Page 1
OMNI-BT Series Industrial Modular Touch Panel PC With Intel® Bay Trail Platform User’s Manual 2 Last Updated: March 30, 2018...
Page 2
AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users.
Page 3
Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft Windows is a registered trademark of Microsoft Corp. Intel, Pentium, Celeron, and Xeon are registered trademarks of Intel Corporation Core, Atom are trademarks of Intel Corporation ...
Page 4
Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity OMNI-BT Series Panel PC (panel size from 10.4 – 21.5”) Product CD with drivers Phoenix Power connector If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Page 5
(if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the AAEON.com for the latest version of this document. Preface...
Page 6
All cautions and warnings on the device should be noted. All cables and adapters supplied by AAEON are certified and in accordance with the material safety laws and regulations of the country of sale. Do not use any cables or adapters not supplied by AAEON to prevent system malfunction or fires.
Page 7
As most electronic components are sensitive to static electrical charge, be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and contain all electronic components in any static-shielded containers. If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii.
Page 8
FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Caution: There is a danger of explosion if the battery is incorrectly replaced.
Page 10
China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Panel PC/ Workstation Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB & Other ○...
Page 12
List of Jumpers 2.2.1 Clear CMOS (JP1) ..................37 2.2.2 AT/ATX Mode Selection (JP3) ..............37 2.2.3 LVDS Port Backlight Lightness Control Mode Selection (JP4) ..37 2.2.4 LVDS Inverter Voltage Selection (JP5) ..........37 2.2.5 Touch Selection (JP8) ................38 2.2.6 COM2 +12V/+5V/Ring Selection (JP9) ..........
Page 13
Installing the Hard Disk Drive Installing DRAM Mount the OMNI onto the wall Assemble the OMNI panel and the CPU Box P-CAP Touch Screen Operating Chapter 3 - AMI BIOS Setup ....................66 System Test and Initialization AMI BIOS Setup Setup Submenu: Main Setup Submenu: Advanced 3.4.1...
Specifications System Intel® Celeron® J1900, 2 GHz Processor Intel® Atom™ N2807, 1.58 GHz 204-pin DDR3L 1333 MHz SODIMM x 1, up to System Memory 8 GB, (J1900) 204-pin DDR3L 1333 MHz SODIMM x 1, up to 4 GB, (N2807) Intel 10/100/100Base-TX, RJ-45 x 2 Ethernet ...
Page 17
Support OMNI-2155/2215/3155/3175/3195 Series Panel PC Windows® 10 OS Support Windows ® Windows® 7 Windows Embedded Standard 7 Linux kernel 2.6.x or above Environmental -10°C~60°C with industrial grade device (with Operating Temperature 0.5 m/s air flow, according to IEC68-2-14, CPU: N2807) -10°C~55°C with industrial grade device (with 0.5 m/s air flow, according to IEC68-2-14, CPU: J1900)
Page 18
Power Supply 9 ~ 30 V DC Input Chapter 1 – Product Specifications...
1.1.1 OMNI-3105-BT Mechanical IP65/ NEMA 4 for aluminum front bezel Construction Panel Mount / VESA 100 Mounting 280 x 239 x 59 mm (11 x 9.4 x 2.3") Dimension (W x H x D) Carton Dimension ...
1.1.2 OMNI-3125-BT Mechanical IP65/ NEMA 4 for aluminum front bezel Construction Panel Mount / VESA100 Mounting 329 x 288 x56 mm (13 x 11.3 x 2.2") Dimension (W x H x D) Carton Dimension 530 x 445 x 200 mm (20.9 x 17.5 x 7.9") (W x H x D) Gross Weight ...
1.1.3 OMNI-3155-BT Mechanical IP65/ NEMA 4 for aluminum front bezel Construction Panel Mount / VESA 100 Mounting 369 x 314 x 58 mm (14.5 x 12.4 x 2.3") Dimension (W x H x D) Carton Dimension 522 x 478 x 262 mm (20.6 x 18.8 x 10.3") (W x H x D) Gross Weight...
1.1.4 OMNI-2155 Mechanical IP65/ NEMA 4 for aluminum front bezel Construction Panel Mount / VESA 100 Mounting 420 x 265 x 60 mm (16.5 x 10.4 x 2.4") Dimension (W x H x D) Carton Dimension 530 x 445 x 200 mm (20.9 x 17.5 x 7.9") (W x H x D) Gross Weight...
1.1.5 OMNI-3175-BT Mechanical IP65/ NEMA 4 for aluminum front bezel Construction Panel mount / VESA100 Mounting 400 x 370 x 59 mm (15.7 x 14.6 x 2.3") Dimension (W x H x D) Carton Dimension 522 x 490 x 262 mm (20.6 x 19.3 x 10.3") (W x H x D) Gross Weight ...
1.1.6 OMNI-3195-BT Mechanical IP65/ NEMA 4 for aluminum front bezel Construction Panel mount / VESA 100 Mounting 460.8 x 410 x 62.7 mm (18.1 x 16.1 x 2.5") Dimension (W x H x D) Carton Dimension 661 x 496 x 200 mm (26 x 19.5 x 7.9") (W x H x D) Gross Weight...
1.1.7 OMNI-2215-BT Mechanical IP65/ NEMA 4 for aluminum front bezel Construction Panel mount / VESA 100 Mounting 550 x 373 x 53 mm (21.7 x 14.7 x 2.1") Dimension (W x H x D) Carton Dimension 670 x 525 x 200 mm (26.4 x 20.7 x 7.9") (W x H x D) Gross Weight...
OMNI Modules Featuring a modular designed, the OMNI-BT Series Panel PC can be fitted with a number of modules to expand its base capabilities. Please refer to the sections below for their features. Note: The interface between the CPU box and the module is through PCIe signal. 1.2.1 USB/ COM/ LAN Module Features USB 2.0 x 2...
1.2.3 MiniCard and SIM Card Module Features MiniCard x 2 SIM Card x 2 1.2.4 RS-232/422/485 Module Features RS-232/422/485 x 4 (Selectable by jumper) Note: You need to install the COM Port driver Chapter 1 – Product Specifications...
2k Vdc Isolation Note: You need to install the COM Port driver 1.2.6 Digital I/O Module Features Digital I/O x 8 Note: You could use an AAEON Hi-Safe Software tool to adjust input or output Chapter 1 – Product Specifications...
1.2.10 COM x 4 + DIO x 16 Module Features Isolated RS-232/422/485 x 4 Digital I/O x8 Note: You could use an AAEON Hi-Safe Software tool to adjust input or output COM3 COM4 Chapter 1 – Product Specifications...
1.2.11 Wifi 802.11 b/g/n Module Features Support 802.11 b/g/n Support BT 3.0 1.2.12 RS-485/422/232 x 2 Module Features RS-485/422/232 x 2 Selection by jumper Chapter 1 – Product Specifications...
List of Jumpers Please refer to the table below for all of the system’s jumpers that you can configure for your application Label Function Clear CMOS AT/ATX mode selection LVDS Port Backlight Lightness Control Mode Selection LVDS inverter Voltage Selection Touch Selection COM2 +12V/+5V/RING Selection Chapter 2 –...
List of Connectors Please refer to the table below for all of the system’s connectors that you can configure for your application Label Function MiniCard Connector with on-board SIM LPC debug port Battery connector SIM socket CN10 CFast connector CN11 Board to board connector CN15 Panel size select...
2.3.6 Panel Size Select (CN15) 17 inch LCD Signal Signal DIO0(GND) DIO1(GND) DIO2(5V) DIO3 DIO4 DIO5 DIO6 DIO7 2.3.7 LVDS Backlight Connector (CN17) Signal Signal BKL_CTL BKL_EN 2.3.8 Mini PCIe Slot (CN18) Pin Name Signal Type Signal Level PCIE_WAKE# +3.3VSB +3.3V +1.5V +1.5V...
HPLG_DETECT 2.3.13 Touchscreen Connector (CN29) Signal Signal TOP EXCITE BOTTOM EXCITE LEFT EXCITE RIGHT EXCITE TOP SENSE BOTTOM SENSE LEFT SENSE RIGHT SENSE Chapter 2 – Hardware Information...
2.3.16 DC-in (CN39) Signal Signal 9-30V EARTH_GND 2.3.17 COM2 Connector (CN40) RS-232 Signal Signal RS-422 Signal Signal TXD- TXD+ RXD+ RXD- Chapter 2 – Hardware Information...
RS-485 Signal Signal 2.3.18 Remote Switch Connector (CN43) Signal Signal EXT_PWRBTN# 2.3.19 Combo connector (CN45) Signal Signal USB_CM_P7- +V5_TOUCH USB_CM_P7+ +VCC_LVDS_BKLT +VCC_LVDS_BKLT +VCC_LVDS_BKLT L_BKLTNESS_R SENSE ID1# LVDS_BKLTEN ID2# Chapter 2 – Hardware Information...
Assembling Modules To install a module: Step 1 - Insert the connector to the OMNI slot by the side of the PCB box Step 2 - Secure with the screws provided. The module is installed as the image shown below. Chapter 2 –...
Page 70
To detach a module: Step 1 –Remove the screws from the module Step 2 – Remove the module The module is detached from the main panel. Chapter 2 – Hardware Information...
Installing the Hard Disk Drive Put the rubber provided onto the holes of the bracket. Place the HDD onto the bracket and secure with the screws provided Chapter 2 – Hardware Information...
Page 72
Hook the setup on to the bar above the PCB board as shown below. Secure it with the screw provided. * Users are advised to use storage devices provided and installed by AAEON. Chapter 2 – Hardware Information...
Installing DRAM To install DRAM, remove the HDD and HDD bracket and insert the RAM module as shown below. * Users are advised to use DRAM modules provided and installed by AAEON. Chapter 2 – Hardware Information...
Mount the OMNI onto the wall Step 1 - Glue the waterproof rubber along back side of the panel Step 2 - Screw the provided mounting brackets into the back of the panel Chapter 2 – Hardware Information...
Page 75
Step 3 – use screws to secure the panel onto the wall with the wall-mount brackets Chapter 2 – Hardware Information...
Assemble the OMNI panel and the CPU Box The left photo shows the LCD Kit and the right photo shows BOXER Kit Step 1 - Plug connectors into connector sockets accordingly Chapter 2 – Hardware Information...
Page 77
Step 2 - Assemble the panel and CPU Box Step 3 – Slide the CPU Box into the panel and tighten them with screws Chapter 2 – Hardware Information...
Page 78
The assembling process is completed Chapter 2 – Hardware Information...
P-CAP Touch Screen Operating Always touch the screen with finger pads. The force of finger should be lower than 10g. Chapter 2 – Hardware Information...
System Test and Initialization The system uses certain routines to perform testing and initialization. If an error, fatal or non-fatal, is encountered, a few short beeps or an error message will be outputted. The board can usually continue the boot up sequence with non-fatal errors. The system configuration verification routines check the current system configuration against the values stored in the CMOS memory.
AMI BIOS Setup The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic system configurations, which is stored in the battery-backed CMOS RAM and BIOS NVRAM so that the information is retained when the power is turned off. To enter BIOS Setup, press <Del>...
3.4.3 Advanced: USB Configuration Options summary: Legacy USB Support Enabled Optimal Default, Failsafe Default Disabled Auto Enables BIOS Support for Legacy USB Support. When enabled, USB can be functional in legacy environment like DOS. AUTO option disables legacy support if no USB devices are connected Chapter 3 –...
3.4.5 Advanced: Power Management Options summary: Power Mode ATX Type Optimal Default, Failsafe Default AT Type Select power supply mode. AC Power Loss Last State Optimal Default, Failsafe Default Power On Power Off Select power state when power is re-applied after a power failure. Wake on Ring Enable Optimal Default, Failsafe Default...
3.4.6.1 Super IO Management: Serial Port 2 Configuration Options summary: Use This Disabled Device Enabled Optimal Default, Failsafe Default Enable or Disable Serial Port (COM) Possible: Use Automatic Settings Optimal Default, Failsafe Default IO=2F8; IRQ=3; IO=3F8; IRQ=4; Select an optimal setting for IO device Mode: RS232, 250K bps Optimal Default, Failsafe Default...
3.4.6.2 Super IO Management: Serial Port 5 Configuration Options summary: Use This Device Disabled Enabled Optimal Default, Failsafe Default Enable or Disable Serial Port (COM) Possible: Use Automatic Settings Optimal Default, Failsafe Default IO=2D0; IRQ=7; IO=2C0; IRQ=7; Select an optimal setting for IO device Mode: RS485, Disabled Optimal Default, Failsafe Default...
3.4.6.3 Super IO Management: Serial Port 6 Configuration (Optional) Options summary: Use This Device Disabled Enabled Optimal Default, Failsafe Default En/Disable Serial Port (COM) Possible: Use Automatic Settings Optimal Default, Failsafe Default IO=2C0; IRQ=7; IO=2D0; IRQ=7; Select an optimal setting for IO device Mode: RS485, Disabled Optimal Default, Failsafe Default...
3.4.6.4 Super IO Management: Serial Port 7 Configuration (Optional) Options summary: Use This Device Disabled Enabled Optimal Default, Failsafe Default En/Disable Serial Port (COM) Possible: Use Automatic Settings Optimal Default, Failsafe Default IO=2B0; IRQ=10; IO=2B8; IRQ=10; Select an optimal setting for IO device Mode: RS485, Disabled Optimal Default, Failsafe Default...
3.4.6.5 Super IO Management: Serial Port 8 Configuration (Optional) Options summary: Use This Device Disabled Enabled Optimal Default, Failsafe Default En/Disable Serial Port (COM) Possible: Use Automatic Settings Optimal Default, Failsafe Default IO=2B8; IRQ=10; IO=2B0; IRQ=10; Select an optimal setting for IO device Mode: RS485, Disabled Optimal Default, Failsafe Default...
Setup submenu: Security Change User/Administrator Password You can set a User Password once an Administrator Password is set. The password will be required during boot up, or when the user enters the Setup utility. Please Note that a User Password does not provide access to many of the features in the Setup utility. Select the password you wish to set, press Enter to open a dialog box to enter your password (you can enter no more than six letters or numbers).
Product CD/DVD The OMNI-BT series comes with a product DVD that contains all the drivers and utilities you need to setup your product. Insert the DVD and follow the steps in the autorun program to install the drivers. In case the program does not start, follow the sequence below to install the drivers. Step 1 –...
Page 107
Follow the instructions Drivers will be installed automatically Step 5 – Install MBI Drivers (Optional, Windows 8.1/ 10 only) Open the STEP 5 – MBI (Optional) folder and select your OS Open the Setup.exe file in the folder Follow the instructions Drivers will be installed automatically Step 6 –...
Page 108
For Windows 7: Change User Account Control settings to Never notify Chapter 4 – Driver Installation & Touchscreen Settings...
Page 109
Reboot and log in as administrator Chapter 4 – Driver Installation & Touchscreen Settings...
Page 110
Run patch.bat as administrator Chapter 4 – Driver Installation & Touchscreen Settings...
Page 111
For Windows 8: Open the Apps Screen, right click on the Command Prompt tile and select Run as Administrator Chapter 4 – Driver Installation & Touchscreen Settings...
Page 112
To install the driver (patch.bat), you will first have to locate the file in command prompt. To do that, first go to the directory which contains the file by entering <drive letter>: eg. if the driver is in D drive, enter D: You are now at the directory containing the installation file.
Page 113
For Windows 10 Open the STEP 7 – Serial Port Driver (Optional) folder and select Win10_32_64 Open the Setup.exe file in the folder Follow the instructions Drivers will be installed automatically Step 7.2 – Install USB to UART Driver Open the USB to UART Driver folder and select your OS Open the Setup.exe file in the folder Follow the instructions Drivers will be installed automatically...
PCAP Dual Monitor Touch Settings When two panels are used, they can set to be the primary and secondary display. The instruction below shows how this can be done: Go to Display Panel and choose your preferred primary display. Chapter 4 – Driver Installation & Touchscreen Settings...
Page 115
Go to Tablet PC Settings in Control Panel. Under Display options, select the primary display from step 1. Apply the changes and exit. *Do NOT calibrate the screen on your own. Doing so might disrupt the device’s factory calibration Chapter 4 – Driver Installation & Touchscreen Settings...
9741215513 [PER-T497], RS-232/422/485 x 2, I/O module Signal type: USB Jumper setting for RS232/422/R85 EX : RS-232 Jumper setting as bellow: Appendix C – OMNI COM Module / UART Setting...
Page 128
EX : RS-422 Jumper setting as bellow: Appendix C – OMNI COM Module / UART Setting...
Page 129
EX : RS-485 Jumper setting as bellow: RS-232 Pin Define Signal Signal Appendix C – OMNI COM Module / UART Setting...
Page 130
RS-422 Pin Define Signal Signal TXD- TXD+ RXD+ RXD- RS-485 Pin Define Signal Signal Appendix C – OMNI COM Module / UART Setting...
9741215513 [PER-T371], OMNI COM x 2, USB x 2, LAN x 1, I/O module Signal type: USB COM3, COM4 (RS232 / RS485 / RS422) Appendix C – OMNI COM Module / UART Setting...
Page 132
RS-485 Jumper setting as bellow: RS-232 Jumper Setting switch position switch position switch position switch position RS-232 Pin Define Signal Signal Appendix C – OMNI COM Module / UART Setting...
Page 133
RS-422 Jumper setting as bellow: RS-422 Jumper Setting switch position switch position switch position switch position RS-422 Pin Define Signal Signal TXD- TXD+ RXD+ RXD- Appendix C – OMNI COM Module / UART Setting...
Page 134
RS-485 Jumper setting as bellow: RS-485 Jumper Setting switch position switch position switch position switch position RS-485 Pin Define Signal Signal Appendix C – OMNI COM Module / UART Setting...
9741215518 [PER-T432], Isolation RS-232/422/485 x 4, DIO x 16 I/O Module Signal type: USB PCB back side for jumper setting: Jumper setting for RS232/422/R85 RS-232 RS422 RS485 JP1 (1-2) JP1 (1-2) JP1 (3-4) JP1 (3-4) JP6 (1-2) JP6 (1-2) JP1 (3-4) JP6 (3-4) JP9 (1-2) JP9 (1-2) JP1 (3-4)
Page 144
EX : Setting for RS-232 RS-422 Jumper setting as bellow: Appendix C – OMNI COM Module / UART Setting...
Page 145
RS-485 Jumper setting as bellow: Pin Define RS-232 Pin Define Signal Signal Appendix C – OMNI COM Module / UART Setting...
Page 146
RS-422 Pin Define Signal Signal TXD- TXD+ RXD+ RXD- RS-485 Pin Define Signal Signal 16 bit DIO Setting: Use AAEON Hi-Safe Software to configuration Appendix C – OMNI COM Module / UART Setting...
Page 147
DIO (16BIT) CN15 Signal Signal DIO1 DIO2 DIO3 DIO4 DIO5 DIO6 DIO8 DIO7 CN16 Signal Signal DIO9 DIO10 DIO11 DIO12 DIO13 DIO14 DIO15 DIO16 Appendix C – OMNI COM Module / UART Setting...
UART mode setting 1. Open the device manager in Windows 2. Find the target COM device of Fintek Serial which comes from OMNI COM Module 3. Right click and select Properties 4. Switch to page Advance Setting 5. Select the target UART Mode RS232/422/485 by item Select Mode *RS232/422/485 mode should be the same UART mode as jumper setting Select Mode of Fintek Serial Properties Appendix C –...