Related Manuals for Aaeon PC-3200
Summary of Contents for Aaeon PC-3200
- Page 1 F a n l e s s P a n e l P C s P C - 3 2 0 0 PC-3200 VIA Eden Processor-based Fanless Panel PC with 12.1” TFT-LCD PC-3200 Series User Manual V1.2...
-
Page 2: Copyright Notice
AAEON, assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users. PC-3200 Series User Manual V1.2... -
Page 3: Acknowledgments
UMC is a trademark of United Microelectronics Corporation. SMI is a trademark of Silicon Motion, Inc. Creative is a trademark of Creative Technology LTD. All other product names or trademarks are properties of their respective owners. PC-3200 Series User Manual V1.2... -
Page 4: Fcc Class B
• Consult the dealer or an experienced radio/TV technician for help Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your authority to operate the equipment. PC-3200 Series User Manual V1.2... -
Page 5: Packing List
Input voltage rated 18 V ~ 25 Vdc, 3.5 A max Use a 3 V @ 195 mA lithium battery Packing: please carry the unit with both hands, handle with care PC-3200 Series User Manual V1.2... - Page 6 P C - 3 2 0 0 Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator CompactFlash: Turn off power before inserting or removing CompactFlash storage card. PC-3200 Series User Manual V1.2...
-
Page 7: Safety & Warranty
12. Never pour any liquid into an opening. This may cause fire or electrical shock. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. PC-3200 Series User Manual V1.2... - Page 8 The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. AAEON disclaims all responsibility for the accuracy of any statements contained herein. PC-3200 Series User Manual V1.2...
-
Page 9: Table Of Contents
Installing the 2.5" Hard Disk Drive (HDD) ......28 Installing the battery pack............ 33 Panel Mounting Installation..........34 Jumper Settings and Connectors..........35 Jumpers and Connectors ............36 Jumpers and switch .............. 37 Locating jumpers and switch ..........38 PC-3200 Series User Manual V1.2... - Page 10 Power Management Setup ........... 55 PnP/PCI Configurations............56 PC Health Status ..............57 Frequency/Voltage Control ..........58 Load Optimized Defaults............. 59 Set Password ................ 60 Save & Exit Setup..............62 Exit Without Saving............. 62 Drivers Installation............... 63 PC-3200 Series User Manual V1.2...
-
Page 11: General Information
F a n l e s s P a n e l P C s P C - 3 2 0 0 Chapter General Information PC-3200 Series User Manual V1.2... -
Page 12: Introductions
It is a PC-based system with 12.1" color TFT LCD display, on-board PCI Ethernet controller, multi-COM port interfaces and an audio controller. With a built-in internal IDE connectors, the PC-3200 is as compact and user friendly as a multi-function computer. In addition, its "fit anywhere" design makes it very flexible and able to be used in many different kinds of installations. -
Page 13: General Specifications
IDE devices. Each channel supports PIO modes 0 ~ 4, DMA mode 0 ~ 2, and Ultra DMA 33/66/100 simultaneously. The secondary connector is designated for the CD-ROM drive or CompactFlash card. BIOS supports IDE CDROM bootup PC-3200 Series User Manual V1.2... - Page 14 Chipset: VIA Twister chip w/ integrated Savage4 2D/3D/Video Accelerator Frame buffer: Supports 8/16/32 MB frame buffer w/ system memory Interface: 4X AGP VGA/LCD interface, Support for 9, 12, 15, 18, 24, 36 bit TFT and optional 16- or 24-bit DSTN panel PC-3200 Series User Manual V1.2...
- Page 15 100/10Base-T auto-sensing capability Wake-on-LAN: Supports Wake-on-LAN function with ATX power control Touchscreen (Optional) Analog Resistive Type Continuous Resolution Light Transmission RS232 interface (users COM4) Controller <5 V@ 100mA Power Consumption Supports Windows NT/98 Software Driver /2000/ME/XP PC-3200 Series User Manual V1.2...
- Page 16 -20℃ to 60℃ (-4 ~ 149℉) Relative humidity: 10 ~ 95% @ 40° C (non-condensing) Shock: 10 G peak acceleration (11 msec duration) Certification: EMC: CE Class A/ FCC Class B/; Safety: UL1950 Vibration: 1G/5~500Hz/Random vibration PC-3200 Series User Manual V1.2...
-
Page 17: Lcd Specifications
* The VR control is defined by hot key in DOS or BIOS mode as below: Ctrl-Alt-F3, Ctrl-Alt-F4. Note: All AAEON's LCD products are manufactured with High precision technology. However, in all LCD panels there maybe a small number of defective pixels that do not change color. -
Page 18: Dimensions
F a n l e s s P a n e l P C s P C - 3 2 0 0 Dimensions PC-3200 Series User Manual V1.2... -
Page 19: System Setup
F a n l e s s P a n e l P C s P C - 3 2 0 0 Chapter System Setup PC-3200 Series User Manual V1.2... -
Page 20: A Quick Tour Of The Panel Pc
When you place the panel PC upright on the desktop, its front panel appears as shown in Figure 2-1. Figure 2.1: Front view of PC-3200 panel PC When you turn the panel PC around and look at its rear cover, you will find the I/O section as shown in Fig. - Page 21 P C - 3 2 0 0 Figure 2.2: Rear view of the panel PC CompactFlash socket Compact CD-ROM drive CFC eject button CD-ROM activity light CD-ROM eject button Speaker Figure 2.3: Side view of the panel PC PC-3200 Series User Manual V1.2...
-
Page 22: Installation Procedures
Y-shaped adapter or serial ports. Switching on the power When you look at the rear side of the panel PC, you will see the power switch as shown in Figure 2-2. PC-3200 Series User Manual V1.2... -
Page 23: Running The Bios Setup Program
The settings you specify with the setup program are recorded in a special area of memory called CMOS RAM. This memory is backed up by a battery so that it will not be erased when you turn off or reset the system. PC-3200 Series User Manual V1.2... -
Page 24: Installing System Software
Method 2: Use the COM or parallel port You can use Lap Link 6 or similar transmission software. Connect another PC to the PC-3200 with an appropriate cable and transmit the software to the PC-3200. PC-3200 Series User Manual V1.2... - Page 25 SVGA, audio, and touch screen functions. All drivers are stored in a CD-ROM disc entitled "Drivers and Utilities" which can be found in your accessory box. The standard procedures for installing the drivers are described in Chapters 5, 6, 7, 8 respectively. PC-3200 Series User Manual V1.2...
- Page 26 The various drivers and utilities in the CD-ROM disc have their own text files which help users install the drivers and understand their functions These files are a very useful supplement to the information in this manual. PC-3200 Series User Manual V1.2...
-
Page 27: Hardware Installation And Upgrading
F a n l e s s P a n e l P C s P C - 3 2 0 0 Chapter Hardware Installation and Upgrading PC-3200 Series User Manual V1.2... -
Page 28: Introduction
PC's internal controller which uses a PCI local-bus interface. The advanced IDE controller supports faster data transfer and allows the IDE hard drive to exceed 528 MB. The following are instructions for installation: PC-3200 Series User Manual V1.2... - Page 29 There is a metal plate, which holds the HDD to the upper left-hand side of the metal shielding case. (See Figure 3.1) 2.5” HDD Metal plate Plastic rear cover Figure 3.1: Installing primary 2.5” HDD PC-3200 Series User Manual V1.2...
- Page 30 IDE hard drive, with Pin 1 on the cable corresponding to Pin 1 on the hard drive. Note: To avoid the IDE cable being discounted by the CD-ROM cable, please arrange the CD-ROM cable first before connect the IDE cable. PC-3200 Series User Manual V1.2...
- Page 31 F a n l e s s P a n e l P C s P C - 3 2 0 0 Put the plastic rear cover on and tighten the screws. DC outlet Power button The inner edge PC-3200 Series User Manual V1.2...
- Page 32 2) Cross the power button over the rear cover hole. 3) Cross the DC plug-in housing (female) over the rear cover hole. 4) Make sure the entire alignment indicator lodge in the inner edge. PC-3200 Series User Manual V1.2...
-
Page 33: Installing The Battery Pack
1. Pull up the battery door cover on the right bottom of PC-3200 2. Put the battery pack in, and then connect the battery cable to battery connector in the PC-3200. Make sure the red wire corresponds to Pin 1 on the connector. -
Page 34: Panel Mounting Installation
Plug the mounting brackets into the hole around the display (see the following illustration on the left). Push the mounting brackets forward to make it fixed. Fix the brackets with screws until the display panel is firmly mounted in the wall. PC-3200 Series User Manual V1.2... -
Page 35: Jumper Settings And Connectors
F a n l e s s P a n e l P C s P C - 3 2 0 0 Chapter Jumper Settings and Connectors PC-3200 Series User Manual V1.2... -
Page 36: Jumpers And Connectors
If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. Generally, you simply need a standard cable to make most connections PC-3200 Series User Manual V1.2... -
Page 37: Jumpers And Switch
P C - 3 2 0 0 Jumpers and switch The motherboard of the PC-3200 has a number of jumpers that allow you to configure your system to suit your applications. The table below lists the function of each of the board’s jumpers. -
Page 38: Locating Jumpers And Switch
F a n l e s s P a n e l P C s P C - 3 2 0 0 Locating jumpers and switch Figure 4.1: Jumpers on the PC-3200 motherboard PC-3200 Series User Manual V1.2... -
Page 39: Connectors
F a n l e s s P a n e l P C s P C - 3 2 0 0 Connectors Onboard connectors link the PC-3200 to external devices such as external hard disk drives or floppy drives. The table below lists the function of each of the board’s connectors. - Page 40 F a n l e s s P a n e l P C s P C - 3 2 0 0 Figure 4.2: Connectors on the PC-3200 motherboard PC-3200 Series User Manual V1.2...
-
Page 41: Cmos Clear For External Rtc (J5)
Short pin 2 and pin 3. Return jumper to pins 1 and 2. Turn on the system. The BIOS is now reset to its default setting. Table 4.3: CMOS clear (J5) *Normal operation Clear CMOS * default setting PC-3200 Series User Manual V1.2... -
Page 42: Com-Port Interface (J2, J3, J4)
RS-232/422/485) in one COM port connector. COM2 RS-232/422/485 setting (J2) COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode. This is done via J2. Table 4.4: COM2 RS-232/422/485 setting (J2) *RS-232 RS-422 RS-485 PC-3200 Series User Manual V1.2... - Page 43 COM3 and COM4 are another set. Their selectable function is the same as the COM1/COM2 set Table 4.5: Serial port default settings Port Address Range Interrupt COM1 3F8 ~ 3FF IRQ4 COM2 2F8 ~ 2FF IRQ3 COM3 3E8 ~ 3EF IRQ10 COM4 2E8 ~ 2EF IRQ5 PC-3200 Series User Manual V1.2...
- Page 44 *default setting Note: Pins 1, 3 and 5 are for COM1 Pins 2, 4 and 6 are for COM2 Pins 7, 9 and 11 are for COM3 Pins 8, 10 and 12 are for COM4 PC-3200 Series User Manual V1.2...
-
Page 45: Vga Interface
When the watchdog timer activates (i.e. CPU processing has come to a halt), it can reset the system or generate an interrupt on IRQ11. This can be set via jumper J4 as shown below: Table 4.7: Watchdog activity selection (J4) *System reset IRQ11 *default setting PC-3200 Series User Manual V1.2... -
Page 46: Wake On Lan Select (J1)
P C - 3 2 0 0 Wake on LAN select (J1) The PC-3200 provides Wake-on LAN function when ATX power is used. To enable Wake-on LAN function, the J1 should be set as shown below: Table 4.8: Wake-On-LAN select (J1) -
Page 47: Bios Installation
F a n l e s s P a n e l P C s P C - 3 2 0 0 Chapter BIOS Installation PC-3200 Series User Manual V1.2... -
Page 48: System Test And Initialization
F a n l e s s P a n e l P C s P C - 3 2 0 0 The PC-3200 comes with an Award BIOS chip that contains the ROM setup for your system. This chip serves as an interface between the processor and the rest of the main board’s components. - Page 49 The CMOS memory has lost power and the configuration information has been erased. The PC-3200 CMOS memory has an integral lithium battery backup. The battery backup should last ten years in normal service, but when it finally runs down, you will need to replace the complete unit.
-
Page 50: Award Bios Setup
This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering setup Power on the computer and press <Del> immediately. This will allow you to enter Setup. PC-3200 Series User Manual V1.2... -
Page 51: Standard Cmos Features Setup
Once a field is high lighted, on-line help information is displayed in the left bottom of the Menu screen. PC-3200 Series User Manual V1.2... -
Page 52: Advanced Bios Features Setup
Screen menu, the screen below is displayed. Users are not encouraged to run the BIOS and Chipset Features setup programs. Your system should have been fine-tuned before shipping. Improper setup may cause the system to fail, so consult your dealer before making any changes. PC-3200 Series User Manual V1.2... -
Page 53: Advanced Chipset Features Setup
By choosing the Advanced Chipset Features option from the Initial Setup Screen menu, the screen below is displayed. Note: It is strongly recommended that setup items in this section NOT be changed, because advanced knowledge is required to effect such changes. PC-3200 Series User Manual V1.2... -
Page 54: Integrated Peripherals
F a n l e s s P a n e l P C s P C - 3 2 0 0 Integrated Peripherals Choosing the Integrated Peripherals option from the Initial Setup Screen menu should produce the screen below. Here we see the default values for the PC-3200. PC-3200 Series User Manual V1.2... -
Page 55: Power Management Setup
F a n l e s s P a n e l P C s P C - 3 2 0 0 Power Management Setup By choosing the Power Management Setup option from the Initial Setup Screen menu, the screen below is displayed. PC-3200 Series User Manual V1.2... -
Page 56: Pnp/Pci Configurations
F a n l e s s P a n e l P C s P C - 3 2 0 0 PnP/PCI Configurations By choosing the PnP/PCI Configurations option from the Initial Setup Screen menu, the screen below is displayed. PC-3200 Series User Manual V1.2... -
Page 57: Pc Health Status
F a n l e s s P a n e l P C s P C - 3 2 0 0 PC Health Status The PC Health Status option displays information such as CPU and motherboard temperatures, fan speeds, and core voltage. PC-3200 Series User Manual V1.2... -
Page 58: Frequency/Voltage Control
Frequency/Voltage Control By choosing the Frequency/Voltage Control option from the Initial Setup Screen menu, the screen below is displayed. Warning Incorrect settings in Frequency/Voltage Control may damage the system CPU, video adapter, or other hardware. PC-3200 Series User Manual V1.2... -
Page 59: Load Optimized Defaults
Load Optimized Defaults loads the default system values directly from ROM. If the stored record created by the Setup program should ever become corrupted (and therefore unusable), these defaults will load automatically when you turn the PC-3200 system on. PC-3200 Series User Manual V1.2... -
Page 60: Set Password
At the “Confirm Password” prompt, retype the new password, and press <Enter>. Select Save to CMOS and EXIT, type <Y>, then <Enter>. To Disable Password Choose the Set Password option from the CMOS Setup Utility main menu PC-3200 Series User Manual V1.2... - Page 61 Select Set Password again, and at the “Enter Password” prompt, don’t enter anything; just press <Enter>. At the “Confirm Password” prompt, again don’t type in anything; just press <Enter>. Select Save to CMOS and EXIT, type <Y>, then <Enter>. PC-3200 Series User Manual V1.2...
-
Page 62: Save & Exit Setup
This record is required for the system to operate. Exit Without Saving Selecting this option and pressing <Enter> lets you exit the Setup program without recording any new values or changing old ones. PC-3200 Series User Manual V1.2... -
Page 63: Drivers Installation
F a n l e s s P a n e l P C s P C - 3 2 0 0 Chapter Drivers Installation PC-3200 Series User Manual V1.2... - Page 64 F a n l e s s P a n e l P C s P C - 3 2 0 0 The PC-3200 comes with a CD, which contains most of drives and utilities of your needs. There are several ways of installation depending on the driver package under different Operating System application.
- Page 65 P C - 3 2 0 0 Installation 2: Applicable for Windows 9x/2000/ME/XP Insert the PC-3200 CD Diskette into the CD ROM Drive. Click on Start button, select the Settings, and then click on the Control Panel icon. Double click on the Add/Remove Hardware icon and Add New Hardware Wizard will appear.
- Page 66 Windows NT CD Diskette. Follow its instructions to complete the setup procedures.) 11. When the message The drivers were successfully installed is displayed, remove the display driver diskette, then click on the OK button. 12. Reboot the system PC-3200 Series User Manual V1.2...