I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Copyright Notice This document is copyrighted, 2003. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
O n y x - 1 5 8 / S Acknowledgments Intel and Pentium are registered trademarks of Intel® Corporation. IBM, PC/AT, PS/2 are trademarks of International Business Machines Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
I n d u s t r i a l P a n e l P C s Packing List Before installing your Panel PC, please check if the package contains the following items. Onyx-158/S series Panel PC CD-ROM Contains User’s Manual, Drivers and Utilities Accessories Screws bag Jumper packbag...
I n d u s t r i a l P a n e l P C s Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning.
I n d u s t r i a l P a n e l P C s 14. If any of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b.
I n d u s t r i a l P a n e l P C s Contents Copyright Notice ... 2 Acknowledgments ... 3 Packing List... 4 Safety & Warranty... 5 Charpter 1 General Information ... 9 Introductions... 10 Features: ...
Page 8
I n d u s t r i a l P a n e l P C s Advanced Chipset Features ... 40 Power management setup... 42 PC Health Status... 44 Frequency/Voltage Control ... 45 Load Fail-Safe Defaults... 46 Load Optimized Defaults... 46 Set Supervisor Password...
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Introductions The Onyx-158/S is a compact, All-in-one network compatible PC with full safety approval and features to control a dedicated system with a wide variety of applications.
I n d u s t r i a l P a n e l P C s Features: 15” high brightness color TFT LCD display Aluminum alloy front panel All-in-one FC Socket 370 SBC (CPU supports up to Pentium® III 1GHz, FSB 66/100/133MHz) Removable anti-vibration 2.5”...
I n d u s t r i a l P a n e l P C s Specifications: Construction: Heavy-duty steel chassis and aluminum alloy front panel Display: 15” XGA (1024 x 768) color TFT LCD CPU: Support Socket 370 based Intel® Pentium® III and Celeron® CPU, up to 1GHz Chipset: VIA VT8604 shared memory up to 32MB SDRAM Memory: Support up to 512MB...
I n d u s t r i a l P a n e l P C s LCD Specifications Display type Max. Resolution Max. Colors Dot size (mm) Luminance (cd/m Viewing angle Operating temperature Brightness Control Back Light MTBF (Hrs) Note: All AAEON's LCD products are manufactured with High precision technology.
I n d u s t r i a l P a n e l P C s Environmental Specification Operating temperature: 0°to 45℃ (32~122℉) Storage temperature: -20°to 60℃ (-4~140℉) Storage humidity: 5 to 90%, non-condensing Vibration: 10 to 150 Hz, 0.075mm peak to peak (operation) 10 cycles (sweep): 1 oct/min (endurance) Shock: 15G peak acceleration (11 msec.
I n d u s t r i a l P a n e l P C s The panel PC is a PC-based industrial computer that is housed in aluminum alloy front panel and heavy-duty steel chassis. You can install 2.5”HDD easily by removing the side cover of HDD drive bay.
Page 18
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S 3. Unscrew the 7 attachment screws from the HDD drive bay. 1. Place 2.5” HDD into the drive bay and connect the IDE ribbon cable. 2.
Page 19
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S 6. Mount the drive bay into the machine by two screws. Onyx-158/S Series User Manual V1.2...
I n d u s t r i a l P a n e l P C s Removing the rear maintenance cover Remove the HDD module first then unscrew the two attachment screws from the top cover of the desktop stand. Caution: Handle the desktop stand with care, since it is made of aluminum and is weight 3kilogram.
Page 21
I n d u s t r i a l P a n e l P C s 3. Remove the stand holder by unscrewing the four attachment screws. 4. Unscrew the ten attachment screws used to hold the rear maintenance cover.
Page 22
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Mounting Installing Onyx-158/S is suitable for VESA75/100mm interface pads for arm mounting or desktop stand.
I n d u s t r i a l P a n e l P C s Safety precautions Warning! Always completely disconnect the power cord from your chassis whenever you are working on it. Do not make connections while the power is on because sensitive electronic components can be damaged by the sudden rush of power.
I n d u s t r i a l P a n e l P C s CPU Card - PCM-6898 Jumper Setting Board Layout CN15 CN16 JP11 J9(IR) CN18 CN19 CN8(LAN) Onyx-158/S Series User Manual V1.2 O n y x - 1 5 8 / S FAN1 CN20 DIMM1...
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Board Dimensions Onyx-158/S Series User Manual V1.2...
Page 27
I n d u s t r i a l P a n e l P C s List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The following tables show the function of each of the board's jumpers. Jumpers Label J3/4...
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Setting Jumpers You configure your card to match the needs of your application by setting jumpers.
I n d u s t r i a l P a n e l P C s DOC Address Setting (J2) 1-2, 3-4 *Default Audio Port CD_IN (J3 & J4) J3-2.54mm J4-2.00mm For PCM-3730 (J5) Onyx-158/S Series User Manual V1.2 O n y x - 1 5 8 / S Function Disabled...
Page 30
I n d u s t r i a l P a n e l P C s IrDA Connector (J9) VIO Select (JP3) You can use JP3 to set the voltage input/output at 5 volts or 3.3 volts. *Default Wake On LAN (JP6) *Default Onyx-158/S Series User Manual V1.2...
I n d u s t r i a l P a n e l P C s RS-232/422/485 COM2 (JP4,JP5) Setting 1-2, 4-5, 7-8, 10-11 2-3, 5-6, 8-9, 11-12 2-3, 5-6, 8-9, 11-12 *Default Auto detect CPU Frequency (JP7/JP8) System Frequency (JP9 &...
I n d u s t r i a l P a n e l P C s Clear CMOS (JP11) You can use JP11 to clear the CMOS data if necessary. To reset the CMOS data, place a jumper on JP11 (Clear CMOS) for just a few seconds, and then remove the jumper to the (Protect) position.
I n d u s t r i a l P a n e l P C s System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen.
I n d u s t r i a l P a n e l P C s Award BIOS setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Use this menu to change the values in the chipset registers and optimize your system’s performance.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Standard CMOS Features When you choose the Standard CMOS Features option from the INITIAL SETUP SCREEN menu, the screen shown below is displayed.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Advanced BIOS Features By choosing the Advanced BIOS Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Advanced Chipset Features By choosing the Advanced Chipset Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed.
Page 41
I n d u s t r i a l P a n e l P C s Integrated Peripherals By choosing the Integrated Peripherals from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Power management setup By choosing the Power Management Setup from the INITIAL SETUP SCREEN menu, the screen below is displayed.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S PnP/PCI Configurations By choosing the PnP/PCI configurations from the Initial Setup Screen menu, the screen below is displayed.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S PC Health Status By choosing the PC Health Status from the Initial Setup Screen menu, the screen below is displayed.
I n d u s t r i a l P a n e l P C s Frequency/Voltage Control By choosing the Frequency/Voltage Control from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-6898.
I n d u s t r i a l P a n e l P C s Load Fail-Safe Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Load Fail-Safe Default (Y/N)? Pressing "Y"...
I n d u s t r i a l P a n e l P C s Setup Enter a password whenever you enter Setup. NOTE: To clear the password, simply press Enter when asked to enter a password. Then the password function is disabled.
I n d u s t r i a l P a n e l P C s O n y x - 1 5 8 / S Chapter Drivers Installation Onyx-158/S Series User Manual V1.2...
Page 49
I n d u s t r i a l P a n e l P C s The Onyx-158/S comes with a CD, which contains most of drives and utilities of your needs. There are several ways of installation depending on the driver package under different Operating System application.
Page 50
I n d u s t r i a l P a n e l P C s the following path: “cd-rom”: \Driver\ CPU Board\ PCM-6898\ Step 3 – Install Ethernet Driver” “cd-rom”: \Driver\ CPU Board\ PCM-6898\ Step 4 – Install Audio Driver”...