ADTRAN BLUESOCKET 2135 Quick Start Manual

Hide thumbs

page of 8

/ 8
Bookmarks

Quick Links

Download this manual

LUESOCKET

P/N 1700962F1

ARDWARE

The following items are included in your shipment:

•

Bluesocket 2135 Access Point (BSAP)

•

One plane bracket with hardware

Four expansion bolts with washers and nuts

Four hex cap screws with washers and lock washers

•

One pole mounting base with hardware

One hose strap

Four round head screws with washers and lock washers

•

Watertight PoE fitting

•

Grounding cable

NTENNAS

The BSAP 2135 provides six N-type antenna connectors (no integrated antennas are included). These

connectors support two internal 802.11 radios: one 2.4 GHz 802.11b/g/n radio and one 5 GHz

802.11a/n/ac radio. There are three antenna connectors for each band labeled 2.4GHz and 5GHz. A set

of six high-efficiency omnidirectional antennas can be ordered from ADTRAN for the BSAP 2135

(P/N 1700930F1, three 5 GHz, 7 dBi gain and three 2.4 GHz, 5 dBi gain).

Make a note of the 12-character MAC address and 14-digit serial number

listed on the back of the BSAP 2135 before mounting the AP to a wall or other

surface. This information will be required during configuration.

Quick Start Guide, 61700962F1-13B, May 2015

2135 A

CCESS

Antenna Connectors

Grounding Point

OINT

Watertight

PoE Fitting

Need help?

Do you have a question about the BLUESOCKET 2135 and is the answer not in the manual?

Questions and answers

Summary of Contents for ADTRAN BLUESOCKET 2135

Page 1 802.11a/n/ac radio. There are three antenna connectors for each band labeled 2.4GHz and 5GHz. A set of six high-efficiency omnidirectional antennas can be ordered from ADTRAN for the BSAP 2135 (P/N 1700930F1, three 5 GHz, 7 dBi gain and three 2.4 GHz, 5 dBi gain).
Page 2: Mounting The Bsap
BSAP OUNTING THE TO AN XTERIOR EILING OR BSAPs can be mounted in exterior applications or interior applications in harsh environments with an operating temperature range of -40°F to 131°F (-40°C to 55°C). BSAPs should be positioned for maximum throughput and range between other APs and wireless client devices. Follow these instructions to mount the BSAP 2135 to a ceiling or wall: On a flat mounting surface, mark the locations of the four mounting holes using the plane bracket as a template (Figure 1).
Page 3 BSAP OUNTING THE TO A The BSAP 2135 also ships with a pole mount base and hose strap to mount the AP to a vertical or horizontal pole. BSAPs should be positioned for maximum throughput and range between other APs and wireless client devices.
Page 4 To mount the BSAP 2135 to a horizontal pole: Place the lock washers, then the flat washers on the four hex cap screws, and drive the screws through the plane bracket into the back of the case as shown in Figure 4. Drive the four round head screws to attach the pole mount base to the plane bracket in a horizontal position (Figure 8).
Page 5 Disassemble the watertight fitting by unscrewing the cinch nut and pushing the rubber gasket out of the strain-relief fitting. Thread the cinch nut onto the customer-provided RJ-45 CAT 5e or CAT 6 cable. Spread the gasket open and wrap it around the cable near the RJ-45 connector. Insert the RJ-45 connector through the strain-relief fitting, and press the gasket back into its original position.
Page 6 GR-1089-Core Criteria B Protection Surge Protection ADTRAN recommends forming a 3 to 5-inch drip loop on outdoor cables where water could run along the cable and enter the BSAP 2135, PoE injector, or building. If the cables are oriented so that water cannot possibly enter, drip loops are not necessary.
Page 7 AP Discovery configuration guide available online at https://supportforums.adtran.com. 1. After powering the AP and connecting it to the network, allow the AP to discover the vWLAN appliance to receive its configuration information. This AP discovery process uses an algorithm that attempts discovery methods in this order: static configuration, DHCP vendor option (43), Domain Naming System (DNS) discovery, and cached vWLAN information.
Page 8 GNU General Public License (GPL). For a list of third-party software and their licenses, go to http://www.adtran.com/software/EULA. You can obtain the complete corresponding source code of such software components from ADTRAN for a period of three years after our last shipment of this product by sending a money order or check for $5 to: ADTRAN, Inc, P.O.

This manual is also suitable for:

1700962f1