reservoir (if so equipped) 2- Air cleaner filter 3- Brake fluid/Clutch fluid reservoir (if so equipped) 4- Engine coolant reservoir 5- Windshield washer fluid reservoir 6- Engine oil level dipstick 7- Radiator cap...
Page 605: Engine Oil And Oil Filter
Vehicle care and maintenance Engine oil and oil filter Except for vehicles with turbocharger N00937700860 Except for vehicles with engine cover To check and refill engine oil It is normal for an engine to use oil. You may need to add oil between the recommended oil change intervals.
Page 606 Vehicle care and maintenance Vehicles with turbocharger WARNING Used engine oil is poisonous, and can damage your skin. Prolonged and repeated contact may cause serious skin disorders, including dermatitis and can- cer. Don’t let used oil touch your skin. Wash thor- Good oughly after working with it.
Page 607 If you cannot find oils with the ILSAC certification symbol, use an API classification SM or higher oil with the following Mitsubishi Motors recommends using only engine oils with the label. ILSAC certification symbol on the front of the container.
Page 608 Vehicle care and maintenance Recommended engine oil viscosity Vehicles with turbocharger N00955000070 Use engine oil with the proper thickness for the outdoor tem- peratures where you will be driving. Except for vehicles with turbocharger NOTE Select engine oil of the proper SAE viscosity number according to the atmospheric temperature.
Page 609: Engine Coolant
256 psi remove the radiator cap (B) except when you check the coolant (1.8 MPa). A Genuine Mitsubishi oil filter is the best replace- freeze point or replace the antifreeze coolant.
Page 610 If you need to add coolant often, or if the level in the reserve tank does not drop when the engine cools, the cooling system should be pressure-tested for leaks. Take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice for testing. Vehicles with turbocharger...
Page 611: Radiator Cap
Do not use water to adjust the concentration of cool- rized Mitsubishi Motors dealer or a repair facility of your ant. choice to have the thermostat checked, and replaced if Do not top off the tank with plain water only.
Page 612: Air Cleaner Filter
Vehicle care and maintenance Air cleaner filter 1. Remove the clips (A), then remove the duct (B). N00937900396 The air cleaner filter will get dirty and dusty from use and not Except for vehicles with turbocharger filter properly. Replace it with a new filter using the schedule in the “WARRANTY AND MAINTENANCE MANUAL”.
Page 613 Vehicle care and maintenance 2. Except for vehicles with turbocharger, while holding 3. Unclamp and take out the air cleaner filter. down the tab (C), pull out the connector (D). Type 1 Except for vehicles with turbocharger Type 2 I n f o r ma t i o n P r o v i d e d b y : 7-16...
Page 614 4. Install the air cleaner filter and put the cover back on in its Vehicles with turbocharger original position. NOTE Genuine Mitsubishi Motors Parts are recommended when replacing the air cleaner filter. After replacing the air cleaner filter, make sure that the hinges at the bottom of cover are firmly set.
Page 615: Manual Transaxle Oil (If So Equipped)
The continuously variable transmission (CVT) should be main- Refill or change the oil according to the table. tained and serviced by an authorized Mitsubishi Motors dealer or a repair facility of your choice to obtain the best perfor- Oil type mance and longest life.
Page 616: Twin Clutch Sportronic Shift Transmission
The Twin Clutch Sportronic shift transmission (Twin Clutch the table. SST) should be maintained and serviced by an authorized Mitsubishi Motors dealer or a repair facility of your choice to Oil type obtain the best performance and longest life. It is important that the transmission fluid is kept at the correct level.
Page 617: Rear Axle Oil (All-Wheel Drive Models)
Vehicle care and maintenance Rear axle oil (All-wheel drive models) AWC control fluid (if so equipped) N00915200155 N00915300026 Whenever the oil level is checked, add oil as necessary to To check the fluid level maintain the proper level. Remove the lid on the trunk room right side trim. Fill or change oil according to the table.
Page 618: Washer Fluid
If this occurs, have the vehicle checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice. I n f o r ma t i o n P r o v i d e d b y :...
Page 619: Power Steering Fluid (If So Equipped)
Keep the reservoir tank cap closed to keep the brake fluid from evaporating. Fluid type Lubricant Genuine Mitsubishi Power Steering Fluid I n f o r ma t i o n P r o v i d e d b y : 7-22...
Page 620 Vehicle care and maintenance Battery To remove 1. Remove the clips (A), and then remove the air duct (B). N00939100783 The condition of the battery is very important for quick starting and to keep the vehicle’s electrical system working properly. Check the battery regularly.
Page 621 Vehicle care and maintenance To install 2. Turn the plastic nuts (C) counterclockwise, and then remove the battery upper cover (D). 1. Install the battery upper cover (A) onto the battery, and then push the plastic nuts (B) in the direction shown by the arrows to secure the cover.
Page 622: To Check The Battery Indicator
Vehicles with turbocharger battery and charging system tested by an authorized Mitsubishi Motors dealer or a repair facility of your choice. If it is white, that cell is low on charge and the battery may only need charg- ing.
Page 623: During Cold Weather
Vehicle care and maintenance NOTE Vehicles with turbocharger For vehicles equipped with a turbocharger, the battery upper cover must be removed to check the battery indica- tor. Checking battery electrolyte level N00901500014 The electrolyte level must be between the limits shown on the outside of the battery.
Page 624: Disconnection And Connection
(+) terminal of the battery. It is recommended that you have your battery and charging sys- tem checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice before the start of cold weather. If necessary, have it charged.
Page 625 If the electrolyte level is very low, have the battery Never short-circuit the battery. This could cause it checked at an authorized Mitsubishi Motors dealer to overheat and be damaged. or a repair facility of your choice. Keep sparks, cigarettes, and flames away from the Battery terminals and related accessories contain battery because the battery could explode.
Page 626 Vehicle care and maintenance Tires Intended outboard sidewall: • The sidewall that contains a whitewall, bears white let- N00939200481 tering or bears manufacturer, brand, and/or model name WARNING molding that is higher or deeper than the same molding on the other sidewall of the tire, Driving with tires that are worn, damaged or improperly inflated is dangerous.
Page 627: Tire Markings
Vehicle care and maintenance Cord: the strands forming the plies in the tire. Size Designation Rim: a metal support for a tire or a tire and tube assembly upon which the tire beads are seated. EXAMPLE:P215/65R15 Rim diameter: nominal diameter of the bead seat. Passenger car tire size based on U.S.A.
Page 628 Vehicle care and maintenance Service Description Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire but EXAMPLE: 95H the date code may only be on one side. Look for the TIN on the outboard side of tires as mounted on the vehicle.
Page 629: Tire Inflation Pressures
Vehicle care and maintenance Tire inflation pressures Treadwear, Traction and Temperature Grades N00939300844 Treadwear Proper tire inflation pressure is essential for the safe and satis- The treadwear grade is a comparative rating based on the factory operation of your vehicle. The wrong tire pressure will wear rate of the tire when tested under controlled conditions cause problems in three major areas: on a specified government test course.
Page 630 Vehicle care and maintenance The recommended inflation pressures should be used for the tire inflation pressure may increase 14 to 41 KPA, 2 to 6 PSI tires listed below. from the cold inflation pressure. Do not let air out of the tires to get back to the specified cold pressure, or your tire pressure Except for vehicles with turbocharger will be too low.
Page 631: Tire Maintenance
Consult an authorized Mitsubishi Motors dealer or a repair facility of your choice before using wheels that you have. Only Mitsubishi Motors genuine wheels should be used, because your vehicle is equipped with a tire pressure monitoring system.
Page 632: Tire Rotation
Abnormal wear is usually caused by a wrong tire pressure, wheels that are not aligned properly, wheels that are out-of-balance, or severe braking. Check with an authorized Mitsubishi Motors dealer or a repair facility of your choice to find out the reason for uneven tread wear.
Page 633 Vehicle care and maintenance CAUTION Tires that do not have arrows showing rotation direction If the tires have arrows (A) indicating the correct direction of rotation, swap the front and rear tires on the left-hand side of the vehicle and the front and Front rear tires on the right-hand side of the vehicle sepa- rately.
Page 634: Tire Chains
If flange nuts are used on your vehicle, change to tapered nuts when using snow tires with steel wheels. CAUTION Only Mitsubishi Motors genuine wheels should be used, because your vehicle is equipped with a tire Avoid the combined use of different types of tires. pressure monitoring system.
Page 635: Clutch Pedal Free Play (If So Equipped)
.1 to .3 inch (3 to 8 mm) If the free play is not within these limits, take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice for adjustment. I n f o r ma t i o n P r o v i d e d b y :...
Page 636: Parking Brake Lever Stroke
Parking brake lever stroke: This procedure is described in the vehicle service manual and 3 to 5 notches can be carried out by an authorized Mitsubishi Motors dealer. Also check to see if the lever stays gripped by the ratchet after pulling.
Page 637: Emission-Control System Maintenance
To be sure the emission-control system works properly, have your vehicle inspected and maintained by an authorized Mitsubishi Motors dealer or a repair facility of your choice fol- lowing the schedule in the “WARRANTY AND MAINTE- NANCE MANUAL”.
Page 638: Spark Plugs
Vehicle care and maintenance Spark plugs NOTE To meet government regulations and promote cleaner air, N00940900215 Spark plugs must fire properly for good engine performance your vehicle is equipped with an onboard diagnostic sys- and emission-control. tem (OBD). The engine electronic control module that Do not reuse them by cleaning or regapping.
Page 639 Check all the hose connections, such Have the system checked at an authorized Mitsubishi Motors as clamps and couplings, to make sure they are secure and that dealer at the mileage specified in the “WARRANTY AND there are no leaks.
Page 640: General Maintenance
But, if any of these parts stops working properly, your vehicle performance could suffer. Have these items checked if you notice a problem with them. See your authorized Mitsubishi Motors dealer for assistance, if you have any questions. Disc brake pads, rear drum brake linings and...
Page 641: Exhaust System
Vehicle care and maintenance Exhaust system Hood lock release mechanism and safety catch N00942200108 N00942500114 The hood lock release mechanism and hood safety catch should WARNING be checked, cleaned, and oiled when needed for easy move- ment and to stop rust and wear. Use Multipurpose Grease Carbon monoxide gas from your vehicle’s exhaust is NLGI Grade 2 sparingly for all sliding parts of the hood latch poisonous.
Page 642: For Cold And Snowy Weather
The ventilation slots in front of the windshield should be In case of a melted fusible link, see your authorized Mitsubishi brushed clear after a heavy snowfall so that the operation of the Motors dealer or a repair facility of your choice for inspection heating and ventilation systems will not be impaired.
Page 643 Vehicle care and maintenance Fuses 1. Open the fuse lid and pull to remove it. N00942800801 Fuse block location To prevent damage to the electrical system from short-circuit- ing or overloading, each individual circuit is equipped with a fuse. The fuse blocks are located in the passenger compartment and in the engine compartment.
Page 644 Vehicle care and maintenance 2. For vehicles with the bottom cover, use the puller to WARNING loosen the 2 clips (A) and push down the bottom cover. When changing fuses, do not damage the driver’s The puller is in the fuse block in the engine compartment. knee airbag harness or accidentally strike the airbag Refer to “Fuse replacement”...
Page 645 Vehicle care and maintenance Engine compartment 3. To put back the fuse lid, line up the fuse lid hook (B) with the clamp (C) on the instrument panel and push the lid In the engine compartment, the fuse block is located as shown back in.
Page 646 Vehicle care and maintenance Passenger compartment fuse location table Symbol Electrical system Capacity Passenger compartment fuse location Heater 30 A* Stop lights 15 A (Brake lights) Rear fog light 10 A Main fuse block Sub fuse block Windshield wiper 30 A Optional 10 A Door locks...
Page 647 Vehicle care and maintenance Engine compartment fuse location table Symbol Electrical system Capacity Accessory socket 15 A Engine compartment fuse location Power window control 30 A* Defogger 30 A* Heated 7.5 A outside rearview mirrors 115V Power outlet 15 A Power seats 25 (20) A Heated seats...
Page 648 Vehicle care and maintenance Symbol Electrical system Capacity Symbol Electrical system Capacity Headlight Front fog lights 15 A (low/high Discharge 20 A Engine 7.5 A beam) (left) Headlight Automatic transaxle 20 A (low/high Discharge 20 A Horn 10 A beam) (right) Alternator 7.5 A Headlight...
Page 649 Vehicle care and maintenance Some fuses may not be installed on your vehicle, depend- Symbol Electrical system Capacity ing on the vehicle model or specifications. Except for The table above shows the main equipment corresponding vehicles with 15 A to each fuse. turbocharger Fuel pump There are no 7.5 A, 25 A or 30 A spare fuses.
Page 650: Fuse Replacement
Vehicle care and maintenance Fuse replacement 3. Clamp it on the fuse you wish to remove, and pull the fuse straight out from the fuse block. N00954900027 1. Before replacing a fuse, always turn off the electrical item connected to the fuse and turn the ignition switch to the “LOCK”...
Page 651 CAUTION Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the problem checked. Never use a fuse with a capacity greater than the one listed or any substitute, such as wire, foil etc.
Page 652: Replacement Of Light Bulbs
If you are unsure of how to carry out the work as required, it is recommended that these procedures be carried out by an authorized Mitsubishi Motors dealer or a repair facility of your choice. Be careful not to scratch the vehicle body when removing a light and lens.
Page 653 It is not possible to repair or replace only the bulb for the 6- Side turn signal light — side turn-signal light. Check with an authorized Mitsubishi Motors dealer or a [For vehicles with high intensity discharge headlights] repair facility of your choice when the light needs to be ANSI Trade repaired or replaced.
Page 654 Vehicle care and maintenance NOTE Rear The high-mounted stop light uses LEDs rather than bulbs. For repair and replacement, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice. ANSI Trade Description Wattage No. or Bulb type High-mounted stop —...
Page 655 Vehicle care and maintenance Headlights (low beam, except for vehicles with Inside high intensity discharge headlights) N00950400460 N00943100872 1. For vehicles equipped with turbocharger, when replacing the bulb on the driver’s side, remove the bolt (A) holding down the relay box and move the relay box toward the rear of the vehicle.
Page 656 Vehicle care and maintenance 2. For vehicles equipped with turbocharger, when replacing 3. Turn the bulb (C) counterclockwise, and then remove the the bulb on the passenger’s side, lift up the engine coolant headlight bulb with holder. reservoir (B). *- Front of the vehicle *- Front of the vehicle I n f o r ma t i o n P r o v i d e d b y : 7-59...
Page 657 Vehicle care and maintenance 4. While holding down the tab (D), pull out the bulb (E). CAUTION Handle halogen light bulb with care. The gas inside a halogen light bulb is highly pressurized, so drop- ping, knocking, or scratching a halogen light bulb can cause it to shatter.
Page 658 Vehicle care and maintenance Headlights (high beam, except for vehicles with 2. Turn the cap (B) counterclockwise to remove it. high intensity discharge headlights) N00943100885 1. When replacing the bulb on the front passenger’s side, remove the bolt (A) holding down the washer tank spout and move the spout toward the rear of the vehicle.
Page 659 Vehicle care and maintenance 3. Turn the bulb (C) counterclockwise to remove it. 4. While holding down the tab (D), pull out the bulb (E). 5. To install the bulb, perform the removal steps in reverse. *- Front of the vehicle I n f o r ma t i o n P r o v i d e d b y : 7-62...
Page 660 Vehicle care and maintenance Daytime running lights (for vehicles with high CAUTION intensity discharge headlights) Handle halogen light bulb with care. The gas inside N00900300103 a halogen light bulb is highly pressurized, so drop- 1. When replacing the bulb on the front passenger’s side, ping, knocking, or scratching a halogen light bulb remove the bolt (A) holding down the washer tank spout can cause it to shatter.
Page 661 Vehicle care and maintenance 2. Turn the cap (B) counterclockwise to remove it. 3. Turn the socket (C) counterclockwise to remove it. *- Front of the vehicle *- Front of the vehicle I n f o r ma t i o n P r o v i d e d b y : 7-64...
Page 662 Adjustment of headlight aim N00943200121 The alignment of the headlights should be checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice. 5. To install a bulb, perform the removal steps in reverse. I n f o r ma t i o n P r o v i d e d b y :...
Page 663 Vehicle care and maintenance Parking and side-marker lights (except for vehi- 2. For vehicles equipped with turbocharger, when replacing cles with high intensity discharge headlights) the bulb on the passenger’s side, lift up the engine coolant reservoir (B). N00917300512 1. For vehicles equipped with turbocharger, when replacing the bulb on the driver’s side, remove the bolt (A) holding down the relay box and move the relay box toward the rear of the vehicle.
Page 664 Vehicle care and maintenance 3. Turn the socket (C) counterclockwise to remove it. 4. Pull the bulb out of the socket. 5. To install the bulb, perform the removal steps in reverse. *- Front of the vehicle I n f o r ma t i o n P r o v i d e d b y : 7-67...
Page 665 Vehicle care and maintenance Parking and side-marker lights (for vehicles with Type 2 high intensity discharge headlights) N00917300538 1. To create enough work space, turn the steering wheel all the way in the direction opposite to the side you wish to replace.
Page 666 Vehicle care and maintenance 3. Turn the socket (D) counterclockwise to remove it. 5. To install the bulb, perform the removal steps in reverse. 4. Pull the bulb out of the socket. I n f o r ma t i o n P r o v i d e d b y : 7-69...
Page 667: Front Turn Signal Lights
Vehicle care and maintenance Front turn signal lights Vehicles with turbocharger N00943400325 1. Remove the clips (A) and clips (B), then remove the duct (C) and the upper cover (D). Except for vehicles with turbocharger I n f o r ma t i o n P r o v i d e d b y : 7-70...
Page 668 Vehicle care and maintenance 2. Remove the entire socket and bulb assembly (E) by turn- 3. Remove the bulb by pulling it out. ing it counterclockwise. 4. To install the bulb, perform the removal steps in reverse. *- Front of the vehicle I n f o r ma t i o n P r o v i d e d b y : 7-71...
Page 669 Vehicle care and maintenance Front fog lights (Type 1) (if so equipped) 2. Remove the screws (B) and pull the entire light unit out. N00943600734 1. Remove the screw (A) and pull the cover out. I n f o r ma t i o n P r o v i d e d b y : 7-72...
Page 670 Vehicle care and maintenance NOTE 3. Push the connector (D) to disconnect and remove the fog When unfastening the screws, be careful not to mistakenly light. move the beam position adjustment screw (C). I n f o r ma t i o n P r o v i d e d b y : 7-73...
Page 671 Vehicle care and maintenance NOTE 4. Remove the bulb assembly (E) by turning it counterclock- When mounting the cover, align the hooks (F) on the wise. cover with the hole in the body. 5. To install the bulb, perform the removal steps in reverse. I n f o r ma t i o n P r o v i d e d b y : 7-74...
Page 672 Vehicle care and maintenance Front fog lights (Type 2) (if so equipped) CAUTION N00943600747 Handle halogen light bulbs with care. The gas inside 1. Remove the screw (A). a halogen light bulb is highly pressurized, so drop- ping, knocking, or scratching a halogen light bulb can cause it to shatter.
Page 673 Vehicle care and maintenance 2. Pull the cover out in the direction of the arrow shown in 3. Remove the screws (B) and pull the entire light unit out. the illustration. Passenger’s side Driver’s side I n f o r ma t i o n P r o v i d e d b y : 7-76...
Page 674 Vehicle care and maintenance NOTE 4. Push the connector (D) to disconnect and remove the fog When unfastening the screws, be careful not to mistakenly light. move the beam position adjustment screw (C). I n f o r ma t i o n P r o v i d e d b y : 7-77...
Page 675 Vehicle care and maintenance NOTE 5. Remove the bulb assembly (E) by turning it counterclock- When mounting the cover, align the hook (F) on the cover wise. with the hole in the body. 6. To install the bulb, perform the removal steps in reverse. I n f o r ma t i o n P r o v i d e d b y : 7-78...
Page 676: Rear Combination Lights
Vehicle care and maintenance Rear combination lights CAUTION N00943700386 Handle halogen light bulbs with care. The gas inside Tail and stop lights, rear turn signal lights and rear a halogen light bulb is highly pressurized, so drop- side-marker lights ping, knocking, or scratching a halogen light bulb 1.
Page 677 Vehicle care and maintenance 2. Remove the light unit in the rear direction. 3. Remove the socket and bulb assemblies by turning them counterclockwise. B- Tail and stop light C- Rear turn signal light D- Rear side-marker light I n f o r ma t i o n P r o v i d e d b y : 7-80...
Page 678 Vehicle care and maintenance 4. Remove the bulb by pulling it out. 5. To install the bulb, perform the removal steps in reverse. NOTE Tail and stop light and Rear side-marker light When mounting the light unit, align the pins (E) on the Rear turn signal light light unit with the holes in the body.
Page 679 Vehicle care and maintenance Tail lights and back-up lights 2. Remove the socket and bulb assemblies by turning them counterclockwise. 1. Open the trunk lid. Remove the clips (A) and remove the cover (B). C- Tail light D- Back-up light I n f o r ma t i o n P r o v i d e d b y : 7-82...
Page 680: License Plate Light
Vehicle care and maintenance License plate light 3. Remove the bulb by pulling it out. N00944000331 Back-up light Tail light 1. Remove the screws (A) from the license plate light lens (B). Then, remove the lens and gasket (C), and withdraw the bulb.
Page 681 Vehicle care and maintenance 2. Remove the socket and bulb assembly together by turning 3. Remove the bulb by pulling it out. it counterclockwise. 4. To install the bulb, perform the removal steps in reverse. I n f o r ma t i o n P r o v i d e d b y : 7-84...
Page 682 Vehicle care and maintenance Dome light (front)/Reading lights (if so equipped) 2. While holding down the tab (A), pull out the bulb. N00944500206 1. Insert a screwdriver into the notch of the light assembly. Gently pry to remove the lens. 3.
Page 683 Vehicle care and maintenance Dome light (rear) NOTE (if so equipped) Before replacing the bulb, put the dome light (front)/read- N00944100260 ing lights switch into the “OFF” position. 1. Insert a screwdriver into the notch of the light assembly and pry gently to remove the lens. When mounting the lens, align the tab (B) with the hole on the vehicle body.
Page 684 Vehicle care and maintenance NOTE 2. While holding down the tab (A), pull out the bulb. Before replacing the bulb, put the dome light (rear) switch into the “OFF” position. When mounting the lens, align the tab (B) with the hole on the vehicle body.
Page 685: Vehicle Care Precautions
If you are not sure, contact an authorized Mitsubishi Motors dealer for help in choosing these materials. CAUTION Cleaning products can be dangerous. Some are poi- sonous.
Page 686: Cleaning The Inside Of Your Vehicle
Vehicle care and maintenance Cleaning the inside of your vehicle These can all be dangerous, and they all can damage your vehi- cle. N00945200079 After washing the inside of your vehicle with any cleaner, wipe it dry in a shady, well ventilated area. CAUTION Do not use organic substances (solvents, benzine, kerosene, alcohol, gasoline, etc.) or alkaline or acidic...
Page 687 Vehicle care and maintenance NOTE 2. To rinse, dip the cloth in fresh water, wring it out well, and Do not use cleaners, conditioners, and protectants contain- wipe off all the soap. ing silicones or wax. 3. To preserve and protect, use a leather protecting agent on Such products, when applied to the instrument panels or the genuine leather surface.
Page 688: Cleaning The Outside Of Your Vehicle
Vehicle care and maintenance Cleaning the outside of your vehicle CAUTION N00945700061 To protect your vehicle’s finish, wash it often and thoroughly. When washing the underside of your vehicle or the wheels, wear a pair of gloves to protect your hands. If desired, you may wax your vehicle using a nonabrasive auto- If your vehicle has rain sensor wipers, place the mobile wax.
Page 689 Vehicle care and maintenance NOTE CAUTION When the door is frozen, opening it by force may tear off When using high-pressure water to wash a vehicle or crack the rubber gasket installed around the door. Pour equipped with the F.A.S.T.-key system, keep the warm water to melt the ice.
Page 690: Chrome Parts
Vehicle care and maintenance Cleaning plastic parts CAUTION N00946300178 Do not put wax on the areas having black matte Use a sponge or chamois to clean these parts. coating because it can cause uneven discoloration, If a vehicle wax sticks to a gray or black rough surface of the patches, blurs, etc.
Page 691: Wiper Blades
Vehicle care and maintenance Aluminum wheels (if so equipped) Wiper blades N00946500196 N00946700097 Use a soft cloth and glass cleaner to remove grease, dead 1. Remove dirt using a wet sponge. insects, etc., from the wiper blades. 2. Use a mild detergent on any dirt that cannot be removed Replace the wiper blades when they no longer clean the wind- easily with water.
Page 692: Engine Compartment
Vehicle care and maintenance Engine compartment N00947000042 Never spray or splash water on the electrical components in the engine compartment, as this may cause damage. Do not allow any nearby parts (such as plastic parts) come into contact with sulphuric acid (battery electrolyte), which may crack, stain, or discolour them.
Page 693 I n f o r ma t i o n P r o v i d e d b y :...
Page 694: Customer Assistance/ Reporting Safety Defects
Customer assistance/Reporting Safety Defects Consumer information (For vehicles sold in U.S.A.) ....8- Reporting Safety Defects ....8- Important facts to know in case of an accident .
Page 695: Uniform Tire Quality Grading
Customer assistance/Reporting Safety Defects Consumer information (For vehicles sold in WARNING U.S.A.) The traction grade assigned to this tire is based on N01047100100 straight-ahead braking traction tests, and does not This information is provided in compliance with the require- include acceleration, cornering, hydroplaning, or ments of the National Highway Traffic Safety Administration, peak traction characteristics.
Page 696: Reporting Safety Defects
Tower C Ottawa, Ontario K1A 0N5 NHTSA Headquarters 1200 New Jersey Avenue, SE To contact Mitsubishi Motor Sales of Canada, Inc. call 1- West Building 888-576-4878 or write to: Washington, DC 20590 Mitsubishi Motor Sales of Canada, Inc.
Page 697 Customer assistance/Reporting Safety Defects For vehicles sold in Puerto Rico For vehicles sold in American Samoa To contact Mitsubishi Motor Sales of Caribbean, Inc. To contact Pacific Marketing Inc. call 1-787-251-8715 or write to: call 684(699)9140 or write to: Mitsubishi Motor Sales of Caribbean, Inc.
Page 698: Specifications
Key information to discuss with your insurance a choice. So, if you want genuine Mitsubishi Motors parts, you may have to specifically request them. Make certain your company insurance company understands imitations are not to be used in Understand your repair estimate before approving repairs.
Page 699 I n f o r ma t i o n P r o v i d e d b y :...
Page 700: Table Of Contents
Specifications Vehicle labeling ......9- Vehicle dimensions ......9- Vehicle weights .
Page 701: Vehicle Labeling
Specifications Vehicle labeling Vehicles with turbocharger N01147400667 Keep a record of the chassis number and vehicle identification number. Such information will assist the police if your vehicle is stolen. Except for vehicles with turbocharger 1 - Vehicle emission control information label The vehicle emission control information label is affixed on the inside panel of the engine hood.
Page 702: Chassis Number
Specifications Chassis number The chassis number is stamped on the floor under the front pas- senger seat. It is visible by pulling back the carpet flap as shown in the illustration. 4 - Vehicle information code plate The vehicle information code plate is located on the front pas- senger door sill.
Page 703: Engine Serial Number
Specifications Engine serial number Tire and loading information placard The engine serial number is stamped on the cylinder block as N01148100528 The tire and loading information placard is located on the shown in the illustration. driver’s door sill. *- Front of the vehicle I n f o r ma t i o n P r o v i d e d b y :...
Page 704 Specifications Certification label Type 1 N01148200196 The certification label (A) is located on the driver’s door sill. Type 2 I n f o r ma t i o n P r o v i d e d b y :...
Page 705: Vehicle Dimensions
Specifications Vehicle dimensions N01147500482 Item Vehicles with 16 inch tire Vehicles with 18 inch tire Overall length 180.0 in (4,570 mm) Overall width 69.4 in (1,760 mm) Overall height 58.3 in (1,480 mm) 58.7 in (1,490 mm) Wheel base 103.7 in (2,635 mm) I n f o r ma t i o n P r o v i d e d b y :...
Page 706: Vehicle Weights
Specifications Vehicle weights N01147600874 2.0 liter 2.4 liter Front-wheel drive All-wheel drive vehi- Front-wheel drive All-wheel drive vehi- Item vehicles cles vehicles cles Gross vehicle weight rating (GVWR) 3,969 lb (1,800 kg) 4,388 lb (1,990 kg) 4,079 lb (1,850 kg) 4,190 lb (1,900 kg) Front 2,227 lb (1,010 kg)
Page 707: Engine Specifications
Specifications Engine specifications N01147700439 2.0 liter Item 2.4 liter Except for vehicles with tur- Vehicles with turbocharger bocharger Engine model 4B11 4B12 Engine displacement 121.9 CID (1,998 cm³) 144.0 CID (2,360 cm³) No. of cylinders and cylinder arrange- 4 in-line ment Bore 3.39 in (86.0 mm)
Page 708: Tires And Wheels
Offset 1.81 in (46 mm) PCD: Pitch Circle Diameter (installation holes) NOTE Contact an authorized Mitsubishi Motors dealer for details on the combination used on your vehicle. These tires satisfy vehicle loading conditions described in this owner’s manual. I n f o r ma t i o n P r o v i d e d b y :...
Page 709: Refill Capacities
4.5 qt (4.3 L) 2.4 liter Oil filter .32 qt (0.3 L) Power steering As required Genuine Mitsubishi Power Steering Fluid DiaQueen NEW MULTI GEAR OIL API classifica- Manual transaxle 2.6 qt (2.5 L) tion GL-3 SAE 75W-80 Continuously variable transmission (CVT) 7.5 qt (7.1 L)
Page 710 Specifications Item Capacity Lubricants .95 qt (0.9 L) AWC control fluid {Includes DIAMOND ATF SP III hydraulic piping} Except for vehicles with ACD .53 qt (0.5 L) Hypoid gear oil API classification GL-5 SAE 80 Rear differential oil Vehicles with ACD .58 qt (0.55 L) DiaQueen LSD gear oil Brake/Clutch (if so equipped)
Page 711 I n f o r ma t i o n P r o v i d e d b y :...
Page 712: Table Of Contents
Alphabetical index Handling of compact discs 5-145 Steering wheel audio remote control switch 5-134 Automatic air conditioning 5-31 5-41 Accessory (installation) 1-8 Auxiliary audio connector (RCA) 5-132 ACD (Active center differential system) 3-132 Auxiliary video connector (RCA) 5-132 ACD control mode display 3-134 AWC control fluid 7-20 ACD control mode switch 3-133 ACD warning display 3-134...
Page 713: Table Of Contents
Alphabetical index Parking brake lever stroke 7-39 Continuously variable transmission (CVT) 3-98 Pedal 3-143 Fluid 7-18 9-10 Pedal free play 7-38 Selector lever operation 3-98 Power brakes 3-144 Sports mode 3-106 Service brake 3-143 Coolant (engine) 7-12 9-10 Break-in recommendations 3-2 Cruise control 3-157 Bulb capacity 7-55 Indicator 3-159...
Page 714: Table Of Contents
Alphabetical index Lock 3-51 Floor console box 3-300 Power door locks 3-55 Floor mat 4-3 Drive mode indicator 3-137 Fluid 9-10 Drive mode-selector 3-136 AWC control fluid 7-20 Driving during cold weather 4-6 Brake fluid 7-21 9-10 Driving, alcohol and drugs 4-2 Clutch fluid 7-21 9-10 Continuously variable transmission (CVT) fluid 7-18...
Page 715: Table Of Contents
Alphabetical index Fuel hoses 7-42 Hood lock release mechanism and safety catch 7-44 Modification/alterations to the electrical or fuel systems 1-9 Horn switch 3-255 Tank capacity 1-5 9-10 Fuel selection 1-2 Fuses 7-46 If the vehicle breaks down 6-2 Fusible links 7-45 Ignition switch 3-24 3-85 Important facts to know in case of an accident 8-5...
Page 716: Table Of Contents
Alphabetical index Link System 3-256 Loading information 4-9 Lubricants 9-10 Parking 4-8 Luggage floor boxes 3-301 Parking brake 3-77 Parking brake lever stroke 7-39 Polishing 7-93 Malfunction indicator 3-229 Power brakes 3-144 Manual air conditioning 5-22 Power door locks 3-55 Manual transaxle 3-94 Power steering Oil 7-18...
Page 717: Table Of Contents
Alphabetical index Rear window defogger switch 3-254 Seat belt use during pregnancy 2-21 Rear-view camera 3-172 Service brake 3-143 Rearview mirror Service precautions 7-2 Inside 3-80 Snow tires 7-37 Outside 3-83 Spark plugs 7-41 Refrigerant (air conditioning) 9-10 Steering Replacement of light bulbs 7-55 Power steering fluid 7-22 9-10 Replacing tires and wheels 7-34...
Page 718: Table Of Contents
Alphabetical index Size (tire and wheel) 9-9 Warning display 3-116 Snow tires 7-37 Tire and loading information placard 4-10 Tire chains 7-37 USB input terminal 3-283 Tread wear indicators 7-35 How to connect an iPod 3-285 Tissue holder 3-301 USB input terminal device Tools 6-7 How to connect a USB memory 3-283 Storage 6-7...
Page 719 Alphabetical index Wiper Rain sensor 3-248 Windshield 3-246 Wiper blades 7-40 I n f o r ma t i o n P r o v i d e d b y :...
Page 720 I n f o r ma t i o n P r o v i d e d b y :...
Page 721 How to calculate your gasoline mileage You can calculate your miles-per-gallon or kilometers-per-litre 3. Refill the fuel tank. Record the odometer mileage again, by using the following process: as well as the gallons/litres of fuel used. 4. Subtract the first mileage number from the second number 1.
Page 722: Maintenance Record
NOTE Name of Owner Date of Purchase Address of Owner Model of Vehicle Name and Address of Dealer Vehicle Identification Number Maintenance record Kilometers Service Performed Date Inspection and Maintenance Item Miles I n f o r ma t i o n P r o v i d e d b y :...

Mitsubishi LANCER 2012 Manual

Quick Links

Related Manuals for Mitsubishi LANCER 2012

Summary of Contents for Mitsubishi LANCER 2012